Hello from New Zealand. Mine is a 2012 Spanish Nissan Navara D40 St-X Can set everything to top dead centre then remove head then replace head again?. Thanks for your video?.
@AjusaAutomotive
8 ай бұрын
hello again friend! It can be done as long as the synchronization does not change. Best regards
@jimsalo2241
2 жыл бұрын
big likes on the blue bolt stretcher wrench 👍🏻👍🏻👍🏻
@AjusaAutomotive
2 жыл бұрын
Thanks for your comment!
@mausmausinger1
6 жыл бұрын
Hi according to Nissan manual : CYLINDER HEAD INSTALLATION 1. Apply engine oil to bolt threads and seat surfaces. 2. Tighten bolts to 35 to 44 N×m (3.5 to 4.5 kg-m, 26 to 32 ft-lb). 3. Tighten 180° to 185° [target: 180°] (angular tightening). 4. Loosen completely to 0 N×m (0 kg-m, 0 in-lb) in the reverse order of that shown in the figure. 5. Tighten bolts to 35 to 44 N×m (3.5 to 4.5 kg-m, 26 to 32 ft-lb). 6. Tighten 90° to 95° [target: 90°] (angular tightening). 7. Tighten another 90° to 95° [target: 90°] (angular tightening and apply ONLY engine oil . With differente lubrification you will change torque parameters. Greetings from a german master technician
@AjusaAutomotive
6 жыл бұрын
Hi! Thanks for this great information. Both tightening procedures are very similar. Our third stage (-90º + 4 kpm) means completely loosen and tighten again, one by one. You can find more information in our Facebook facebook.com/AjusaSpain/ and in your Twitter twitter.com/Ajusa_Spain. Best regards
@robotech1990
6 жыл бұрын
I was looking for this procedure . thanks a lot . Cheers from Chile.
@AjusaAutomotive
6 жыл бұрын
Your very welcome!
@tulioalfonzo9343
4 жыл бұрын
Buenas noches no lo tinen en español
@conmanumber1
9 ай бұрын
Hello from New Zealand. Mine is a 2012 Spanish built Nissan Navara D40 St-X Can I set everything to top dead centre then remove head then replace head again?. Do the radiator need removed?. Cheers Carl Gin
@ingkittv
Жыл бұрын
nice watching frend
@AjusaAutomotive
Жыл бұрын
Thank for your comment!
@sara78130
8 жыл бұрын
BEST THANKS
@carlosguzman5856
3 жыл бұрын
Hola muy buenos sus videos, gracias por compartir, como se llama el instrumento que ocupa para medir el desgaste del bloque, gracias saludos.
@AjusaAutomotive
3 жыл бұрын
Hola Carlos! Se trata de una regla recta calibrada y una galga de 0.05mm espesor. Un saludo 🖥️ facebook.com/AjusaSpain 📸 instagram.com/ajusa_automotive/
@danielv2114
Жыл бұрын
hola colega muy interesante tu video tutorial agradecido de que des a conocer tu saberes con la comunidad sobre este armado,yo hize el mismo trabajo pero resulta que al arrancar la camioneta esta anda mal en ralenti y tiene una fuga de aceite que viene de donde esta el depresor y la tapa de distribución , antes de desarmar el motor no la presentaba pero al momento de echarla a andar con la culata reparada fuga constantemente aceite por esa zona que mencione , mi duda seria si podría ser el nano reten que trae en la culata entre la tapa de distribucion y la culata . saludos cordiales
@AjusaAutomotive
Жыл бұрын
Hola Daniel! Muchas gracias por su comentario. Respecto a tu pregunta, sí podría ser por la zona que comenta. Un saludo
@matumbwesam697
3 жыл бұрын
What is the defference betwene ayd25 with water to that without water
@AjusaAutomotive
3 жыл бұрын
We are sorry but we have not understood your query. What do you mean exactly?
@azmizai7225
Жыл бұрын
Kedai di mana bos?
@AjusaAutomotive
Жыл бұрын
helo! Tanya di kedai alat ganti terdekat anda. Semua yang terbaik
@zamzam4372
6 жыл бұрын
My nissan navara 2.5 wont start after done top overhaul. Please give some advise
@AjusaAutomotive
6 жыл бұрын
Hi! It could be the synchronization or the injector pump incorrectly configured. You can find more information in our Facebook facebook.com/AjusaSpain/ and in your Twitter twitter.com/Ajusa_Spain. Best regards
@zamzam4372
6 жыл бұрын
Ajusa how can i fix it?
@AjusaAutomotive
6 жыл бұрын
You have to set up the timing again, as we show in the next url : kzitem.info/news/bejne/1Gxjl2Z4fl-Yp6Q Best Regards
@zumirobi1
5 жыл бұрын
ти забил поставить рейку Common rail. :) Щас должен снять воздушной коллектор
@jesusibarra3296
Жыл бұрын
Disculpa una pregunta cuanto llevan de torque las tapas de los árboles de levas
@AjusaAutomotive
Жыл бұрын
Hola Jesús! El torque es de 2kpm. Un saludo
@borongansj
5 жыл бұрын
what kind of grease you have applied? thank you.
@AjusaAutomotive
5 жыл бұрын
Hi! It's copper grease, but you can use motor oil instead. You can find more information about AJUSA in our Facebook: facebook.com/AjusaSpain and in our website: twitter.com/Ajusa_Spain. Attentively
@martinchakulya9041
11 ай бұрын
What happens when the chain snappet to the head cylinder i.i need to replace the vaive or not for us 25 nissan navara
@martinchakulya9041
11 ай бұрын
Help ples
@martinchakulya9041
11 ай бұрын
Help please
@AjusaAutomotive
11 ай бұрын
We're sorry but we can't help you. We recommend you contact your trusted mechanic. Kind regards
@bertfromnz9069
2 жыл бұрын
Hello - your head torque values are incorrect - it is 39nM then 180 angle - loosen to zero- then 39nM +90+90 degrees
@AjusaAutomotive
2 жыл бұрын
Hi! The torque values have been taken from the workshop manual, thanks for the contribution. Kind regards
@cesarurquizo8737
Жыл бұрын
Cuál es el nombre de esa regla y en dónde la consigo?
@AjusaAutomotive
Жыл бұрын
Hola César! Se trata de una regla normalizada y puede adquirirse en tiendas de herramientas para talleres. Un saludo
@adolfoalarconvasquez9388
3 жыл бұрын
Un saludo ala escuela de mudos.no aga enseñansas sin ablar.gañsn
@AjusaAutomotive
3 жыл бұрын
Hola Adolfo! Nuestros vídeos no incluyen audio porque se visualizan en muchos países. Realizamos el montaje paso a paso para que quede bien explicado. No obstante, si todavía le quedan dudas, puede dejarnos un comentario o contactar directamente con nuestro departamento de asistencia técnica: asistenciatecnica@ajusa.es Por cierto, nuestros nuevos vídeos ya incluyen música, esperamos que le gusten más ;) kzitem.info/news/bejne/uKqCrmGiq4uhd6Q
Пікірлер: 42