This is the drive train. 1/4 hp, 1725 rpm. 1.5" to 6" pulley reduction. The 3rd shaft is only 27 rpm. This shaft will hold the crank arms. Keep watching.
Thats the best example to describe gear reduction without rocket-science. Thank you
@jeffreykroll1170
5 жыл бұрын
The best rotation conversion video I’ve watched yet. Love the tri conversion. We did this growing up with all kinds of things in the farm. Don’t let the naysayers who don’t understand the basics of rotation stop you from providing videos.
@musicmaneman38
5 жыл бұрын
A gearbox would be better. Maybe a 40:1.
@jeffreykroll1170
5 жыл бұрын
MrE2112 I completely agree. I have watched so many ridiculous videos that I had to give you credit for creating a conversion that made sense without confusing the masses. We used huge tractor rims to increase power.
@jeffreykroll1170
5 жыл бұрын
There are many of us that understand fear ratio yet refuse to complicate the basics with people. I’m making a steam punk style can crusher with all scrap and it will have air involved just to embellish the effect once the sensor eyes catch the can. I had a vid for the motor works but watched yours and thought,.... ya know what,.... this guy has the vid. 40:1. For my downplay of the motor might work but I FOIND that a slip chain worked better. Made my final production much more dramatic and increased my pressure. Full cans of veggies. Makes a mess but at least I know the power is there.
@jeffreykroll1170
5 жыл бұрын
MrE2112 Again thank you. From al of us that don’t make videos and still putter around online. Thank you. Your convert has been the simplest and yet the most effective.
@musicmaneman38
Жыл бұрын
Just getting vack to you on this but.. the motor was only 1/8hp at 1725rpm. The torque was the payoff.
@cid4887
6 жыл бұрын
this is what i'm looking for before making one. i'm thinking first of a bicycle front and rear sprockets. thankyou for sharing.
@user-zv4zr6lt6w
8 ай бұрын
I have a five-horsepower motor with 1,400 rpm, but I need 60 rpm. Will implementing this idea achieve the goal? Thank you very much.
@musicmaneman38
8 ай бұрын
The reduction was 1.5-6 through the stages. So it woud be slower. Use good bearing blocks instead of the home made ones that I made.
@user-zv4zr6lt6w
8 ай бұрын
@@musicmaneman38 Thank you
@balementelah
2 жыл бұрын
Sukses selalu bang, ini video yg sy butuhkan
@subramaniyanp63
Жыл бұрын
Thanks so much. Did in saw this vedio very very usefull ❤❤❤😊😊iam from india madurai 🙏👍
@balementelah
2 жыл бұрын
Alhamdulillah ini yg sy butuhkan.
@edwinnoerieraguzman2323
Ай бұрын
Una pregunta el motor de cuan tas revoluciones son por minutos
@aristidessalazar8446
Күн бұрын
Hola sirve para instalarse lo a una pento que no tiene el suficiente cauda de agua csuda
@firmanatg2116
4 ай бұрын
Assalamu'alaikum, bisa gak abang buat satu experimen, pompa air dari kincir angin dan pengatur kecepatan pakai puley ke tabung sedot air.
@firmanatg2116
4 ай бұрын
Memang mungkin kecepatan dari angin bisa tidak stabil.
@puisiku666
Жыл бұрын
Terimakasih informasinya sangat bermanfaat sekali salam kenal sukses selalu
@Riswandii
5 жыл бұрын
Thanks for this videos
@r.sjaimalaevents8057
2 жыл бұрын
1440 Rpm moter hai to hume kitne inch ka pulley use karna hoga moter. Aur shaft me bada aur chota pulley size . please batliyea
@Traveling_with_jk
3 жыл бұрын
Put on water base opp diraction low rpm to high voltag and rpm
@sunoffsetengineering..995
9 ай бұрын
Moter speed=1725rpm × pulllly size 3''inch, = 5175rpm..... 5175÷10'' inch pully =517.5rpm.. 517.5rpm×3'' inch pully 1552rpm... 1552rpm÷10'' pully 155 rpm... 155rpm ×3'' inch pully 465rpm.. 465rpm ÷10''inch pully. 46.5rpm... 👌👌👌👌👌
@bodeine454
Жыл бұрын
This might be the type of setup I need to use on a homemade vehicle tire mounting machine except the last driven pulley would probably need to turn maybe 3/4 as fast or maybe even half. Do you think the last pulley has enough torque to mount a tire on a rim? I'd need the last pulley to turn 1 revolution in something like 10 seconds or maybe a little less.
@musicmaneman38
Жыл бұрын
No way. A gearbox would be better.
@bodeine454
Жыл бұрын
@@musicmaneman38 Thank you 👍
@indrastreetpunk228
Жыл бұрын
Mesin cuci kah itu bg?
@vairagijayesh
5 жыл бұрын
Thanks bro ..I understood what is used of wheel ..to reduce the speed of motor..
@abdojrjs
2 жыл бұрын
الله يعطيك العافية
@musicmaneman38
2 жыл бұрын
English please. Thanks.
@kapahrt3424
4 жыл бұрын
Thanks for share
@piecetoyou8285
3 жыл бұрын
Ime doing this type of system to slow down a wet stone, so my water don`t splash every where, Don't have speed control on my motor
@musicmaneman38
3 жыл бұрын
A gearbox would be better.
@piecetoyou8285
3 жыл бұрын
@@musicmaneman38 Yes i did consider that but a bit pricey and the cost for delivery was a little to much, I had built my system and it works great as I already had all the stuff in my garage to build a pully system, But my second pully was place high near the motor to reduce the overall length, And I only needed two pulleys after the motor for the speed I needed,
@nainaarrahman6255
3 жыл бұрын
Low rotation = High power
@bhagasasi425
2 жыл бұрын
*Torque
@ji-awtv5592
5 жыл бұрын
How do you reduce the speed of the 2nd and 3rd pulleys??
@chrisclemmey1500
4 жыл бұрын
jiaw bermz for example, if the small pulley is half the size of the large pulley, it will rotate twice as fast as the large pulley. The large pulley is then connect to another small pulley by using a shaft, these two pulleys spin at the same RPM. That small pulley is then rotating at twice the rpm as the next big pulley but half the rpm as the first small pulley. So on and so forth. This is how you transform RPM into torque.
@musicmaneman38
2 жыл бұрын
1.5"-6"
@fuzzzeballs
3 жыл бұрын
what are the mount block called holding the spindles? I am no expert on this and don't know the technical jargon to source parts, cheers
@musicmaneman38
3 жыл бұрын
I made them from aluminum blocks with bronze bushings. Use bearing blocks instead.
@fuzzzeballs
3 жыл бұрын
@@musicmaneman38 thanks for answering
@almerviray7431
3 жыл бұрын
in the 2nd pulley what is the size..for the use of ice crime machine
@musicmaneman38
3 жыл бұрын
1.5" & 6".
@almerviray7431
3 жыл бұрын
what is the size of v pulley
@wajahbaruservis
2 жыл бұрын
dinamo penggerak berapa rpm itu pak,makasih
@bhagasasi425
2 жыл бұрын
Input 1725rpm, output 27rpm
@mokshsadhwaani
2 жыл бұрын
What is the shaft size?????
@wazaifeshazli1041
5 жыл бұрын
My motor is running but pully is not moving .. PLZ tell me why?
27 rpm. 1725 Rpm x reduction .25 = rpm, x .25 = rpm x .25 again. Repeatedly.
@MaheshSharma-xx1jm
4 жыл бұрын
@@musicmaneman38 can you talk to me in private ! I want some suggestions from you actually I am making a project so need some statistics !!
@YUMI-hf1hp
4 жыл бұрын
Is that good for ballmill turn?
@musicmaneman38
4 жыл бұрын
I would use a gearbox instead. Maybe a 90:1.
@AbdulRehman-eg4ph
8 жыл бұрын
good
@ranjitpaperplate
6 жыл бұрын
Belt no kya hain
@lennongroover4189
4 жыл бұрын
Where’s the crushing pt???🤔🤔🤔
@musicmaneman38
4 жыл бұрын
Dead project. The idea was to hook up a sliding piston with arms on the last shaft. I had no way of adjusting the tension on the pulleys.
@pramodm3540
3 жыл бұрын
Part 3 kzitem.info/news/bejne/p3lsuqZ9sax4gH4
@user-qh2cr1un2s
2 жыл бұрын
زياذة العزم وتقليل السرعه
@kopipait8680
Жыл бұрын
what size pulleys?
@musicmaneman38
Жыл бұрын
1.5" - 6".
@iwan1301
2 жыл бұрын
Big torsi
@HasanBSF
4 жыл бұрын
😍😍
@fhdl1
6 жыл бұрын
What RPM u get in last pulley
@musicmaneman38
6 жыл бұрын
Tanveer Hussain 27rpm
@fhdl1
6 жыл бұрын
Good work bro, gear motor cost more using these pulley system is economical and doea the same work. I needed it for my project of extrusion machine. Will work on this system only.
@musicmaneman38
6 жыл бұрын
I am not sure what you are making but i can tell you that the bronze bushings for the bearings are not efficient.
@fhdl1
6 жыл бұрын
Thanks for the suggestion, and the pulleys are not properly aligned
@musicmaneman38
6 жыл бұрын
Tanveer Hussain the first one was bent a bit. Cheap aluminum.
Пікірлер: 93