thank you for informative video.I just came to know about micron wing where usefull parts available for my project...thank alot
@user-vv7ex6rz7o
5 жыл бұрын
Wtf good speed.
@hiltonryllecabeguin9192
5 жыл бұрын
if i will install 2 or 4 coreless motor. what esc would i use and how much amps?
@rishavsrkr6948
7 жыл бұрын
Can you please tell me how to build one
@hansdietrich83
8 жыл бұрын
what motor/esc is that and do you know how much lift the motor generates?
@verve78arief
4 жыл бұрын
its motor work if my receiver input in 4,8-7,4 and ESC is 5A 1S and I install 1S Lipo? thanks
@thelongranger55
5 жыл бұрын
Hey is there a version of this ESC for 2s lipo 7.4 volts ? , I want to use it with a 8520 7.4 volt motor& is there a receiver for flysky that will work for me ? I only have flysky i6s transmitter
@MicronWings
5 жыл бұрын
This ESC is for brushed motors - 2S micronwings.com/Products/ESCBrushedMicro2S8AWired/index.shtml
@skylinegrechy
7 жыл бұрын
Hey buddy. This is something I'm looking for, for my school project. Did you buy the ESC or make it? If you made it, would you mind sending a photo of the circuit diagram please.
@MicronWings
7 жыл бұрын
The brushed ESC is available on our website. www.micronwings.com/Products/ESCBrushedMicro1S5A/index.shtml
@christianmerolli5327
4 жыл бұрын
can you use 1 brushed esc for 2 or more motors - probably a dumb question but idk
@syarruddin
3 жыл бұрын
yes you can. but the motor will turn with same speed. cannot be differential motor
@alexherrera3918
3 жыл бұрын
Sorry about this begginer question but why can the motor br connected to the receiver direcly? Thanks
@MicronWings
3 жыл бұрын
This receiver doesn't have a brushed motor driver on-board. However most receivers with connectors like this one these days do have either a brushed 2 or 5 amp controller on-board so you can jsut solder the motor wires to two pads under the board.
@alexherrera3918
3 жыл бұрын
@@MicronWings that makes a lot of sense to me now. thanks for the explanation!!
@itsmatinsaleemi1868
6 жыл бұрын
does the reciver works with any rc remot toys..do u sell both esc and reciver..I need one..I live in kabol afghanistan..
@MicronWings
6 жыл бұрын
This unit does not work with just any transmitter. You need a DSM2 compatible transmitter. See our website for a list of products. www.micronwings.com
@itsmatinsaleemi1868
6 жыл бұрын
can u post to afg..the compatible product..motor .prop.reciver and esc..what wil be the price..tnx alot
@MicronWings
6 жыл бұрын
The receiver choice will depend on what servos you want to run. See the compatible ones on the receiver page listed below. I have put links to the products in the video below. You may also need wire and connectors. See those sections on my website if you need them. RX - www.micronwings.com/Products/DelTangRx35d/index.shtml ESC - www.micronwings.com/Products/ESCBrushedMicro1S5A/index.shtml Motor - www.micronwings.com/Products/MotorBrushed7mmx16mm2.7Ohm/index.shtml Prop - www.micronwings.com/Products/Prop65mmTriTurbofan/index.shtml Battery - any 1S 3.7V battery is okay - maybe 130mah
@hiltonryllecabeguin9192
5 жыл бұрын
what esc is use for coreless motor?
@MicronWings
5 жыл бұрын
The ESC shown here is for a coreless motor. But this ESC is no longer available. This is a link to a popular 1S brushed ESC - micronwings.com/Products/ESCBrushedMicro1S4ABareBoard/index.shtml
@Prowlerook
3 жыл бұрын
Only for DSM2 compatible transmitters?
@syarruddin
3 жыл бұрын
all transmitter can be use
@vishalvyas6502
7 жыл бұрын
what is the voltage of battery
@MicronWings
7 жыл бұрын
The battery is 1S - 3.7 volts
@tmlrobotics5446
4 жыл бұрын
Are these reversible?
@MicronWings
4 жыл бұрын
These units are no longer in producttion but they were one way only.
@tmlrobotics5446
4 жыл бұрын
@@MicronWings Ah thanks! May try to harvest the board from a servo for reversibility.
@dondoc00
5 жыл бұрын
Esc motor betafpv 0703 19000kv ???? Thank you
@MicronWings
5 жыл бұрын
No this is just a standard 7mm brushed motor.
@dondoc00
5 жыл бұрын
@@MicronWings oh, thank you. so can you help me to start a betafpv 0703 engine
@MicronWings
5 жыл бұрын
@@dondoc00 Sorry I don't have any experiency with that system
@CarlosSD
5 жыл бұрын
@@dondoc00 You need a brushless esc, normally for those motors the esc are in 4 in 1, for that motor i'll recommend you a 6 to 7 amps esc
@DIyRcrc
8 ай бұрын
This esc does have bec
@MicronWings
8 ай бұрын
no it doesn't
@DIyRcrc
8 ай бұрын
@@MicronWings thats mean you use RX battery
@MicronWings
8 ай бұрын
The ESC is powered from 1S battery and then that power is delivered to the receiver. It's not really a BEC because if just passes whatever voltage the ESC gets straight on to the receiver.@@DIyRcrc
Пікірлер: 40