Just gave a test to your rates and I cant believe I was flying indoors with such high rates for so long!! My stress level on jobs will certainly go down!
@ketratech8165
9 ай бұрын
What rates do you charge?
@Hoss8676
5 ай бұрын
@@ketratech8165 24 min in the video
@PothocketsFPV
3 ай бұрын
@@ketratech8165 Rates in this context refers to the sensitivity of the controls
@gcdevicegc6103
9 ай бұрын
I feel the short elrs/xf antenna makes twice lower signal! didn't you? what TX settings for ELRS you have on your remote?
@kirkerr
Жыл бұрын
Great build video but I was wondering what width of flight controller can fit into the bottom frame? I have been looking at the SpeedyBee F745 35A AIO which is 36.6 X 36.5 and was wondering if it wouldn't fit.
@testchannel1834
Жыл бұрын
@troncat fpv Thank you for this video , I have built my own Pavo25 with the same components on your list except the AIO FC I used the Geprc 722 AIO . Had a little issues here and there with the AIO sensor position but finally resolved it . Looking to mod it to take the DJI 03 air unit but have to create a new 3d printed part to hold the camera and move it forward .
@mathewl7427
Жыл бұрын
Do you find it hard when you transition outdoors with those low rates?
@TRONCATFPV
Жыл бұрын
I rarely have issues with it. The only time its difficult to transition is when its windy out, but then again its difficult with higher rates as well haha
@PowerLoop-media
Жыл бұрын
Great video. Can you share your Gopro settings? Are you filming in wide or in superview? Hypersmooth or in post stabilisation? Thanks in advance.
@HaydenSummers
Жыл бұрын
4:3 GoPro 10, no stabilisation, use real steady or gyro flow. GoPro 11 5.3k 8:7 no stabilisation, gyroflow. Taking stabilisation off let’s you use the gyro data of the GoPro. Much better than hypersmooth
@cashbyclose
Жыл бұрын
What electric screwdriver is that thanks
@xrayhead
8 ай бұрын
Yes that would be nice to know as I was thinking the same thing TBO????
@YarivGilad
Жыл бұрын
I actually want to follow these steps to build this quad (my first build) and get into real-estate fly-throughs in my country. Given this video is a year old. I want to ask you for some updated pointers: 1 - Can I use "Dji 03 Air Unit" instead of the "RunCam Link Falcon Nano Kit" or "Caddx Polar Nano Vista"? 2 - The motors you used are no longer available. which motors would you use today? 3 - The only iFlight FC I could find on their site is "BLITZ Whoop F7 AIO". will it do? 4 - Would you upgrade the battery, or is it still the best option even today for this build? Thank you so much for your amazing videos!! You're a big inspiration!!
@HansBaier
11 ай бұрын
I think an important omission in this video is the Motor poles setting. It is left as default 14, but I counted only 12 Magnets on the motor bell. After changing this setting now I can get almost 10 minutes flight time instead of 8 on a 1100 mAh battery.
@rthairlines
Жыл бұрын
Great video. Thanks for this. And without the screaming of the engines and the massive wind, along with the music, it looks like a gentle breeze is blowing the camera through the house on a fluffy cloud. Love it! Oh and the LED is sick, man! XD
@TRONCATFPV
Жыл бұрын
thats exactly the vibe I go for with these walkthroughs 🙌
@sydballa6572
10 ай бұрын
Where can I get these rates to try them? They sound sweeeet
@Descvnd
Жыл бұрын
I just completed this build, everything went smoothly except the esc flash, I flashed g-h-30 the quad would wobble and yaw right when flying. Betaflight was convinced I had an IFLIGHT_F745_AIO_V2 when I have the iflight beast 55a. Took me 2 days to end up looking back in the esc config to find out my drone was running G-H-50 at 24k esc pwm??? Not what I remember flashing. Force flashed G-H-30 and 48k pwm. Solved all my problems!!!
@TRONCATFPV
Жыл бұрын
Glad you got it figured out!
@carlosbetancurt1920
Жыл бұрын
Man, I'm having the same issue.
@carlosbetancurt1920
Жыл бұрын
Can you help me?
@HaydenSummers
Жыл бұрын
@@carlosbetancurt1920 check what ur board wants, mine wanted g-H-50 and I flashed it with that. It would yaw right and wobble. I went back to esc config and it said version G-H-30 was flashed. I just corrected it and am having amazing success, smooth flights.
@carlosbetancurt1920
Жыл бұрын
@@HaydenSummersI did it thank you man but with the 6s battery and the gopro naked from geprc my front motors get too hot. But the fly is much better.
@martinshaw6907
Жыл бұрын
I spend half of my life now watching your videos I have to say your you are costing me vast of amounts of money I have just ordered parts for fpv drones and will be following your builds MANY THANKS KEEPS ME BUSY HAHAHA
@JWilly4625
Жыл бұрын
You kind of sound like thedooo lmao
@SamuelAyinde-h2v
4 ай бұрын
What other flights controller can i use
@ericcoker8784
Жыл бұрын
Ohhh man, thanks for video and time spent. I really didn't understand "air-mode" till now. All of my 65 and 75 size quads get the throttle scaled to 70-80% and throttle expo at 0.50-0.60 range (I like center stick activity for throttle). PID tune is unchanged. My Flex25 works great with my throttle tweaks mentioned above, with PID tune stock. BUT moving slow indoors!!! No way! She is a heavy girl and sensitive sticks led to ceiling "stickage" and "droppage" to the floor, 😂! Thank goodness it happened twice on the first pack and nothing broke. I got better when I dropped the 🎥 angle. Next will be the five bladed props, lower camera angle, airmode off, and your rates.
@fastvincent1
Жыл бұрын
Do you recommend any other flight controllers? The one's in the description are out of stock
@darrylmeans725
Жыл бұрын
@troncat, I like many have recreated this build in hopes to fly it as you do. Earlier today when I finished it, I forgot to reverse the motors but after I did, I was excited to see it fly. My 2nd complete build and I owe you. I used everything similar except the AIO. I went with a JHEMCU F405 40a AIO. Besides that, everything else is the same. Using the UAV Tech preset, my motors seem to be VERY hot but that could also be because I’m using CNHL 1300mah 6s batteries and I’m learning that those big boys are hunkers compared to similar 6s batteries. I’ll turn down the tune and see how that works out. Thanks again for the comprehensive build tutorial!
@TRONCATFPV
Жыл бұрын
Awesome! I have the JHEMCU F405 on one of my other cinewhoops and it works great. Yea that 1300mah may be a little much for it. I'm actually going to have a battery testing video coming out soon where I test a couple different 6s LiPo's. Mainly 550mah - 850mah. GNB has some awesome sized 6S LiPos that work great with this build.
@RandoManFPV
11 ай бұрын
Yea I recently got a 1500 cnhl 6s and when I put it on with my gopro 8 it turned my nazgul5 into a flying brick 😂
@MultiCyrrus
Жыл бұрын
newbie question here on the battery: would it handle a long range battery too (low discharge, 2,5-3000mAh?)
@DronieBoy
Жыл бұрын
Do you mind sharing your GoPro settings?? Thank you so much
@windowisdom
Жыл бұрын
Remarkable video man... Appreciate your time and effort in doing all this stuff. Thanks
@TRONCATFPV
Жыл бұрын
Thank ya 🙌 Glad you liked the video!
@OvelarFotografia
Жыл бұрын
Hi there. I saw you used HGLRC Aeolus 2500kv 1303.5 into the Pavo25 and BETAFPV 2004 1700KV motors into de Pavo30. Both of them good for 6s batteries. So, as far as you have tested both of them into a cinewhoop, which one do you prefer more?. Would you change the ones into Pavo25 to the Betafpv?. I am building a Pavo25 with the F722 35A AIO Brushless Flight Controller instead of the iFlight (Beast) you are using in yours. Rest of component will be the same. The goal are those amazing 10minutes around flight time you got there. Thanks in advance!
@goldfishhomebd1276
6 ай бұрын
Does this fly perfectly with full size GoPro? Are the motors got hot? & Can I lift a full size GoPro 10 in Geprc Cinebot 30 ( 1804 -6s motor) ?& Can I use 1300 6s 120c lipo(210g) in Cinebot30 setup with GoPro? Plz reply.... Btw, love your video ❤️
@TRONCATFPV
6 ай бұрын
Even though this build can lift a full sized GoPro, I wouldn't recommend it. Drones this size really should only be flown with something like a naked GoPro. I've never flown the Cinebot30 so I can't really attest to what it can lift or what batteries are best.
@stellarmediacollective7953
10 күн бұрын
I fly Cinebot30 with naked gopro 11 and 1100mah 6s. Works great.
@serhanercanl1362
Жыл бұрын
Hi my friend. Very successful business. Congragilations. İ am a drone pilot and video creator in izmir Turkey. And want to start fpv indoor Real estate business. But i dont know where to start. İn fact it is the remote but which one i have buy cause i dont have much budget to buy the wrong one. İ need the perfect working setup for big houses and factories. Can you give an advise about the starting point which is the controller and the protocol? Thanks for your interest.
@ktkt1825
3 ай бұрын
Love your work and videos- Thanks! I'm working to build one, and noticed you did not use a capacitor- is it not needed? Ps- the HGLRC Aeolus 2500KV are not available anymore- I went with T-Motors
@quantum_m3chan1c
5 ай бұрын
Thank's so much! Are you using the GOPRO in ULTRAWIDE mode for interiors?
@kevinglenister6520
3 ай бұрын
This may sound like a very dumb question, but the way your props are on your drone it should not fly if your motor direction is pulling in (motor 2 and three counter clockwise, motor 1 and 4 clockwise). I listen to you set the motors several times and you said they were going in the reverse of what I stated above so you reversed all of them to make it "normal" .. But your props in video do not indicate that.. Or have I missed something..... Your input would be so helpful, I suspect it is me as this is only my 3rd drone build. Thanks love your videos. PS i got my drone to fly great but my props are opposite of yours.... Confused :)
@iCrazy414
Жыл бұрын
Is there another motor you’d recommend? The HGLRC 2500kv are all sold out no matter where I look 😢
@Braincho
3 ай бұрын
Hello from 2024! Does this build is still viable or something else is better now days(may be a half inch up or down in size or same)? How would it flies outdoors for those cinematic shots or you would suggest different one for outdoors? Thank you in advance!
@manuel_a_c
6 ай бұрын
@TRONCATFPV I set this rate in my speedybee 35. I want to fly indoors site with my bee35, but it still have a lot of power. have i to limit the throttle too? any more restriction? Thanks you
@RaukFPV
Жыл бұрын
why that frame over a lumenier 2,5 or a cinelog 2,5? im considering changeing my protek 25 into another frame, the protek is super heavy, for what it is.
@TRONCATFPV
Жыл бұрын
Main reason is for the ease of assembly/service, and the fact that the ducts are all one piece. Plus its a pretty solid price 🤙
@deadmoo83
Жыл бұрын
I recently upgraded an old Beta95X to a Pavo25 for the ease of assembly.
@deadmoo83
Жыл бұрын
@@alperenozgur All I can say for sure it is a huge improvement over the old Beta95X frame. I also have a Protek35, and I like those iFlight frames. Not really concerned about finding a better frame for that one.
@saturn_fpv
Жыл бұрын
@@TRONCATFPV Ducts being separate was exactly the reason I got the Cinelog25. Much easier to swap if one breaks?
@TRONCATFPV
Жыл бұрын
The pavo25 is a HUGE upgrade from the beta95x. As far as the ducts go, for me, working on the cinelog25 was never as easy as I would have hoped. Once the ducts were off the motors tend to flop all over the place and getting in the way making repairs kind of difficult. On the Pavo25 though, the duct is its own standalone piece and isnt even attached to the motors, it makes repairs much easier. Also when you think about it, the ducts on the cinelog require 16 screws to remove while the pavo is 6. When comparing durability, I feel the pavo takes the cake. It is nice that the ducts are individual on the cinelog because they are thinner and will break easily in a crash. the pavo duct is pretty thick and since its one piece it feels much more sturdy and durable. Where the cinelog takes the cake is with the camera dampening. I really don't know why betafpv eliminated that on the pavo25 design.
@kevinhirsch5544
6 ай бұрын
I only have got a TBS Tango 2 radio, so I wanted to ask if I could also use any Crossfire receiver instead of your ERLS or would Crossfire not be compatible with the flight controller? If yes, how do I know which receiver have got good penetration and which ones not?
@Drone_Addict_
10 ай бұрын
Do you offer 25 minute consultation phone calls for troubleshooting issues that new FPV pilot may be going through. Or even a video phone call. I’ll be willing to get behind something like that. If you offer it please let me know. I’m having a lot of issues as far as getting by Drone to come off the ground. It is mostly having to do with a binding issue between my radio, master boxer, and express LRS receivers. I for some reason cannot get my drone to communicate properly. Please and thank you for everything you do. I followed the tutorial of reckon 7 inch build that you did. Mine did not come out as amazing as yours did only because Banggood screwed me on parts but I may do with what I had my crossfire module came in yesterday, so I’m hoping maybe I can get it off the ground now, but I’m still having issues on other quads. Again, thank you for everything that you do.
@djiadventures1494
6 ай бұрын
@troncat Hi man, I found your work online and its amazing. Thank you for sharing this video. I do have an issue with the parts, most of the parts are not available or not in the production. Is there any substitute for theese parts!
@HansBaier
Жыл бұрын
I just tried the Gemfan 5 blades on my Cinebot30 and they are FANTASTIC! So much smoother and easier to control and they sound so much better too compared to the HQProp 3 blades. Great tip, thanks!
@mathiaskrokos8961
Жыл бұрын
which exact article are the blades for the cinebot 30?
@lopesdev
6 ай бұрын
Do you use cinebot 30 for real estate/indoors? Im not sure if i get cinelog 25 v2 or cinebot 30 for this type of works.
@HansBaier
6 ай бұрын
@@lopesdev No I don't have the drone anymore. I have a Pavo25 and DarwinFPV Cineapes now. Especially the Cineapes I like very much.
@tbrown1352002
4 ай бұрын
Would this tune work equally well on any other build or is it best on a cinewhoop style drone only? Big thanks from a fellow New Englander for the content and advice!
@Brazo.officiel
Жыл бұрын
Thank you for this great video Maybe I missed something but Could you tell me what is the degree of amplitude of your camera when you fly ?
@Lift33d
5 ай бұрын
Hey man I have the new betaflight and can’t find that tune .. is there a way I can just copy what’s in your screen or where do you recommend I get the files I need from maybe Betaflight Discord?
@zenandtheartofskateboarding
5 ай бұрын
I gotta ask or it'll drive me insane, when I tried this build the motors overheated like crazy until one blew up, I know the motors claim to work w 6s but google and forums say their kv is too high for 6s, is there something I missed that would've made them actually work w a 6s battery?
@jeanmosquea9539
6 ай бұрын
What goggles would I need to get fot this (beginner here) and how does this compare to a stock version?
@sydballa6572
9 ай бұрын
So glad I found this video. Thank you for taking the time to soundly explain everything from start to finish. As someone who is learning, you’ve encouraged me to try this build. I currently fly a cinbot 30. Should the settings you’ve explained help my quad fly better indoors?
@stellarmediacollective7953
10 күн бұрын
i run them on my cinebot30 too.
@itsonlystuff
Жыл бұрын
Hi mate, I've been buying the parts to build this but the HGLRC Aeolus motors arnt in stock anywhere! (I'm in NZ so makes it harder). Any recomendations of similar motors that might work for me? Thanks!
@tobiasisaksson3764
7 ай бұрын
Do you use iflight blitz whoop aio 55a, cant find any named beast
@pes_Arnold
8 ай бұрын
These purple batteries are light in weight. All other 1100 mAh 6S batteries are much heavier!
@djiadventures1494
6 ай бұрын
There are no motors available I scrapped google. Can anyone tell me what is the alternative to them? 😢
@CaseyRodriguez-xb3jn
2 ай бұрын
Would you reccomend this over your qav nano build?
@DevonSpittleREAL
Жыл бұрын
Well done 👍🏻. Do you ever adjust your throttle limits? And is your camera angle really low? Thanks!
@TRONCATFPV
Жыл бұрын
It really depends on the build, for this one I didn't have to but you can to help with throttle blips
@saturn_fpv
Жыл бұрын
I was so sure he uses throttle limit or expo to combat wavy lines, surprised he doesn't!
@AdamVenturesTravel
Жыл бұрын
Thanks for the build guide! I built the same drone and my rear motors are running hot.. Like too hot to touch after 1min of flight time. Only the rear motors. is this an issue I need to solve, or is this pretty common on cinewoops?
@DudeMaybeSomeday
Жыл бұрын
First of all, thank you for this incredible video. As a beginner, content like this is priceless. I am going to build my first drone/cinewhoop and it seems like this is the one. You published this 6 months ago, so would you still recommend this to someone like me, or are there any things you would change after having spent quite a bit of time with it? Could you run the 03 Air Unit on this build?
@TRONCATFPV
Жыл бұрын
This has been my go-to indoor drone since publishing the video and I love it. Only thing I’ve changed is the antenna on the back I have upgraded to a trueRC carbon fiber matchstick antenna. If you go that route let me know and I can send you the custom STL to fit that antenna. Otherwise, it’s one of my favorite drones. I’ve seen some 3D printable files that are for this frame that hold the O3 camera but I haven’t tried them out. It looks like it should fit though 🤙
@SiOgie
Жыл бұрын
This is it! The video I've been waiting! Great build, great information! You're awesome. Gonna try it very soon on my drone. Thanks a lot.
@walasfilms
2 ай бұрын
No expo for indoor flight? I tought I was supposed to increase that
@fxfawkes
Ай бұрын
Such a valuable video. Thanks man!
@nuriev116
Жыл бұрын
Why do you use gopro? Dji 03 is pretty good for using without gopro?
@royl1211
7 ай бұрын
Can you share the music you used?! Thank you!
@mrMihaylo
Жыл бұрын
My friend! You promised to tell us about your cinelog25 settings to fly smoothly. I didn't see such a video from you. My slow flight is up and down and I do not know what to do.
@TRONCATFPV
Жыл бұрын
That is included in this video in the betaflight setup 👍
@sirindas1999.
Жыл бұрын
Where we get this parts?
@TRONCATFPV
Жыл бұрын
links to everything I used in this video is in the description 👍
@BrandinoTheFilipino
Жыл бұрын
what is your bettaflight tune pls?!!!!
@eturnerx
Жыл бұрын
Thanks for the video. I learned a lot. I have a Pavo25 and keep bobbing and blipping it into to the ceiling! Air mode off, lower rates I think. Maybe an indoor/outdoor switch.
@TRONCATFPV
Жыл бұрын
yea deff try out that BF setup and it should help ya 👍
@leahcim501
11 ай бұрын
Why not just use a crossfire Nano RX?
@Tufenuff83
5 ай бұрын
What controller/goggles do you use?
@nkdurrett
5 ай бұрын
What goggles are you using on this rig???
@evansamson2703
Жыл бұрын
Question is it ok to apply that preset even thought it give that warning ? I applied it to my cinewhoop but went back to stock pids because of that
@TRONCATFPV
Жыл бұрын
Yes you should be fine! Once you have the preset enabled do a quick hover test without goggles on to make sure motors aren't piping hot. If you need any help with it shoot me a message on patreon 🤙
@evansamson2703
Жыл бұрын
@@TRONCATFPV thanks
@krisgleave
Жыл бұрын
Hi, the parts are difficult to get for this. If I were to use the new Speedybee F7 AIO and look for some other motors with a similar size and KV do you think I’d be able to achieve similar results? I don’t tune quads as no experience with that. I just want it for slow flying indoors like yours. What I want is an indoor drone, ideally with O3 as that’s what I always fly but be able to hold a GoPro Mini 11 and ideally around 8-10 mins flight time. Would you still recommend this build and with the tweaks I mentioned above what do you recommend think would work or not work?
@efelton2699
Жыл бұрын
To bad you can’t get the aio anymore.
@davidpujalte6774
6 ай бұрын
what's the main advantage of having 6s over 4s on this kind of build? Longer flight times? (As the power is not a deciding factor on an indoor cruising build)
@TRONCATFPV
6 ай бұрын
I’ve been using 6s because I do notice slightly better flight time plus when I need to fly faster 6s gives you a little bit more umph
@manojmohan7264
Жыл бұрын
Hello, I love your video and flying style. I am a beginner and have a bunch of questions. Any help is much appreciated. Thanks in advance. 1) Do you think these rates would work decently on the cinelog 25 ? 2)when I fly, I can see every small move i make on the sticks on the feed and that makes it very Jerky. How do you do it so smoothly ? Any tips ? 3) my cinelog 25 is designed to ARM when its on STAB mode. It sounds smooth when I ARM it. But the moment I flick to acro mode, it sounds very erratic. Wondering if thats normal. 4) I am unable to see my flight time on the goggles. I do see an entry with the time at 00:00. But it doesn't start counting up. And I dont see any stats when I disarm. How do I get it ? 5) I took it outdoors near a river one day and the feed was so pixellated even when the quad was just 10 feet from me. I thought a crossfire would have great range. Any tips there ? ( I tied the wire that goes from the camera with a metal wire tie. Wondering if that would cause a problem) 6) what are the benefits of ACRO mode over HOR mode when flying indoors ? I find the HOR mode to be very smooth. Do all indoor pilots fly in Acro mode ? Thanks again !
@TRONCATFPV
Жыл бұрын
1) These rates should work fine on a cinelog. The only thing I can't vouch for is the PID adjustments/cinewhoop preset 2) Best tip for this is trying out the rates that are in this video 👍 3) This i'm not sure about. I'm not completely familiar with how GEPRC has setup the Cinelog25 from the factory. Feel free to send me a video of this issue to contact.troncatfpv@gmail.com 4) Are you flying digital or analog? unfortunately with digital as far as I know, the flight time OSD feature doesn't work 5) Crossfire should be fine, it sounds like you have an issue with the video transmission. I would definitely remove the metal wire tie and replace with a cheap plastic one to see if this resolves the issue. Things like this can actually interfere with the signal. 6) I prefer acro because it makes the video alot more fluid. When in angle or horizon the drone will always be trying to level itself out and this can interfere with the overall fluidity in a video like this. Hope this helps 👌
@manojmohan7264
Жыл бұрын
@@TRONCATFPV wow thankyou very much for the elaborate reply. I will try out all your recommendations and keep you posted :)
@blackdim3617
Жыл бұрын
Awesome video, i learned a lot,many thanks!!!
@zeuph5013
Жыл бұрын
By running a 1404 2800kv motor, is it going to solve the warm motors when carrying the go pro? With the additional weight of the motors and thrust, is it going to be able to maintain the same flight time or at least go near the 10 minute mark? Thanks
@TRONCATFPV
Жыл бұрын
I've been doing some testing with other batteries and a full sized GoPro and am getting 5 minute flights surprisingly. I don't think you'll be able to achieve 10 minute flights with a full sized GoPro no matter the battery you use.
@zeuph5013
Жыл бұрын
@@TRONCATFPV thank you! I appreciate your reply
@YoungWhite01
8 ай бұрын
Thanks for the video! Really informative & definitely made me decide to build me next cinewoop. Had a question.. since you’re flying acro, I’d imagine your horizon isn’t almost level when you input roll to make turns; are you using horizon lock in post stabilization to overcome that issue?
@whitewingsfpv
Жыл бұрын
Why do you use a 55A flight controller? What happens if I put a 45A or 35A flight controller in your configuration? The current consumption of your motors does not exceed 10A. Please explain the purpose of installing a more powerful ESC?
@itsreallytom4310
Жыл бұрын
Really ignorant n0oB question… if I wanted to build this frame but wanted to use the DJI o3 air unit what would I be substituting out for the DJI gear? Thanks in advance. Pretty new to diy fpv and would love to learn more it’s just overwhelming with all the jargon. Any suggestions for forums or blogs?
@LifeofAccro
Жыл бұрын
i just recently switched to elrs but 2.4... is there a particular home size where 2.4 wouldnt be viable for penetration vs 915? im somewhat new to fpv and all the techno babble but not a total newbb, thx!
@TRONCATFPV
Жыл бұрын
This is a great idea for a video. Honestly, you'll probably be fine for residential real estate on 2.4. Big reason I use ELRS 915 or Crossfire for these setups is because I use them in large facilities like warehouses or manufacturing facilities. In these massive buildings I feel the 900mhz is a bit more dependable.
@LifeofAccro
Жыл бұрын
@@TRONCATFPV thanks... just placed a nice lil order on amazon so when you see that hit in the affiliate backend ;) i always love seeing those commissions hit when im checking my analytics and even more when its the actual items im recommending =)
@andrewfedder9354
Жыл бұрын
I’m a beginner, do you normally only put 3 screws into the motor instead of 4? Am I seeing it wrong and does it only take 3 screws?
@andrewfedder9354
Жыл бұрын
Right around 33:26 you can see what I mean
@joeyviggers6041
Жыл бұрын
What FC/ESC would you recommend when the iFlight options are all out of stock. Looking at the Foxeer Reaper AIO V2 F745
@inmaniac
11 ай бұрын
You don't use any expo on throttle? What black magic do you use to keep it so flat? :o Maybe the weight helps you? I use a Cinelog20 with the same tune and have trouble keeping it level.
@harelaerialphotography6593
Жыл бұрын
How do the 1303.5 motors handle full-size GoPro and how much flight time do you get?
@TRONCATFPV
Жыл бұрын
They come down warm, but not hot. You could definitely fly it with a full sized GoPro but you'll get much shorter flight times, and you'll definitely want to use a smaller battery. I would like to get some smaller 6s and 5s batteries in the 500-600 range to test out with a full sized GoPro and specifically the hero 11 mini. Once I'm able to do these battery tests I'll be posting them on my patreon and possibly here 🤙
@harelaerialphotography6593
Жыл бұрын
@@TRONCATFPV Ok thanks!
@admekar
Жыл бұрын
Can you give this drone to me
@fokusfpv
8 ай бұрын
@Troncat - what are your thoughts on the pavo 25 v2 vs. the original used in this build. they say the new ducts give more thrust, so I'm not sure if that's an advantage or disadvantage for real estate.
@keribangrebus8820
Жыл бұрын
CRAZY BUILD. 2 inch with full size gopro? get out of here. love your work man!
@TRONCATFPV
Жыл бұрын
Thing is a beast (pun intended). I was amped when it lifted that Hero 9. Stoked to throw a hero 11 mini on this thing and see how it does!
@keribangrebus8820
Жыл бұрын
@@TRONCATFPV how did you shoot flying outdoors to indoors? Did you put the ISO to auto?
@Zionson1
Жыл бұрын
Can this carry a full gopro? I'm very new to this and love to get into FPV and I'd like to build a cinawhoop. Can I buldnone using the esc etc on a different 2.5 body?
@diegolagos9702
Жыл бұрын
Hi bro! I have hot motors with that setup :,( can you share me your CLI ? Thanks
@TRONCATFPV
Жыл бұрын
Did you do this exact build? If you're using different FC/ESC, motors or even props the tune I did in this video may not work as well.
@LockJawFPV
Жыл бұрын
Very nice brother I have a foxeer 25 and a cinebot30 what's that impact pen you have who's the manufacturer I likes that have to get me one appreciate the awesome content
@carlosbetancurt1920
Жыл бұрын
I just bought some parts to start mine couse my cinelog25 bubbling a lot I need something stable. Thank you nice vide.
@neilfpv
Жыл бұрын
Amazing build video, always! What are your thoughts on 1303 vs 1404 motors? Why did you pick 1303?
@TRONCATFPV
Жыл бұрын
thanks! I was initially planning on using a set of 1404 Toka motors but they are 12x12. and dont fit the frame (pavo25 requires 9x9 only) and theres not alot of options out there in 9x9. I saw the 1303.5's and saw they had a nice low KV that I was looking for and figured I'd try em out. Plus I have aeolus motors on my cinelog and love em. They've been holding up awesome and perform great!
@neilfpv
Жыл бұрын
@@TRONCATFPV Thank you so much for sharing your thoughts about it. :)
@juanjones7121
8 ай бұрын
Great vid. Just wondering if this build can sustain the O3 air unit?
@TRONCATFPV
7 ай бұрын
you'll likely need an alternative camera mount for the O3, the rest should fit no problem
@jameson9977
9 ай бұрын
What kind of controller set up do you use? Are you rocking goggles?
@TRONCATFPV
9 ай бұрын
I've got another video in this playlist that covers all the gear I use 😉
@JDHambo
Жыл бұрын
Hey bro about how much would this build cost in aud. I fly a tiny whoop and im looking to start fpv real estate. Love your vids.
@HansBaier
Жыл бұрын
Would you recommend this build over the Geprc CineLog 35 V2? What advantages would it have?
@JonFloFPV
Жыл бұрын
So looks like you do acro mode with super low rates vs angle mode? I thought my rates were slow but yours are about half of mine! Lol
@gabinofpv
Жыл бұрын
i cannot find those motors anywhere in stock! is there some similar motors you can recommend? i already ordered everything but motors lol
@karanhiragar4587
Жыл бұрын
Bro which remote control and headset you use...send me the link to purchase
@TRONCATFPV
Жыл бұрын
I use the DJI goggles 2 and an ethix mambo TBS Ethix Mambo: bit.ly/3L2kXGx DJI Goggles 2: bit.ly/3jz9KEp
@mathiaskrokos8961
Жыл бұрын
so the build is around $520 (includes 4 6s batteries)?
@dronefilmsgermany
Жыл бұрын
Was this an analog build?
@FreshPanda97
Жыл бұрын
thanks mate, what about thorttle expo, throttle limit and throttle mid? Many people swear by it I just dont have any clue where to start with the throttle tuning
@mathiaskrokos8961
Жыл бұрын
which receiver and maybe other needed parts should I use if I fly crossfire?
@SniperUSMC
Жыл бұрын
Forgot to ask about FPV Goggle's, anything but DJI proprietary stuff would be nice, which ones do you use that works with this drone?
@iyusfpv
7 ай бұрын
hi sir, you prefer to use air mode or acro mode whe you fly in indoor situation like this ?
@TRONCATFPV
7 ай бұрын
Always acro 👍
@sten6537
Жыл бұрын
How are you handling the throttle? I find it very touch-ie in the middel and still a bit powerful. Already fiddled with settings. Got Throttle limit scale 80% and throttle expo 0,50.
@ferocious_r
Жыл бұрын
When you fly in a house like that, do you fly acro mode? Or angle?
@TRONCATFPV
Жыл бұрын
Acro 🙌
@GiorgioCanepaMBG
7 ай бұрын
+1!
@joelmulder
Жыл бұрын
I am very confused by the fact this house appears to have two side by side toilets
Пікірлер: 427