I replaced the starter, relay, battery and fuel pump solenoid... the bike runs perfect now
@darkknight17
2 ай бұрын
What does the fuel pump solenoid do? Why did you change it? Thanks
@briggs9187
2 ай бұрын
@@darkknight17 it did not send signal to the fuel pump when I turned the key to the on possition, it was water damaged, I added dialectric grease to the connector before replacing.
@lukandros
2 жыл бұрын
you can tak out the starter by the left side. no need take the fuel tank... just take the expansion reservoir and the thermostat. PS: as you did on the video ^^
@JT2JZ
2 жыл бұрын
Ya it’s a tight fit but it does sneak out the left side!
@frankstone8930
Жыл бұрын
Next time! Do it from the left side. Remove the cooler tube and there you have the starter. Much less hassle.
@JT2JZ
11 ай бұрын
Did you have to replace any seals or gaskets on the coolant tube? That was my only worry. Didn’t want to be held back waiting for parts.
@dlcarburetor
2 жыл бұрын
Congrats on the find man. Yea looks like old water and oil ingress made the brush/ armature assembly wear. Gets worse from there as it shorts out. Then the smell comes out as the "factory installed" smoke comes out lol
@JT2JZ
2 жыл бұрын
Yup I definitely let the smoke out haha!
@KelsS1k
15 күн бұрын
might change the starter after i receive my ECU from bauce racing but then again i think valve adjustment could fix the hard start problem.
@JT2JZ
14 күн бұрын
I have another video where I checked compression and valve lash on my bike because I thought the same thing! It was almost due for an adjustment. Everything was in spec on my bike still. I think I had roughly 26000kms at the time.
@KelsS1k
14 күн бұрын
@@JT2JZ Damn so it was the starter all along then mmm ok, ima replace the starter myself the easy way thru the wall on the left fairings and coolant draining.
@frankstone8930
Жыл бұрын
Just remove the thermostat on the left so Dr of the bike. The starter is just behind it. You'll save time and your sanity.
@JT2JZ
Жыл бұрын
I did remove the thermostat. Do you mean the hard pipe between the engine and thermostat? That pipe does interfere a bit. I just didn’t want to replace any extra seals or gaskets
@frankstone8930
Жыл бұрын
@@JT2JZwell, no need to remove the tank, the airbox and the throttle bodies. Just remove the thermostat on the left side.
@malicutecutechann_isreal2034
2 жыл бұрын
Very detailed.. my. R9 same problem I replaced everything all brand new. And it’s started perfectly. After I lay my bike down on the right side my bike won’t start. What should I do?
@adilghazanfar519
2 жыл бұрын
I had this issue. My r1 originally had starting issues. I replaced the started and it solve dit Then the bike was stolen dropped then towed laid down on a flat bed. Now it won't start again...
@JT2JZ
2 жыл бұрын
These bikes have a sensor to kill the engine if the bike is dropped so that they do not keep running with no oil pressure. I would check that sensor and make sure the small component inside the sensor is not stuck and moves free from side to side.
@monishchakraborty7277
10 ай бұрын
See it
@user-by5ud2hf1p
Жыл бұрын
I’m having a issue with my Yamaha r1 where it just make a a single click sound when trying to start like a bad starter selenoid but I replaced it and I’m still having the problem. This all started when I replaced the tilt over sensor
@JT2JZ
Жыл бұрын
If your bike is a 2009 or newer good chance your starter is failing just like my bike.
@user-by5ud2hf1p
Жыл бұрын
Yea it’s a 2009 I had a feeling it was the starter since it’s pretty common. Can it also be the crankshaft position sensor because I’m getting a code 12? Or will it still try to turn over with a bad crankshaft position sensor instead of just making a single click sound?
@JT2JZ
Жыл бұрын
What does the code 12 description say? My thoughts if you hear a click that’s the bike sending power through the relay trying to start still. Battery power would be live at the starter So I would still think the bike is trying to start. If the code was the issue I would imagine you would hear nothing when trying to start
@genedoolittle1930
3 ай бұрын
Hey man I know this is an old post lol, mine was throwing a code 12 as well, took the starter out and the brushes were fried. But as for the code 12 I think it just has something to do with the starter not working anymore. I seen another video of a starter replacement and his bike was throwing a code 12 as well. I’ll update after I install the new starter to see if it goes away.
@JT2JZ
3 ай бұрын
@genedoolittle1930 mine didn’t have a code but the starter did fix everything.
@iceman_fox1
Жыл бұрын
If a starter is dead will the bike not turn over at all? Mine it will turn the crank over a time or two and gives up.
@JT2JZ
Жыл бұрын
Check your battery first. If the battery is healthy it sounds like a starter. Mine did the same thing before it completely failed and wouldnt crank at all.
@iceman_fox1
Жыл бұрын
@@JT2JZ thanks man. Yea, the starter is bad
@JT2JZ
Жыл бұрын
No worries. Unfortunately it’s a common issue with these bikes but don’t stress. The job isn’t as bad as it looks
@bootiiii
8 ай бұрын
Just bought a used 09 12k miles… there’s no coolant in reservoir and there’s a leak on the clamp above where the coolant reservoir sits. I also have a starter issue or battery issue… do you have a personal #?
@only_1dhornet
Жыл бұрын
I spy with my eye a supra 😮 in the background sir!! Nice R1 by the way 😁
@JT2JZ
Жыл бұрын
Thanks boss. I do have some older videos on the supra as well if you are into the imports 🤘
@kentcross2757
2 жыл бұрын
Thank you for posting this video! Do you use the stock plugs?
@JT2JZ
2 жыл бұрын
Glad to help. Yes factory plugs are good quality
@crisnmaryfam7344
2 жыл бұрын
Most Japanese applications (Bike and Cars alike) recommend NGK plugs, and NGK plugs happen to be some of the best plugs you can get. Arguably the single best for Japanese engines. Some people swear by their AC Delco or whatever here in American because of their old car (and old wives tales) but many fail to realize those were American engines, and often AC Delco is recommended.... Pop some Delcos in a Honda civic and watch it miss and spit and sputter. Slap some NGK in and then she purrs like a kitten.
@JT2JZ
2 жыл бұрын
Agreed. Use the right plug for the right application. Ac Delco is my go to plug for all my chev trucks but definitely not in my bikes or my Toyota supra. Ngk goes in all my imports
@GettnMr.B3astVID
2 жыл бұрын
I did all this worked for couple weeks.. now whenever I try to start I hear this electrical buzzing coming from the relay and it doesn’t even try to start
@JT2JZ
2 жыл бұрын
I would replace the starter relay if it’s what’s causing your buzz
@ExtraSync
11 ай бұрын
I just swapped out the spark plugs and my bike is still having issues starting up.. not sure what it could be? Bad starter? Bad battery? Or what. ):
@JT2JZ
11 ай бұрын
Battery is the easiest thing to check first. Starters are very common issue though. I also had corrosion in my starter relay connector. That’s another easy check. I have a separate video on that repair.
@ExtraSync
11 ай бұрын
@@JT2JZ the thing is I already replaced those two. Did battery and starter and relay too, spark plugs were the last thing I did. Bike is at 20100 miles rn
@ExtraSync
11 ай бұрын
@@JT2JZ only thing I can thing of is that I wasted the starter while using the bike in the meanwhile. Had to press it like 1-5 times something for it to start
@JT2JZ
11 ай бұрын
@ExtraSync sounds like the starter will be the root cause of your issues then. Only component left. That’s roughly the same mileage when I had my starter fail as well
@ExtraSync
11 ай бұрын
@@JT2JZ what starter should I get? The one I got was a 70-80 one on Amazon.
@andrelucas6590
5 ай бұрын
My 2012 r1 has a similar problem, when the bike temperature rises, the bike have difficulty to start.
@JT2JZ
5 ай бұрын
Likely a starter aswell. They get a lot of heat soak that’s hard on them
@andrelucas6590
5 ай бұрын
@@JT2JZ I'm thinking about make a replacement of the starter. I saw some starters in alliexpress, but I have questions about their quality. Here in Brazil this part is very expensive who prevents the purchase.
@JT2JZ
5 ай бұрын
I bought a cheap starter off of Amazon and it worked better than I expected. Same issue here in North America. Yamaha starters are expensive and nobody had them in stock.
@andrelucas6590
5 ай бұрын
@@JT2JZ Do you now if the starter which you bought is 2 brushes or 4 brushes?
@JT2JZ
5 ай бұрын
I did not disassemble the new starter so I am not 100% sure to be honest. I assume it would be a 4 brush.
@mikee858
2 жыл бұрын
Did you ever get a code 60 error on self diag. After you replaced the starter solinoid, and starter motor? Currently what I am running into. Changed the spark plugs as well
@JT2JZ
2 жыл бұрын
No I haven’t ran in to that issue. What’s the code description for 60 error ?
@Dani-wj7vd
9 ай бұрын
Stesso problema, My R1 2014 55.000km color Matt Grey, cambiato motorino avviamento. Ora very goood! Ma che incazzature prima...
@rellnumbah8245
2 жыл бұрын
Hell Yea! thanks for the update man
@JT2JZ
2 жыл бұрын
Anytime brotha
@jaysonsmith3614
4 ай бұрын
The mk4 👀👀👀
@JT2JZ
4 ай бұрын
Is that a supra!?
@monishchakraborty7277
10 ай бұрын
This models have some serious problem I had one for 3 year it was a pain in the ass
@JT2JZ
10 ай бұрын
I struggled with issues for many years as well
@sypher5136
Жыл бұрын
I have a similar issue but the bike will crank and then sludge hard and then click I’ve already got a new lithium battery new starter and the issue happened again after a week or two slowly honestly have no idea what could be frying the starter or if something else is the issue.
@JT2JZ
Жыл бұрын
Check out my other older video where I found corrosion in my starter relay. It’s a $40 part. Something easy to try anyway
@sypher5136
Жыл бұрын
@@JT2JZ thank you! I will try that.
@AngelCruz-lt7fb
2 жыл бұрын
My bike turns on cold every time once it gets got it doesn’t wanna crank over well it does but super slow not enough to turn on I’ve put new battery two times new starter relay and I’m guessing it’s the starter brushes are bad when hot
@JT2JZ
2 жыл бұрын
Definitely sounds like a starter issue to me. With how hot these Crossplane engines run the starters get a lot of heat soak.
@AngelCruz-lt7fb
2 жыл бұрын
@@JT2JZ thanks mAn gonna order one now I'll keep you
@JT2JZ
2 жыл бұрын
No worries. Ive got a link in the description to the one I bought and have had success with on my bike.
@hankbonner9718
2 жыл бұрын
You burn up the starter by cranking cranking it when the relay was your problem lol am I right or na
@JT2JZ
2 жыл бұрын
Hard to say. I think the starter was weak the entire time causing my issue. My starter ended up failing shortly after putting a massive lithium ion battery in the bike. I think the extra starting power finally caused the starter to completely fail.
@hankbonner9718
2 жыл бұрын
@@JT2JZ either way thanks for the vids I got a 11 raven I'm going to have some fun on in florida this summer
@JT2JZ
2 жыл бұрын
I bet you have some awesome riding in that area! The raven is definitely my favourite colour combo
@LUKEYB0Y93
2 жыл бұрын
@@JT2JZ think I’m having the same issue with my starter. Currently pulling it apart. I’ve got the white, red and silver 09 r1
@JT2JZ
2 жыл бұрын
Very likely. Starters are probably the most common issue with these bikes unfortunately. My new starter is still working great to this day even though it was a cheap replacement. I’m Very happy with it.
@louissmn6965
2 жыл бұрын
Nice vidéo ! What are your bulbs please?
@JT2JZ
2 жыл бұрын
They are just cheap bulbs off of Amazon believe it or not.
@bamboonium1822
Жыл бұрын
Hey I have a question if anyone can answer. I have a 2014 R1 with a new battery. I just had a 16k inspection done on it and had the techs check the starter. Said nothing was wrong with it but I have an issue. The bike starts fine but if I kill it before riding more than 5 minutes it acts like it's dead. Starter will barely turn before completely giving up. If I wait 10-15 minutes, it starts up just fine like nothing happened. Is this due to some sort of design?
@JT2JZ
Жыл бұрын
You definitely have an issue. My guess would be the starter relay or starter it’s self. I had lots of starting issues with my bike over the years. Check for corrosion in the starter relay. Your starter is likely getting weak ( very common issue on these years )
@Frosty-rd6en
Жыл бұрын
From what I gathered, it's a heat ordeal
@georgenegrics4274
Жыл бұрын
I'm having the same issue. When I press start button the relay clicks once, if I keep it pressed it shows code 12 which is cps. My cousin (mb & bmw), and ex motorcycle mechanic said that starter should still spin with faulty cps so it's most likely broken starter motor. Yamaha dealer doesn't have one in stock in any warehouse in US and they weren't able to offer any aftermarket option either..... Your link in the description says it is unavailable. There are few different ones on the net but I'm not sure which one to get..... Any suggestions anyone?! Thx
Try that link and see if it works. This is a fairly cheap option that I have had good luck with. It’s likely not the best quality but I had the same issue. I Couldn’t find a factory starter or upgraded one anywhere. My cheap starter is still going strong today today though believe it or not.
@lukandros
2 жыл бұрын
i did buy a new one, and in 3 months fail. i did send to warranty and is back fine.. im thinking in buy one spare.
@JT2JZ
2 жыл бұрын
That’s unfortunate. Was it a genuine Yamaha starter? Or just a cheap one?
@lukandros
2 жыл бұрын
@@JT2JZ it's between cheap and genuine. The genuine arrives in 3 months. And as I use the bike daily I cant wait that much.
@JT2JZ
2 жыл бұрын
Hopefully mine lasts longer than that. Mine is a cheapy but the bike is parked for winter now. Won’t be able to really test it until next season.
@de-emperor9053
2 жыл бұрын
also my mechnic say a 2008 cbr1000rr starter motoer can work for 09-14 r1, how true is this ?
@JT2JZ
Жыл бұрын
I am very interested if that is true as well.
@de-emperor9053
Жыл бұрын
@@JT2JZ its is true, how he does it only GOD knows. But from the look of things,i think it will work
@JT2JZ
Жыл бұрын
Thanks for sharing. That’s very useful knowledge.
@remydamato6009
Жыл бұрын
Hey bro, I have a 2010 r1 that I crashed back in may and since then I been rebuilding it. I noticed that when I try to start the bike it just cranks and the only way to start it is by push starting it. I have checked my battery, fuses, and all the common things but can’t seem to find the reason for it. Any idea?
@JT2JZ
Жыл бұрын
Starters and starter relay are both common on these bikes. Check the starter relay under the seat. Mine had corrosion in it.
@remydamato6009
Жыл бұрын
@@JT2JZ mine had a little bit of corrosion in the prongs but even with a little corrosion that’s usually what causes it? My r1 has around 16k miles
@JT2JZ
Жыл бұрын
Could be many things but that relay is just one of the easiest / cheapest things to check and replace. I have a video on my channel. My bike wouldn’t crank at all and that relay fixed it. Maybe check the stator if the bike was crashed.
@504palmer
2 жыл бұрын
i have an '06 R1 i am having an issue where the bike cranks slowly and clicks the relay but doesn't start. is this similar to the 09 r1 issue or should i replace the starter
@JT2JZ
2 жыл бұрын
I would start with checking your battery. Those older years are not as common for starter issues
@504palmer
2 жыл бұрын
@@JT2JZ thank you bro
@JT2JZ
2 жыл бұрын
No worries
@juanserrano-mivueltaenmoto
2 жыл бұрын
Lol had the same issue 2 months ago. Had to buy a chinese starter motor. It is working just fine.
@JT2JZ
2 жыл бұрын
Ya mine is just a cheap starter as well. So far so good though. Hopefully it lasts.
@chiwawasv3364
Жыл бұрын
Bruhh hopefully this is what’s wrong with my cbr 600 I hate it my mechanical brain of mine not the best lol 😢 it’s been sitting for some time hopefully nothing else gets bad ahhh I miss it
@JT2JZ
Жыл бұрын
I feel your pain! Mechanical issues can be very stressful. I fought with my bike for nearly a full riding season
@de-emperor9053
2 жыл бұрын
please is the starter motor you got an OEM or aftermarket , also where did you get it from ?, can you share with me
@JT2JZ
2 жыл бұрын
Link is in the description. It’s aftermarket but works like a charm 👌
@JT2JZ
2 жыл бұрын
Fitment and operation is perfect. I’ve been using it over a year now and still no issues.
@iceman_fox1
Жыл бұрын
So after ruling out the starter relay it appears my 09 R1 needs a new starter. I read a comment here that the tank/throttle bodies don't need to be removed and the starter can be removed completely out the left side through where the coolant reservoir normally sits. Do you have an opinion on this? I don't want to give myself more work by trying to do it an easier way lol. I've been wrenching on this R1 for 6 months straight and I'm getting tired of it lol I do love this bike though
@JT2JZ
Жыл бұрын
I know the feeling very well. I had a good year where I spent more time working on the bike than actually riding it. It makes no sense why this bike is still my favourite lol! It may be possible doing it that way but honestly the tank comes off relatively easy / quick and gives you more visibility / light and room to work with. If I were to do the job again I would likely still take the tank off. You could start with the coolant reservoir and take a quick look in at how tight it may be but I personally wouldn’t waist to much time fighting.
@iceman_fox1
Жыл бұрын
@@JT2JZ I agree man. Thank you for the reply. You've helped me in the past on here as well and I appreciate it. I'm mostly a ZX10R guy but I adopted this R1 into my family and I've got a soft spot for it. It's nice having two types of bikes one with a cross plane and one with a flat plane two different animals. The ZX10 makes all the power up top which to me has to be ridden like a two-stroke to stay in the power. Hopefully my issues with this bike will be done after the starter is replaced lol
@JT2JZ
Жыл бұрын
I’m always happy to help out other bikers in the community when I can. Hopefully I saved you some time and hassle. Less time wrenching and more time riding! My bike has been good since the starter replacement so I’m sure you will be too.
@RollinThundervlogs
7 ай бұрын
How’s that new starter motor holding up?
@JT2JZ
7 ай бұрын
Still works perfect believe it or not. I’m surprised considering it’s just a cheap unit off of Amazon
@mike216ism
2 жыл бұрын
How many miles did it have when it died?
@JT2JZ
2 жыл бұрын
Roughly 16500miles
@Shadow0fd3ath24
2 жыл бұрын
Starters and cam chain tensioners are the weak point for sure on this Gen of r1. At least you can bump start it unlike most of my cars lol
@JT2JZ
2 жыл бұрын
Right. I learnt that the hard way. When my starter failed I was 1200kms from home. Not the most enjoyable ride home bomb starting it at every gas station! Cold bomb starts are tough too. Took me probably 4 attempts running as fast as I could for a cold start at roughly 8c ambient temp.
@alexmetzorg9239
2 жыл бұрын
you aint bump starting a R1…
@JT2JZ
2 жыл бұрын
You definitely can when you are forced and have no other options. It takes everything you have running as fast as you can though. Not enjoyable at all! Flatplane r1s start a lot easier bomb starting. My Crossplane was a bi”ch especially with a rear tire that was cold and worn out. It just wanted to skid instead of rotate.
@RageEG
Жыл бұрын
This model fires up just fine in 2nd gear
@JT2JZ
Жыл бұрын
Maybe in a warm climate. Definitely not on cold starts just above 0c*
@9431028d
2 жыл бұрын
What headlight bulbs do you have ?
@JT2JZ
2 жыл бұрын
They are just cheap leds off of Amazon. H7 style bulbs. I think I payed around $40 and they work great. I’ve put roughly 5000kms on this season and the bulbs haven’t skipped a beat.
@mikewazowski1054
Жыл бұрын
I thought about doing the same to my 2013 R1 this winter. Has your R1 been firing up just as strong as the video since you changed the starter?
@JT2JZ
Жыл бұрын
I’m pretty impressed with the cheap starter so far. Since the install it’s never failed to start on me a single time. Knock on wood but all my issues are still fixed.
@mikewazowski1054
Жыл бұрын
@@JT2JZ Thanks! Good to hear, will be doing my starter and plugs this winter then.
@JT2JZ
Жыл бұрын
Good choice. It’s better to do it early and not get stranded away from home like I did!
@ExtraSync
6 ай бұрын
Is ricks Motorsports starter good? My bike is still struggling. ( I haven’t fixed it yet lol, had surgery plus winter so didn’t care) I did antigravity battery, ricks starter, used oem fuel pump, valve adjustment, timing chain adjusted, fork seals and throttlebodies were replaced too (oem) injectors were cleaned and it’s still being a bitch. Will an oem new starter help? Or just waste of money? I don’t know what’s going on and the shop doesn’t either 😤😭 Bike struggled the most on cold starts but when used it’s like a 1-5 tries to turn on. Cold start is like 15-20 times
@JT2JZ
6 ай бұрын
Sounds like you covered almost everything. I wouldn’t replace the starter again, that would likely be a wast of money. Check the starter relay under the seat. Mine had corrosion in it that caused intermittent hard cold starts. I replaced it with a cheap Amazon relay for like $40. Oem is 100ish if you want to go that route. Definitely an easy thing to check / start with.
@JT2JZ
6 ай бұрын
Yamaha R1 Click No Start. FINALLY FIXED! $40 Quick and Easy kzitem.info/news/bejne/spyZv2eZeolpYG0
@ExtraSync
6 ай бұрын
@@JT2JZ I did do the relay too actually, used a cheap one from Amazon, but the shop said it’s good
@JT2JZ
6 ай бұрын
@ExtraSync does your bike have a lot of kms? Maybe a compression check might be a good idea just to make sure the engine isn’t getting tired. While you have the tank off I would ohm out the starter circuit end to end just to make sure there is no high resistance or anything the might affect that circuit. Other than that make sure the battery cca is 280cca at the minimum. These bikes are known to be harder starting even when working correctly so it doesn’t take much for them not to start unfortunately. I wish I had more insight for you.
@ExtraSync
6 ай бұрын
@@JT2JZ it has about 21800 miles. I’m pretty sure they did that. I know they tested the starter and said it was getting its power. And yea I know these bikes are know to be an ass with starting up
@MrYellow225
Жыл бұрын
Is the starter running still no issues? im hesitant between going with the chinese option or OEM
@JT2JZ
Жыл бұрын
I had the exact same fear using a cheap starter but ended up buying it anyway because my dealer could not get one in a reasonable time. I use the bike as a daily driver all summer and have had zero issues so far. It’s never failed to start even a single time. Very impressed with the quality so far considering how cheap it was!
@MrYellow225
Жыл бұрын
@@JT2JZ Thank you so much for the feedback man!! god bless. i kust posted a clip of how my bike behaves. im just hope its not a wire harness issue ):
@JT2JZ
Жыл бұрын
If it’s a Crossplane engine I would bet money it’s the starter and not wiring. They are a very common issue on these bikes unfortunately. I found out the hard way!
@K-carbon
2 жыл бұрын
What mileage is on this bike at the time of the video
@JT2JZ
2 жыл бұрын
26000kms
@JT2JZ
2 жыл бұрын
I have 31000kms now and it’s still going strong after the repair
@credibleglobalservices4118
Жыл бұрын
Does china Motor work well? L
@JT2JZ
Жыл бұрын
It’s still working well for me over a year later 👍
@TheAssassinMT07
2 жыл бұрын
Where’d you get the triple tree from? Is it just a ‘15 triple that fits on there?
@JT2JZ
2 жыл бұрын
I believe it’s stock on the 2012+ bikes.
@TheAssassinMT07
2 жыл бұрын
@@JT2JZ ah okay. I have another question for you, does your r1 make a couple of clank noises when you FIRST start the bike up and then it goes away as soon as it starts? Mine does it and it’s coming from the clutch and my clutch is working fine. I’ve even had a buddy say his r1 did the same on the cold start. Just wanted to know what you thought cause you’ve dove into your r1 a lot more than I have
@JT2JZ
2 жыл бұрын
I think I know the noise you are talking about. Almost like a slight rotational noise and usually goes away after cold starts or if you pump the clutch a few times? Ya mine has a bit of noise from the clutch side as well when cold. I’ve never had the cover off, clutch is still working perfect for me as well so haven’t worried about it to much. My only advice would be just make sure no rattle is coming from the timing chain tensioner on the right side of the bike. Apparently those tensioners are a common failure item as well and usually make noise on cold starts when they are on the way out.
@TheAssassinMT07
2 жыл бұрын
@@JT2JZ glad to know you hear it too lol but nah I don’t think it’s the tension chain cause the engine is running fine I think. I’m kinda having the same problems you were having. It’s having a hard time to start and all of that. BUT I will say that at the moment it’ll pop really bad at like 5000-5500 when it’s hot and I’m cruising or just when I hold the throttle there. I keep getting told it’s my spark plugs going out so I’m hoping that’ll fix it for me. I have a video of it but I can’t send it on here so hopefully you get what I’m saying lol. But if the plugs don’t fix it then I don’t know what else I could do. Maybe tune it but that’s pretty pricey for me right now 💀
@JT2JZ
2 жыл бұрын
ya I try not to listen to close to the raw engine noise on cold starts. These engines are kind of clunky / rattly down low at the best of times. Just listen to the exhaust and nothing else lol If it’s only popping on deceleration at 5000rpm that’s normal on these bikes with the factory emissions air pump and aftermarket exhausts. Mine does it at that rpm as well even with a tuner ( power commander 5 ). If it’s popping or missfire when you are on the throttle that’s definitely not a good thing.
@Shrogunn
2 жыл бұрын
Where did you buy the starter
@JT2JZ
2 жыл бұрын
I was having a hard time finding any starters in stock. I ended up just getting a cheap one off of Amazon for now. It works but not sure how it will hold up In the long run. I spent under $100 so I don’t have a lot of faith in it to be honest. Time will tell. Unfortunately my riding season is over so will have to wait until next season to put some more hours on the bike.
@Shrogunn
2 жыл бұрын
Thanks. I’m having the same issue. But I’m getting the starter, Stator and starter relay all at once.
@JT2JZ
2 жыл бұрын
No problem. Replacing everything is a good idea to save yourself from any future headaches.
@h2opoloplyr
2 жыл бұрын
Definitely a problem. The local dealer was able to get Yamaha to cover it under "recall", so not a single penny was spent by me for this repair. This was like 4 years ago with my 2009 R1. Super surprised they were able to get Yamaha to cover a 9 year old bike (at the time) lol.
@JT2JZ
2 жыл бұрын
Always nice when something like that happens!
@NudaMan
2 жыл бұрын
Ktm does the same thing for bikes older with open recalls 👌🏾 good to know these companies kinda care about us consumers lol
@josesantiagorivera9072
Жыл бұрын
@JT2JZ i hace the same problem with my bike thank you for the video its gonna be more easy than what i was thinking the way you do it
@JT2JZ
Жыл бұрын
I’m glad I could help! The hardest part is not knowing what to expect. Hopefully I saved you some time and effort 👍
@jlamparo8391
2 жыл бұрын
R1 common problem 👍👍👍 starter..
@JT2JZ
2 жыл бұрын
Yes it is. Unfortunately I had to learn the hard way!
@mickeymouse4897
Жыл бұрын
Yamaha make some shit engineering decisions sometimes, no need to bury a service part under shit loads of pipework, Fzs1000 starter is virtually identical in design to the R1, but a 15min job to replace.
@JT2JZ
Жыл бұрын
Ya I do like the fz design for how out in the open everything is! Even simple maintenance like oil changes are twice as fast.
@brycewestervelt9243
2 жыл бұрын
the starter on my 06 went, to buy one was $800 but i got a rebuild kit for $200 fucking yamaha bro
@JT2JZ
2 жыл бұрын
Ya prices from the Yamaha dealerships are ridiculous. The only thing I buy from them are my oil filters. I bought my starter on Amazon for under $100. Probably not the same quality as a genuine Yamaha starter but it’s doing it’s job so far.
Пікірлер: 183