STL Files: www.eclipson-airplanes.com/pa...
Propeller Wall Art: cults3d.com/en/3d-model/art/p...
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmi...
See what else I am working on: / troymcmillan_rc
/ troymcmillan_rc
#3DPrinted,#RCAirplane, #ItFlies
Panthera V2 Specifications:
RTF Weight LW-PLA: 790 grams
Wing Span: 1350mm
Length: 990mm
Panthera Parts List:
2212-13 1400KV Motor: amzn.to/3zQDGhQ
30amp ESC: amzn.to/3zQ0gXO
8x6 Propeller: amzn.to/2VjUDBY
1000mAh Battery: amzn.to/353cLmf
4x 9g servos: amzn.to/31kj82B
2x8mm Screws: amzn.to/3p8gmqY
40mm Foam Wheels: amzn.to/2Ie853O
10x5x3 Magnets: amzn.to/3bzb4Pz
1/8” Wheel Collar: amzn.to/3p4tvl1
3pin wire assortment: amzn.to/3l1xNYt
XT60 connector: amzn.to/3iyZWnf
2mm push rod ends: amzn.to/3nnjD4U
Carbon Fiber Tubes/Rods: www.readymaderc.com
Fuselage: 4x 1.2mm x 1m
Elevator Hinge: 2mmx317mm
Flaperon Hinge: 2x 2mmx500mm
Wing Root: 6mm500mm
Wing Tip: 2x 4mm400mm
3D Printers I use and recommend:
Artillery Sidewinder 3D Printer: amzn.to/396eqIp
Artillery Genius 3D Printer: amzn.to/39cA6CZ
Anycubic Vyper: amzn.to/3rPZ0RN
Anycubic Mega X Printer: amzn.to/3f4oS89
Ender3 V2: amzn.to/2SmLOGk
Twotrees Sapphire-PRO: amzn.to/3wtNOLz
Fokoos Odin-5: amzn.to/3fAES06
3D Printing Filament:
ABS for motor mounts: amzn.to/3xgLI2c
ColorFabb LW-PLA: colorfabb.com/lw-pla-natural
Overture White PLA: amzn.to/3facD9A
TPU: amzn.to/2Sw3Oe8
Tools and Supplies used:
Spektrum DX6 Controller: amzn.to/3l6NFsD
Receiver: amzn.to/3j4PbK4
Battery Charger: amzn.to/3vejwfL
Charge cable: amzn.to/34lOk3q
XT60 connector: amzn.to/3iyZWnf
Assortment of 3-Pin Extension Cables: amzn.to/3l1xNYt
Z-Bend pliers: amzn.to/34mA0rt
2mm push rod ends: amzn.to/3nnjD4U
CA Glue: amzn.to/2J8EvNW
CA Accelerator: amzn.to/3fpbycz
Low-Voltage Tester: amzn.to/2Yk0A0w
Hot knife: amzn.to/3nrCwUH
Drill Bits: amzn.to/3nIJzrx
Hobby Knife: amzn.to/3eYOYJq
#11 blades: amzn.to/3vTJZ2W
Z-Bend pliers: amzn.to/34mA0rt
Build Mat: amzn.to/3vJmauw
Onboard Camera: amzn.to/3rp2OrH
Lead weight: amzn.to/3cFnzeu
LW-PLA Print Settings:
Quality:
Layer Height - 0.25
Initial Layer Height - 0.15
Line Width - 0.4
Walls:
Wall Line Count - 1
Z Seam Alignment - User Specified
Z Seam Position - Back (Position part to align Z seam)
Seam Corner Preference - Expose Seam
Top/Bottom:
Top Layers - 0
Bottom Layers - 0
Infill:
Infill Density - 0
Material:
Printing Temperature - 235
Build Plate Temperature - 60
Flow - 55%
Speed:
Print Speed - 100
Outer Wall Speed - 55
Inner Wall Speed - 55
Travel Speed - 120
Travel:
Enable Retraction - Checked
Retraction Distance - 7.5mm (Bowden Tube Ender3)
Retraction Speed - 35mm/s
Retraction Extra Prime Amount - 0.2
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 80
Mesh Fixes:
Union Overlapping Volumes - Checked
Special Modes:
Surface Mode - Normal
Experimental:
Slicing Tolerance - Middle
Music:
Joakim Karud:
KZitem: / joakimkarud
Soundcloud: / joakimkarud
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!
Негізгі бет Ғылым және технология Complete Build Guide and Flight - New Panthera V2 by Eclipson
Пікірлер: 138