Youre such a humble dude. 1st video ive watched of yours. Im going to watch the rest now.
@kikemotors6138
3 жыл бұрын
Thanks man I appeciate it! I got plenty more coming just have to edit
@mammonco
Жыл бұрын
Looks like special tools to me
@richardtschida2321
2 жыл бұрын
Impact screw driver for use on difficult screws
@michaelrocha7351
3 ай бұрын
Brooo my flywheel was rusted out I had another engine so tried to put that engines flywheel and stator on mine but the lil pin to aim you flywheel like the crankshaft lil pin it broke off so now the flywheel is on but the crankshaft is moving but the flywheel isn’t help me out.
@kikemotors6138
3 ай бұрын
It still should technically move even with out the pin but if your saying the pin broke then you just andswered your own question take it off again and put a new pin you can buy them at ace hardware and reinstall it.
@dpeter21a52
2 жыл бұрын
Do you respond ? So I was cleaning out my coolster 125cc and I spun the stator now my bike starts but won’t idle
@kikemotors6138
2 жыл бұрын
If it won't idle check your carburator has two Jets a pilot jet and main jet one of those could be clogegged if not get a new carb it's only like 20$ on Amazon shouldn't be a difficult fix mine was doing tht too if u check out the next video
@readylucas
2 жыл бұрын
My stator cover wont stay on.. threads for top bolt are stripped so it wont even screw in. any advice?
@daddyguy29
Жыл бұрын
Get rethread kit
@fwkxnny
2 жыл бұрын
what jaw pullers are you using? i went through so many different ones and can’t find the right one.
@kikemotors6138
2 жыл бұрын
The pulley puller ? Or the little black beaker bar?
@Luisperdo
8 ай бұрын
It is called magneto flywheel puller
@Luisperdo
8 ай бұрын
Im in the middle of doing this as well just replaced the coil,spark, cdm and something else also carburetor and still no spark so hopefully ill get it running next week good video thank you
@bikersoncall
2 жыл бұрын
My stator plate is stuck after removing the two bolts, it will spin side to side with a hammer about 1/4'' but doesn't seem to want to be removed.
@kikemotors6138
2 жыл бұрын
It's prolly holding on by the rubber o ring? If not the wood stuff key isn't in the way?
@bikersoncall
2 жыл бұрын
@@kikemotors6138 Thanks man, I got it off finally , yeah it was the o ring, makes it confusing as to whether there is something else.., I pried and worked the plate back and forth, then it came out, and oil pissed out all over the dining room floor at burger king. :]
@badassgrower
2 жыл бұрын
Thanks man !!! Mine just took a shit!!!! Did yuu get her running? Hope so
@kikemotors6138
2 жыл бұрын
I sure did watch the other videos!
@ChoppaBoyDyl
2 жыл бұрын
Bruh this video caused my friend to break the rim around the fly wheel you may have gotten lucky but people do no need to be out here doing this I was showing him the right way then he seen your vid and decided he would try that when I was getting it off right, now he’s got a giant hole in the aluminum above the stator
@kikemotors6138
2 жыл бұрын
Sorry man I hate to hear that but I mean this is kinda at ur own risk obviously not the right way u can do it and I think it's conmen sense to not put to much pressure. Im not a professinoal but I mean it worked for me and other ppl🤷🏻♂️
@connorjack3246
2 жыл бұрын
What oil should I use in a 125 pitbike??
@kikemotors6138
2 жыл бұрын
I think it's 10w30 if it's a 4 stroke if not google the model with specs and oil type and that should say
@nwee5758
Жыл бұрын
What's that thing your using to pull the stator off?
@kikemotors6138
Жыл бұрын
Crowbar
@williamgilbert3884
3 ай бұрын
A puller 😂
@hunterhanlin7539
2 жыл бұрын
Quick question, can I run my bike without the stator cover?
@kikemotors6138
2 жыл бұрын
I think u could,it just covers the flywheel from spinning and hitting your foot.
@hunterhanlin7539
2 жыл бұрын
@@kikemotors6138 Ok thanks couldn’t find any answers anywhere.
@saxondigman7041
2 жыл бұрын
You can but very bad idea as liquids and shit can get on the stator and other parts which will make them dirtier and rust.
@hunterhanlin7539
2 жыл бұрын
@@saxondigman7041 yea just was working on my bike and wanted to take a quick ride until I get my cover.
@young610scrooge
6 ай бұрын
@@hunterhanlin7539don’t do it.. mines came off and i got caught in the rain now my shit won’t start 😂
@galvez7911
11 ай бұрын
The 9/16 nut on my stator is stuck i cant unscrew it or anything? Any help?
@kikemotors6138
11 ай бұрын
Cut a line thru it with a cut off wheel and take it off with a flat head
@galvez7911
11 ай бұрын
@@kikemotors6138 i got the 9/16 nut off but now the threading is stuck inside with the stator & i have no crowbar lol any help?
@fatsomustang9433
2 жыл бұрын
My coolster stator don’t work where did you buy it?
@kikemotors6138
2 жыл бұрын
Amazon or eBay just make sure the conector is right and wire colors
@SarTakeOver
Жыл бұрын
How do you even find the right part bro? I just bought a 2016 and I can't find the right parts 😭🤦🏾♂️
@kikemotors6138
Жыл бұрын
A lot of research and comparing the two especially with them being chinease bikes they make so many diff aftermarket stuff for them
@SarTakeOver
Жыл бұрын
@@kikemotors6138 yeah I been looking for parts for the last month I just been returning parts and buying new ones non stop Thanks for the response appreciate it
@kikemotors6138
Жыл бұрын
@@SarTakeOver make sure to match it up with the wire colors becuase a lot of the the time it will say fits a 2001-2020 125 and it's not the same lol. Also the check to see if it looks exactly like it
@jackas1583
Жыл бұрын
3 tools you used costs total over $30 new. Flywheel remover tool only cost $7 on amazon. Lets not talk about the labor. Be smart. Your process have a 50%+ chance of damaging parts. GO FIGURE
@Dani-be2wl
Жыл бұрын
Go figure ..It worked for me 😂 talk about being smart then why are you watching ... The guy even said whatever works for you not to go running and do it , everyone has different techniques.
@kikemotors6138
Жыл бұрын
Thank you! I even say I'm no professional but if u wana get back on the road u get clever ideas just don't be dumb and force anything to much that u know will break
@anthonyclark5055
3 жыл бұрын
How do you unlock a back tire on a coolster 125 pit bike
@kikemotors6138
3 жыл бұрын
I would assume the wheel axle bearings are bad it shouldn't lock also if it's on gear maybe and not on?
@youhadyourchance
3 жыл бұрын
Put it out of gear?
@kikemotors6138
3 жыл бұрын
@@youhadyourchance as in nuatral
@Coop3x
2 жыл бұрын
Yea if your in gear when u try to roll it it’s gonna lock up on you so make sure u click it all the way in nuatrual
@FTNDrew
Жыл бұрын
Bro this is horrible advice😭 buy the magneto pullers online. Tusk sells a set of 4 which will fit all bikes for cheap. You’ll be having kids breaking their bikes tryna pull a magneto off with a crowbar. You wanna be helpful then push people to get the right tools for the job instead of doing that cringy shit. You can’t be a mechanic without tools, so have the right tools.
@kikemotors6138
Жыл бұрын
Yes I understand but I think I said that in my video it's for ppl that don't have money or the right tools. If you have the money obviously I'd get them but not everyone does and where r there's a will there's a way.it's kind of obvious though on how much pressure is fine and is not.
@marte1a256
2 ай бұрын
Leave him alone idiot he’s just throwing ideas out there. You can either take them or leave them.
Пікірлер: 54