This man went full hipster which is necessary when working with 35mm film. Great video
@goldenhourkodak
3 жыл бұрын
A hipster from 2009
@Mosesybanez
15 күн бұрын
Lol facts
@Ricardo-SW
3 жыл бұрын
Admiring your steady hand as you pour into the bottles- I'd have spilled without a funnel :)
@chasedionisio
Жыл бұрын
Love this kit, I’ve developed many rolls that have came out great!
@agt5jx87
3 жыл бұрын
Great video and very helpful. Edit out the talent opening the bottles.
@jaidamann8365
3 жыл бұрын
i assume he rinsed out the mixing container and stir wand off camera - to prevent contamination.
@kcat126
3 жыл бұрын
LOL, I thought (hoped) that he did too. It just reminded be to be hyper aware of my own doing this to my wand, measuring cups, and thermometer.
@GlazersCamera
3 жыл бұрын
Yes, sorry, Devin had assistants rinsing and drying between shots/chemicals.
@nestorpool
3 жыл бұрын
I was looking for this comment after watching the video at 03:42 I was afraid...
@samonthebrink
2 жыл бұрын
came here to say this
@johnfmichael
3 жыл бұрын
Also, at 9:42 he says "final agitation" on the blix, but the timer only shows just over 3 minutes, even though he said the agitations for the blix are every 30 seconds for a total of 8 minutes. How can the final agitation occur only 3 minutes into the blix step? Or did I miss something?
@BENBASIL
2 жыл бұрын
I noticed the same thing, I’m guessing he was still thinking 3:30 like the developer and it was an editing mistake. I doubled checked the instructions and it is in fact a total of 8 minutes, agitating every 30 sec 👍🏼
@maxm.2824
4 жыл бұрын
Underrated video.
@FunkyMonk_96
2 жыл бұрын
How do I clean all my equipment? What do I use to clean up and how do I dispose of any trash if I make a mess? Can I just throw them in the garbage?
@thecanadianslimer1379
Ай бұрын
I have this bracket and 20onces goes right up to the top of the beaker ??
@maririnn
3 жыл бұрын
do you just pour the used chemicals back into the containers?
@goldenhourkodak
2 жыл бұрын
Yes with a funnel
@seboc1
11 ай бұрын
Use butan spray to prevent oxidation of solutuions. Write the date of mixing on the bottle and developed films.
@lunaartemis5511
9 ай бұрын
I wish this came up earlier before i had a breakdown because the instructions and other YTs were just confusing me. This helps so much. Thanks. Do i just pore the chemicals back into the same bottles? And does this mean adding more time. (Written instructions are hard to understand in that chenical reuse section)
@memoirsofhadrian
7 ай бұрын
Same here. The other videos are waaaay too complicated for a simple procedure.
@MR-nz6db
2 жыл бұрын
Can I reuse the chemicals?
@johnfmichael
3 жыл бұрын
At 0:48, the thermometer only reads about 116 degrees, not quite the 120 degrees stated for the temperature requirement for mixing the developer. Does this mean there is some elbow room regarding the temperatures for mixing the blix and stabilizer as well?
@goldenhourkodak
Жыл бұрын
Yes. It just need to be hot enough to dissolve.
@s47industries
3 жыл бұрын
So if I’m just mixing the chemicals and not going use it right then and there or even the same day, do I need to bring up to temp? Or will the chemicals not mix correctly if not at temp? I just want to have them ready for when I do have a roll to develop, and not have to do this whole process when I do want to develop. Like my DF96, ready to go just bring up to temp when I have a roll ready.
@bbx2712
3 жыл бұрын
Sir you are the best . THANK YOU
@brookswitta
3 жыл бұрын
are these chemicals re usable?
@Harrison615
22 күн бұрын
yes abt 24 times
@sequentialable12
3 жыл бұрын
Marvellous video
@JerryAdam
3 жыл бұрын
Thanks for the video! You should have worn some protection like gloves, etc. though (:
@GlazersCamera
3 жыл бұрын
Good call!
@Dangoldmedia
3 жыл бұрын
Excellent video - thank you
@aLittlePal
3 жыл бұрын
the person just drop the film at the end of the process, he does indeed really really care about it. I can totally feel it.
@throtol
3 ай бұрын
How long can the mixed chemicals last before expiring or losing their concentration?
@jimdandy567
3 жыл бұрын
So how long can you store the kit after mixing? How long do the chemicals last?
@JonathanRuiz
3 жыл бұрын
It develops 24 rolls of film and Cinestill just says it has “Long lasting shelf life” which is not very helpful. If you look online some people say they keep their chemicals for 3 to 6 months but there’s nothing official that I can find.
@pilsplease7561
3 жыл бұрын
@@JonathanRuiz Ive used chemicals stored in glass bottles for 12 months. Ive had the same E6 kit going for 50 rolls of film for example and its 14 months old and still works like it was made yesterday. So chemicals far outlast what is stated with no quality loss.
@kcat126
3 жыл бұрын
@@pilsplease7561 Super helpful comments. I just developed my first color roll tonight, after watching this video and reading your comments. Thanks!
@pixeltx3364
2 жыл бұрын
@@pilsplease7561 can i save the chemicals i used instead of get rid of them so i can use them again??
@pilsplease7561
2 жыл бұрын
@@pixeltx3364 you can use them up to like 6 times, If I recall you can do 6 rolls of film per each batch of chemicals or I might be thinking of the E6 kit from a different company. But I think its like 6 rolls per kit.
@kylemccourt663
3 жыл бұрын
I am a film photographer of 35 years and a film photography teacher for the past 15. I really want to try this system but the film that came out during this video does not appear to have a clear base, as it normally should. This would be very problematic when actually wet printing the film in the darkroom and trying to color correct by way of dichroic filtration. Is the film density not an issue because it is being scanned instead? I am super curious about this magical system.
@anthonymiller8979
3 жыл бұрын
I thought all color film (C41 process) has an amber colored base? B&W is usually clear, grey or blue.
@cggg490
8 ай бұрын
after first four rolls, how much time do you adjust developing time thereafter? I’m bad at math.
@loriannx143
Жыл бұрын
Can the washes be reused or only the stabilizer?
@akiray1999
3 жыл бұрын
should I buy the camera or not?
@out1553
3 жыл бұрын
What camera bro?
@akiray1999
3 жыл бұрын
@@out1553 don’t want to go all out, looking at the La Sardina for a cheap but not garbage starter
@anthonymiller8979
3 жыл бұрын
No Photo-Flo is needed before drying or is it built into the Stabilizer step?
@brodie_lienemann
3 жыл бұрын
It’s built in
@lunaartemis5511
9 ай бұрын
Just about to attempt this for the 3rd time to bow see the thermometer don't even go over 86f. So instead of going out on another shoot (as I f***d my film) and starting this. Should of actually just done coursework and not wasted time. The more you attempt this the more you need to purchase. Cba I give up with film. Taken me 2 years to learn how to unload and load a film without buggering it and now just this. So hard doing all this with Dyslexia and discalcula.. just keep getting it wrong 😪
@soundistraveling
3 жыл бұрын
So i can reuse al that developer n blix and stabilizer for more film correct?
@soundistraveling
3 жыл бұрын
And u didnt discard any of it right u saved it for later
@eliasaguirre1227
2 жыл бұрын
Is this legal in Washington state? I’ve heard the chemicals used can’t be bought.
@mstrshkbrnnn1999
6 ай бұрын
This store is in Seattle
@jluc002
3 жыл бұрын
12;30 Perfect
@Boskiiino
2 жыл бұрын
🎥🎞🙌🏾
@jjaylad
6 ай бұрын
You didn't wash your mixer in the video after preparing the developer and before mixing the post development chemicals. Is that OK?
@andyvan5692
2 жыл бұрын
120 degrees for processing?, sure?, as at 100 degrees water BOILS,yet I see no steam!!; just wish you could do a METRIC conversion on these volumes, as since 1966 hardly anyone, esp. in Australia, uses imperial anymore!!
@DeekonJones
2 жыл бұрын
Water boils at 212 degrees F.
@rorycowieson5924
2 жыл бұрын
@@DeekonJones and conveniently in Celsius it boils at 100 and freezes at 0. The system every country in the world except like 7 use.
@DeekonJones
2 жыл бұрын
@@rorycowieson5924 I was simply telling you he wasn’t wrong. Lol
@karl1137
2 жыл бұрын
If he is referring to 120 degrees F, from what I have read C41 process is 100 to 102 degrees F. This may explain the cloudy negatives.
@wack.1151
3 жыл бұрын
arent these toxic? shouldnt you wear gloves or something, from what ive heard :(
@GlazersCamera
3 жыл бұрын
In retrospect, yes, Devin would have benefitted from wearing gloves. That being said, he did not experience any noticeable, adverse effects from not. But still, you should. :D
@adrianvalella6854
2 ай бұрын
bad instructions, no gloves or eye protection, did not clean mixing vessel or stirrer, your negs looked bad also
@dmystify1381
2 жыл бұрын
...do yo have to use a sqeegee thingee...?...asking for a friend..
@Andrew-tt2xs
2 жыл бұрын
Think you can just hang it to dry just make sure u use a weighted clip at the end so the film doesn’t curl up when drying
@mampfi
2 жыл бұрын
No you don't need to. Hard water leaves lime stains on the film, to prevent that you could use the sqeegee thingee to get the water off the film. Many people don't use them because it's easy to scratch the film by using them. There are alternatives like to wash the film with distilled water, use a wetting agent or a salad spinner
Пікірлер: 69