Great review! I learned more about this printer in the last 22 minutes watching this video than I have watching several hours worth of the other videos. I bought the K1 MAX about 3 weeks. I printed several jobs with the white Hyper PLA with no problems. I switched filament to the black Hyper PLA, and the filament jammed in the heat sink right above the hot end. Unfortunately, you have to completely disassemble the carriage by removing the extruder, front fan and circuit boards, the hot end and the heat sink to clear the jam. I did this three times in a row and finally switched back to the white Hyper PLA with no jamming problems. Not 100% sure of the issue. Looks like maybe over heating. Next test I do I will confirm that the top lid is off the chamber. I will also set the hot end on the lower end for temperature for PLA material. I normally run at 220, but may drop it to 200. I sure hope this fixes the jamming problem. I have a lot of ideas for things that I want to print, but only being able to print with the white filament is slowing down my production. Great job and thank you for sharing this information.
@Rcschim
Ай бұрын
Thanks for the nice comment! Weird that you had so much issues with the other pla (same brand?) On my flashbi had a lot of jams, until I realized you shouldn't mix different materials in the same nozzle. They suggest you buy a dedicated nozzle or different material, but this is ok here because of the hotswap nozzle
@MCsCreations
5 ай бұрын
Fantastic review, Mario! Thanks!!! 😃 This is the 3d printer I'm going to buy, no doubt about that! (The only doubt is when. 😬) Anyway, stay safe there with your family! 🖖😊
@luisrincon2146
4 ай бұрын
Hi Mario, finally wich is better, creality k1 max o flashforge m5 pro?
@Rcschim
4 ай бұрын
For best possible quality I chose the flash. But over all I’d say the k1 max since it haha better build volume, better software, more reliable webcam and network (that’s driving me crazy on the flash).
@TFSR_ImPuL5es
5 ай бұрын
I am on the verge of rooting my K1 max but I have some unanswered questions all is well and good that I can access remotely to print, but is the screen still able to be used to print in person? This is one of the only things stopping me from going down this path, any advice would be great.
@Rcschim
5 ай бұрын
Yes, the screen works exactly as before. The only difference I guess is that he doesn't tell me each step (wipe nozzle, levelling,...) in detail.
@TFSR_ImPuL5es
5 ай бұрын
@@Rcschim so long as my wife can still print things on her own while I am away with work that is all I need. Thanks for the quick reply.
@webpro607
4 ай бұрын
Creality will release a new printer (K2 Max) by end of June/July
@jonscot8393
4 ай бұрын
Hi Mario, Whats the best mini quad filament to use? Tough-PLA, Polycarbonate Filament or ASA.
@Rcschim
4 ай бұрын
for wich part of the miniquad? for the arms? body? or just for gopromounts? I only printed TPU for the mounts on quads... So far I didnt print parts that were super rigid. I guess ASA or Nylon are quite stiff?
@adambartlett7087
5 ай бұрын
This may be a stupid question, but with a stock printer running stock firmware, is the LIDAR sensor active? I ask this as I have never seen any red laser. Coming from it.
@Rcschim
5 ай бұрын
haha, I also didn't see much laser - but then realized, these options are off per default ;) check in the settings, under camera, there are some LIDAR options (I have a screenshot in this video) but what I see from other reviews at least a few months ago it looked pretty half baked. Especially the motion advance calibration (where it prints a zig zag pattern and measures this with the lidar) is not really beneficial for print quality.
@Ronoaldo
3 ай бұрын
Amazing Review! I have one too and can you kindly answer this: when you printed TPU did you used the side/back spool holder or another method? Thanks!
@Rcschim
3 ай бұрын
Side spool that you saw me printing on this vid
@rctips1763
5 ай бұрын
Thank you for all the technical tips! I learn a lot and my Ender 3 KE is arriving today (have the same software...)
@Rcschim
5 ай бұрын
Thanks, I also have 2 videos about the Ender 3 ke... have fun with the printer - it's a nice device!
@danielhimle7617
4 ай бұрын
hello :) do you have any idea what version your K1 max is? V1- V2 or V3?
@Rcschim
4 ай бұрын
honestly: no ;) at least I saw it's not the one with "unicorn" nozzles. the firmware on it was from July 2023 - so maybe it was a V1?
@maccam666
5 ай бұрын
Cool 👍
@_neto7
4 ай бұрын
Really nice video! What spray glue did you use?
@Rcschim
4 ай бұрын
It's called 3dlac
@ThomasKing0517
2 ай бұрын
Great review!
@leickenberg
5 ай бұрын
I'm in the market for a large volume printer and have been looking at the K1 Max for a while. What's your experience with VFA? Has this improved with the latest update? Were you able to address this?
@Rcschim
5 ай бұрын
I didn't do beauty prints. Need to test this more. Shouldn't be a problem for this printer imho. Will update you here in a few days
@leickenberg
5 ай бұрын
@Rcschim thank you appreciated 😊
@Rcschim
4 ай бұрын
Printed the orca vfa test today: from 80-300 in 20mm steps: Severe at 180mm/sec on 60degree 80,100mm on most directions On error on 300mm at 45 degree Overall quite nice results considering the speeds. More vfa to be seen on low speeds.
@leickenberg
4 ай бұрын
Thanks for checking this, I ordered one anyway - der Preis war heiß 😉
@leickenberg
4 ай бұрын
I have received the printer and STRONGLY advise against getting one: quality control is non-existent, print quality is worse than my €250 printer, many failed prints, maintenace is a pain in the back and it's not noisy, the noise levels are infernal. I can't share your enthusiasm unfortunately.
Пікірлер: 30