Bro you're literally the MVP for sharing this , wish I found it sooner man, I been messing with mine for about a week now and only got 2 hours ride time on it cause 33 mph ain't enough for my crazy ass
@jjsstreettv5295
2 жыл бұрын
Bro the Words Thank you makes me want to post all the mini bike Hacks.! Keepem coming like this.
@jayjay4536
2 жыл бұрын
I broke my jack shaft bro your a life saver and you saved me some money
@MrRayDupree
2 жыл бұрын
I think I'm going with the straight chain! I don't do much if any off road riding, but dealing with City driving...... Speed is needed more than torque 🤷🏾♂️ 💯
@lordion33
2 жыл бұрын
Thumbs up for being chill af. Love the dog
@jjsstreettv5295
2 жыл бұрын
I Fucks wit chew Bro ....
@Troygehring
3 жыл бұрын
Thanks man it really helped and saved me some money
@teepremesuno121
Жыл бұрын
I believe u can adjust the chain byy sliding the motor down
@OcotilloTom
3 жыл бұрын
Well, that was strange. The video says "full tutorial" but it just quit with the chain hanging on the crankshaft.
@jjsstreettv5295
3 жыл бұрын
If you need more assistance after this higher in mechanic just don't make things stranger. .
@jjsstreettv5295
3 жыл бұрын
I Have a Update Video Here
@rodneypittman101
2 жыл бұрын
Cheetah clutch
@adariushickmon293
Жыл бұрын
Not only you have too take the tourqe converter off too get more speed but when you have a mini bike you can basically make it go as fast as you want it too and once you’ve token the tourqe converter off and have straight chained it you can also take out the governor and take about a few pieces and take out a couple more pieces and then that should make it about maybe 70 or 80 mph fast
@rodneypittman101
3 жыл бұрын
Thanks
@jjsstreettv5295
3 жыл бұрын
Anytime 😊 buddy.
@Blaze-tq5hv
2 жыл бұрын
If you wanted more speed you could’ve changed out the two sprockets in the back part of the jack shaft and get a bigger clutch
@jjsstreettv5295
2 жыл бұрын
I mentioned that in the video....thanks buddy...the full delete is more amazing
@johnadams8305
2 жыл бұрын
Converted my ct200 to a single chain.. with the 10 tooth clutch. What sprocket count do I need?? The 38 from Jack shaft set up is all bad..was Gunna try original 52 I think
@jjsstreettv5295
2 жыл бұрын
The Original CT200U STOCK REAR SPROKET IS 50 TOOTH IF YOUR RUNNING THE STOCK ENGINE WITH GOV DELETE OR BYPASS U SHOULD GET AROUND 4K-6KRPM WITCH is 30-37MPH 5.00 Gear Ratio ✔️. Check Here for your gearing Just play Around with the sproket setting to Figure your Speed Adjustment ⚙️ Ratio ..www.bmikarts.com/Go-Kart-Gear-Ratio-Speed-Calculator
@jjsstreettv5295
Жыл бұрын
Go for it sounds about right.
@rynoyouknow2838
2 жыл бұрын
Took my son's off on his and it does 43 mph with me on it
@fenderbassfan
2 жыл бұрын
You really need a nice tool box.
@909.K
Жыл бұрын
ay bro when u were tightening the chain what were u doing to the back where the sprocket is at? Imma do this to my minibike and need to know if i need to do that too
@smashedbyhashish
Жыл бұрын
Didn't even finish the damn video...
@mogong7260
Жыл бұрын
What's the name of the piece the one you said not to lose?😂
@FxTreasury
2 жыл бұрын
The bolt on the back of the gear system is not coming off for me
@jjsstreettv5295
2 жыл бұрын
You have to use Two Tools to Hold the Rear bolt also while srewing the front bolt out.
@user-sp1dz8ho1y
Жыл бұрын
how Long is the chain? I'm trying to do this but I don't have a long enough chain on mh baja heat
@Joshua_Hammer.777
Жыл бұрын
Is the jack shaft for ⚙️ gear ratio I built a bike jw id like to have more torque
@elijahbrown9482
2 жыл бұрын
I bought mine used and ig the person lost the spacer that goes behind the clutch , could I just use the spacer that’s used for the jack shaft??
@SpAcEcruizer203
3 жыл бұрын
good vid bro i have a 80cc motovox with the gov removed on a 11tooth clutch and 74 rear im getting 40 mph what would i get if i put a 10tooth do i need to change the rear sprocket
@jjsstreettv5295
3 жыл бұрын
Thanks Mane. What I Usually Do Is Change my Clutch to 17tooth but in your case Maybe Try a Smaller Tire in the Rear the Get more Rotation to the gearing you have.
@SpAcEcruizer203
Жыл бұрын
@@jjsstreettv5295 17 oh dam i thought the highest was 15 and the lowest i can find on rear sprocks for my motovox is a 60tooth with the 6 holes but im thinking of getting pocket bike wheels or the 10inch modular ones with the holes in em to run better tires so mad i ordered a 6inch mag wheel from gopowersports brah the quality on there stock tires suck
@robertbruhcuh3634
27 күн бұрын
@@jjsstreettv5295i thought a smaller tire would just slow it down i can’t get my shit taken apart tho so i can’t talk like i know a damn thing
@crackawood
3 жыл бұрын
what's up? what's your max speed now?
@jjsstreettv5295
3 жыл бұрын
I'm clocking at 48-53 Depends the Street.
@crackawood
3 жыл бұрын
oh hell yeah - i just got the camo coleman and was thinking about this and yours is the first video that popped up. thanks bro!
@jjsstreettv5295
3 жыл бұрын
Bro Do it Your Gonna Be impressed On how Much she Picks Up..But may Loose A Little Power in take off but You'll be passing Cars....
@jayjay4536
2 жыл бұрын
My clutch shooting sparks.
@jjsstreettv5295
2 жыл бұрын
Probably Need Replaced... Or Your Chain is Rubbing the Clutch... .
@BigActionFun
2 жыл бұрын
What size did did say that nut was with the cotter key?
@adariushickmon293
Жыл бұрын
And the way how I know is because I have a Coleman bt200x 196 cc mini bike and mine was about 50 or 60 mph fast but then it blowed up so I had too get another motor which is the predator 212cc 6.5 horsepower motor and right now it’s about 50 or 55 mph but it doesn’t feel like it do so too make really actually fast I’m gonna get my brother in law too take out the governor take out a few pieces take out a couple parts and that should make it about 60 or 8 NO matter a fact it should make it about 70 or 80 mph fast
@joshberlin3074
Жыл бұрын
Ay man appreciate the tutorial. I went ahead and did this, but the bolt to the driveshaft and clutch keeps wanting to rotate and slide off quickly while riding since I've flipped the clutch. Have you run into this or have any recommendations?
@joshberlin3074
Жыл бұрын
So I just tried to crank the bolt as you did in your ct200u-ex video, though I find when the bolt is down tight, the clutch seizes, when i loosen it up enough to where the clutch works freely, the bolt holding the clutch wants to fall out. Please Help!
@AMadrigal72
Жыл бұрын
@@joshberlin3074 I'm not an expert but have you thought about using thread locker. It might help, but you will need an impact to get the bolt off after.
@joshberlin3074
Жыл бұрын
@@AMadrigal72 got some one there now been holding for about a week 👍 thanks
@sidewayzmike
3 жыл бұрын
Puppy dog is about to eat your master links! 😁
@jjsstreettv5295
3 жыл бұрын
project With Her Buddy Will Be all night She Has a Private Tool Stash i have to Raid from time to time.lol
@papsprojectchannel
2 жыл бұрын
What's the link for the chain breaker?
@mariametko
3 жыл бұрын
What's the best drive and driven sprocket combination so I can solve the over slack in the rear chain to my Coleman ct200uex ? I'm finding out that this causes bearing problems to the driver bearing. Thanks. Great video.
@jjsstreettv5295
3 жыл бұрын
Well if You want more Top End With Out Stressing a Clutch to Much And Don't Spend To much Money. Go 2 Rear 10 Tooth Jack Shaft Sprockets. To clutch Using The Stock Jack Shaft setup...I Got good Results From that gearing.
@Hxvoc22
2 жыл бұрын
Do NOT do this if you like trail riding! Yes it does go 50 but you lose all your low end power
@jjsstreettv5295
2 жыл бұрын
IF YOU LIKE TRAILING CHECK MY OTHER VIDEO OUT . kzitem.info/news/bejne/2Kqe0X-hpICKhY4 HOW TO INSTALL THE TORQUE CONVERTER BELT DRIVE ...ON COLMEAN OR BAJA. ONLY IF YOU LIKE TRAILING WITH SPEED. 👍
@adamdomonski1619
Жыл бұрын
How much speed you getting and can you still trail ride it
@isaacbrown9855
Жыл бұрын
The top speed for a straight chain on it is like 33, but with the governor swing arm ziptied or taken out it can go up to 39 or 40, and you can still trailride but it would be a little slower pulling out where it has less torque
@sgjesse13
2 жыл бұрын
What are the pros and cons to this set up?
@Deucealive75
2 жыл бұрын
The only benefit is higher road speed. The cons are that you lose all low end. The bike wouldn't work well at all for slow speed off road riding. If riding off road it would struggle and not be able to climb hills that were easily climbed with the jackshaft. The clutch to rear sprocket is hard on the engine and clutch. If you were running the stock engine on the road and started up a long steep hill it would drop all the speed you had.
@sgjesse13
2 жыл бұрын
@@Deucealive75 interesting .. I think I prefer the torque over the slightly higher speed .. we do off road out here … so would torque converter keep torque and add speed ?
@Deucealive75
2 жыл бұрын
@@sgjesse13 Absolutely. With a torque converter you get nice bottom end and the extra top speed. And I would highly recommend a 60 tooth sprocket to go along with the torque converter. That gearing just works better all around than with the 50 tooth.
@troyholland3436
Жыл бұрын
Is a 70 link long enough for the straight chain?
@alanfelix8070
Жыл бұрын
No the stock chain is a 90 link
@WetleySped
Жыл бұрын
I can’t get the bolt off that’s on the clutch. Any help
@youngintrapout6817
2 жыл бұрын
What size chain?
@jjsstreettv5295
2 жыл бұрын
40# Chain
@gucciguwop1981
3 жыл бұрын
How many links did u take off
@jjsstreettv5295
3 жыл бұрын
Like 17 from the Front Jack Shaft chain And Combined Both.
@roeb3872
3 жыл бұрын
Buy a new chain and save the originals , just in case.
@Partnerthedog
3 жыл бұрын
Is it faster or slower on the lower Rpms and what about higher. Any reduction in speed or acceleration or the opposite?
@Partnerthedog
3 жыл бұрын
So this Destroyed my acceleration it barely goes but the top speed is like 50 so guess ima order a 60t rear to get my torque back just wondering if I should go even higher than that to return to normal ratio without a jackshaft.
@angelpatterson8214
3 жыл бұрын
@@Partnerthedog did it work?
@Partnerthedog
3 жыл бұрын
@@angelpatterson8214 yeah so I actually reinstalled my jackshaft because I just love offroad riding, and ordered the 60t rear (stock is 50) and I bought a new chain to accommodate the bigger sprocket I bought a 110 link 420 rk chain for 12$ I had to break it using a punch and hammer and I set it on a small bolt this trick I learned on youtube no special tools. Now with the 60t rear the thing is a monster accelerator. Its down to maybe 23 top speed but man it gets there FAST. like I've owned a kx125 2 stroke motocross bike and when I say the 60t made it accelerate faster I mean it. Looking back, the only mods you need for offroad is exhaust, 18# valve springs, 60t rear and the governor removed. Oh hey, the advanced timing key is a Cheap part and it works with a stock flywheel 3$ upgrade.. and I still really want the ebc grooved brake pads on amazon for 18$. The 60t rear was 35$ and the longer chain was 13$
@Partnerthedog
3 жыл бұрын
Only advise straight chain for on road use only like top speed stuff. Jackshaft for offroad use. But if you ever feel like going 40+ mph the straight chain is the easiest way
@angelpatterson8214
3 жыл бұрын
@@Partnerthedog so the procket fixed ur torque issue without the jackshaft
@javiderek31
3 жыл бұрын
No update?
@jjsstreettv5295
3 жыл бұрын
What's Up Buddy What u need Updates On.? I have time today
@Partnerthedog
3 жыл бұрын
Is it faster or slower on the lower Rpms and what about higher. Any reduction in speed or acceleration or the opposite?
@ShawnPrince
3 жыл бұрын
This video couldv'e been 5 minutes....
@Trumpdumphump
5 ай бұрын
How do you take off the very first bolt that holds the clutch on because mine keeps turning over the engine when I try take it off
Пікірлер: 80