This was super helpful and informative. Straight to the point. Thank you!
@stephenstrang590
3 жыл бұрын
This should have so many more views. Thank you.
@CHUKDEPHATTE
3 жыл бұрын
why would it? it is a specific video covering a specific topic and so the youtube algorithm probably ignores it, unless it something you search for. like i did :D.
@louielouie503
Жыл бұрын
Thank you! Thoroughly explained but made it easy to understand! Well done sir!
@davidartina5022
2 жыл бұрын
Brilliant, simple, accurate and clear explanation. Thanks very much.
@KirasNote22
3 жыл бұрын
That was quick and informative. One of the most helpful videos ever for someone who didn't know where to begin with all these options.
@diggersouth
3 жыл бұрын
I need to drill 2 holes in a very hard wood desk about 7/8 thick. I think the Brad bit will do it. The twist bit didn't make a dent. Thank you for the info. Good education.
@avinashbhujan1376
Жыл бұрын
Explained like a pro
@anothersomebody8195
2 жыл бұрын
Hmmm, I was hoping for a more thorough dive into this subject. Like more of a comparison. One goes in at an angle but what about the rest? Very clear and clean presentation though 👍
@homoeoremedy_drjayanta
4 ай бұрын
I need to make a hole approx 16-18" (wood) ,Like PVC pipe. Pls advice. Thanks in advance
@ChinhNguyen-yb3cp
2 жыл бұрын
Thank you! It’s really helpfull.
@MeandMyStaffy
Жыл бұрын
Very helpful!
@marcsugi
3 жыл бұрын
I don't know why I like to collect those round leftover from a hole saw drills.
@contactsaurabhsomani
3 жыл бұрын
very helpful. 👍
@utubesanjay
3 жыл бұрын
Wow. Did not know this.
@DIYAtoZ
3 жыл бұрын
Which drill bit is best for Drilling 2-3 mm bamboo without crack?
@johnberger5539
5 ай бұрын
What's a "mole"?
@johnberger5539
5 ай бұрын
Did you mean "mill-e-meter'?
@Toshiro_A1
16 күн бұрын
Where can i get the turbo drill bits
@johnyuhaschek5815
2 жыл бұрын
can a concrete penetrator drill bit be used to bore a hole in a wood post?
@Gollammeister
3 жыл бұрын
It's be nice to be able to find a full set of Brad point Hex shank 2mm-10mm drill bits one piece hss not 2 parts bonded friction together as I found a cheap set to be
@AsifKhan-bp6yo
4 жыл бұрын
Thanks
@marjot2009
3 жыл бұрын
what kind of drill is that? is it with a red head? Model brand?
@mohamadsyahdan5479
3 жыл бұрын
TQ
@brenoqueen873
3 жыл бұрын
what to do if the bit isnt going through and starts smoking?
@nenadsha
2 жыл бұрын
can someone explain to me how to drill a 4mm hole in a wooden stick that is 1cm in diameter and 10cm long 
@patkav
2 жыл бұрын
Hey thanks for the lecture: However I have a question for you if I may: Can you tell me what am I doing wrong with my Forster Drill Bits as well as regular wood drill bits while drilling hard woods the all get very hot and starts smoking. Is it due to the quality of bits material? Is HSS better than regular bits? Your answer is appreciated. Thx
@waldolemmer
9 ай бұрын
You might be applying too much pressure. You can also try drilling a smaller hole first and then stepping up
@hul8376
2 жыл бұрын
Nice
@thechileacademy4800
4 жыл бұрын
Which Bit would you recommend for drilling through a 6x6 wood post to be able to insert a 6inch bolt through it?
@markp8295
4 жыл бұрын
What diameter bolt? Probably an auger bit, because they are made in large lengths, but if the hole doesn't need to he precise, and you aren't drilling a lot of them, a spade bit is much cheaper. Very few small diameter Brad points are long enough. Same for twist drills.
Пікірлер: 33