The cardboard trick is genius. You learn something new every day you use for the rest of your life! Thank you!
@RichpinTv
Жыл бұрын
You are so welcome!
@RodknockRhett
4 жыл бұрын
Before you buy a new one, try unplugging the connector and plug it back in. I just did that and my completely dead blower motor sprung to life. It works on all settings including the 3rd one which hasn't worked in over 2 years! Definitely try replugging it first.
@anyuser5022
4 жыл бұрын
Today my fan stopped working, I Googled the problem, got this video, it was exactly what was wrong with mine, I followed it step-by-step, and my fan works now. Thank You ☺☺☺
@jimmcneely8691
5 жыл бұрын
I've had an on-going problem with my 01 Dodge Dakota for years. This is by far the best video I've come across to remedy the problem. Dodge has a problem with their HVAC system and should offer owners a recall repair. Until that happens, I'm glad that there are videos like this to help owners who may not always have the money to pay outrageous dealer fees for repairs.
@KSmove
2 жыл бұрын
M.
@dhanshel
9 жыл бұрын
Thanks for the video brother. An expensive trip to the garage just turned into a $12.00 bargain. Took only about fifteen minutes. Much appreciated.
@jimmcneely8691
5 жыл бұрын
UPDATE! February 10, 2019: I looked at your video again and saw the part where you first banged on the blower motor a few times. I never have, so, I did, and voila! It started running! It appears that there is a loose connection in the wiring there, which should be easy to fix! THANK YOU for your great video, you saved me a ton of grief! Just goes to show you, check the simple things first, you just might find a quick and easy solution!
@noahbyrd5440
4 жыл бұрын
Great video very explanitive and helpful, additionally you kinda sounds like Ray Ramano 🤣
@ginocastellino865
Жыл бұрын
Thanks so much for this very easy to follow video, I first tested my blower motor just the way you did and it ran fine,then replaced the resister and everything runs great with all speeds! You saved me a big bill at a shop! Thanks!!
@designertjp-utube
Жыл бұрын
Agreed. Wonderful Helpful Video. I may go straight for the jugular and replace my resistor too. This could have been the sharp electrical burning smell I smelled once (coming thru the inside cabin air vents) in my Dodge Dakota 2004 Truck. My Blower Fan only goes full blast or not at all. At least I can still turn it off.
@rickloeralends
7 жыл бұрын
Just installed a new resistor on my 2004 Durango. Your video helped me find out the problem and get it fixed!!Thanks for your video!!! Two thumbs up! God bless
@carlanderson4610
3 жыл бұрын
Thank you I watched your video and fixed it my second pin was getting hot and melting the plastic. Thanks again
@INeverWanted2010
7 жыл бұрын
Hey - thanks a ton for this video. I know next to nothing about cars but you explained everything so well that even I was able to replace this part in my truck, all by myself even! The kit cost me $15 and works perfectly and I couldn't be happier.
@RichpinTv
7 жыл бұрын
I am glad i could help.
@jeremygriffin3758
6 жыл бұрын
Thanks for the video...I almost ordered a 40 dollar blower motor but luckily i watched this video and checked my resistor first and i had the same issue in my 02 durango!
@brianw7841
6 жыл бұрын
Dude i got an 02 durango. Had it since 05. That resistor and harness keep melting. At least once a year i put a new one in. Cant figure out what the issue is. About to put a new blower motor in. Pretty sure thats not the issue but for a little money. Fk it.
@mototoad1242
3 жыл бұрын
@@brianw7841 did it fix it for good? My blower motor works but only after I slap it lol
@mack1659
9 жыл бұрын
Thanks for the video, my connector was stuck due to over heating, so I gave it a bath in WD40(Wires end up) and it popped apart after and hour in the bath, good tip about the motor, will explore.......OBTW my resister replacement was $8 from Autozone......
@teddysmith1083
5 жыл бұрын
Thanks this helped saved me from buying a new blower saved me like $110 bucks mine wasn't as bad as yours it was just a resistor 12 bucks at O'Reilly's
@joshuabrown3525
5 жыл бұрын
Thank you so much! I have a 2001 Dodge Dakota Sport V6 4 door that had this problem. Your step by step video just saved me a ton!
@captainhowdy1595
2 жыл бұрын
Thank you! My neighbor just had the exact same problem. Cut my time in half on diagnosis thanks to your video. They just had a loose wire. Keep the good videos coming brother!
@janedoe8225
5 жыл бұрын
This video is exactly what I was looking for. My fan in my 2001 Durango just stopped one day. Checked both fuses, fine. Next I'll be doing this. Thanks
@karinjackson6702
2 жыл бұрын
Good, simple, easy explanation. Covered everything I believe for testing. Good job. Thank you.
@RichpinTv
2 жыл бұрын
Your welcome.
@DadDoingStuff
9 жыл бұрын
Thanks a ton. I thought a new resistor was going to solve the problem, but it was also a totally corroded connector. I can make it work if I wiggle or hold it in the right spot. New connector on order should completely resolve. Thank you for posting such an informative video!
@billg7205
7 жыл бұрын
22 dislikes. Wonder if those people know how much effort goes into making a video like this with dual screens, that clearly shows all the locations being worked on.
@beckymuro5046
6 жыл бұрын
Code 3 4 5 10 Dodge Dakota Sport V6
@janedoe8225
5 жыл бұрын
They're the type of people that dont work on their own vehicles.
@jimmcneely8691
5 жыл бұрын
So far there have been 64 dislikes as of February 10, 2019. I guess those people want him to repair their vehicles, for free?
@dennyhyer5243
6 жыл бұрын
Mine stopped blowing air altogether. No matter what setting you click it to . I'm glad I watched this video before spent hundreds at a garage diagnosing it.
@donlaguilles985
Жыл бұрын
This video gave me confidence to fix my own Durango. To bypass the testing, well, I'll just replace the resistor, the blower and the fuse. That should cover it.
@scootrose
8 жыл бұрын
Thank you so much for posting this video. I knew something strange was going on because it would work on low but if you increased the fan power it would completely shut down and low wouldn't work for a period of time. I couldn't unplug so i assumed it was bad like yours. I took a picture after I removed it (yes the left screw was a problem @Dave W).
@TheWwong
10 жыл бұрын
Hey Rich, Thanks to you and your review of the Mastech multimeter I purchased the same model and have been very happy with it. Thanks for posting.
@RichpinTv
10 жыл бұрын
Glad you like it.
@tradetalk7307
4 жыл бұрын
thank you for your very helpful and instructional video, and i also must add that you sound just like peter, from family guy. not trying to disrespect or offend....
@theguyinmaine
5 жыл бұрын
My Durango looks just the same, burnt plug. My last Durango, bad resistor, plug was ok. Cheap easy fix. Good video.
@VQ35er
9 жыл бұрын
Hey Thanks a million! The exact same corrosion problem on mine. Just wiggled enough green stuff out of the connector to make the blower go until the weekend, Junkyard time!
@BlackHistoryReview
22 сағат бұрын
Well-done video. About to try mine now. Thanks!
@Domestic_Hadouken
10 жыл бұрын
Hold on to your hat! Haha good job, im learning a lot from your videos thanks rich :)
@zx8401ztv
10 жыл бұрын
Smashing diagnostics and repair :-)) No wonder it didnt want to work lol, i bet the old resistors were ok, just dampness killed the connectors, thank god it was nice to get to :-))
@robkelley1882
Жыл бұрын
You just saved the day my friend. Thanks a bunch!
@RichpinTv
Жыл бұрын
Glad to hear it!
@curtishouze1471
6 жыл бұрын
I enjoyed this tutorial. It was very informative. Thank you sir!!!
@webslinger2011
10 жыл бұрын
Hi! Thanks for posting on how to test for the blower and resistor. Bought a k11 micra that sat for two and a half years. Got it running but the AC blower did not work but still has gas in it. I'm gonna fix this next.
@MrDbertrand
2 жыл бұрын
thanks for the great tips. Did they design these things to all die horribly with corrosion/heat?
@james-im1sj
5 жыл бұрын
Nice you saved me alot of wondering have the same issue we found fuses were all good and blower working but never thought of this being bad I'll be checking this tomorrow 🤙 Thank you
@palmerstile9379
Жыл бұрын
Awesome video, this is how you should make mechanical vids on youtube!
@RichpinTv
Жыл бұрын
Wow, thanks!
@MrTibbz83
9 жыл бұрын
just hopped under my dash .... same issue I cleaned mine up and it's back working again thanks
@elguero7385
6 жыл бұрын
Great video very informative thanks a lot man i fixed mine right after your video mine was smelling like burnt plastic rite before it gave out
@coledarnold3679
2 жыл бұрын
Thank your so much. Helped me get mine working again
@coleslaw4268
4 жыл бұрын
I just unplugged the power to the blower motor and plugged it back in and it works great again!
@smaguns1
8 жыл бұрын
Thanks a bunch for the simple instructions and demonstration! Awesome
@eddienevermind6541
5 жыл бұрын
Great useful video, trying to diagnose my 03 Durango right now
@bradharris8935
8 жыл бұрын
Awesome video. I will be trying this later today/tomorrow. My AC blower quit working all of a sudden this morning. :(
@xChromerSatanasx
3 жыл бұрын
You're a good teacher
@Nobody-by5rs
9 ай бұрын
This is very helpful. Thank you!
@RichpinTv
9 ай бұрын
You're very welcome!
@robertg5437
5 жыл бұрын
good video..my 2003 similar,,, tested the fan, and it was the usual resistor,which went out in a puff of smoke...Thank YOU
@DmytroYatskov
6 ай бұрын
Same problem, same solution. Thank you
@LSJUAN
10 жыл бұрын
Check the the drain tube for the hvac box. Chances are it's clogged and it's filling the hvac box with water. Blow the tube out with compressed air
@RichpinTv
10 жыл бұрын
I will check that.
@johnsquires911
5 жыл бұрын
Perfect video, exact same problem I have including the plug. Thank You
@joseminchoca477
4 жыл бұрын
Thanks for your videos help me out a lot
@riptantorn5337
9 ай бұрын
Bloah motah haha love that accent and thanks much. Video was a great help
@brandonbattle7434
8 жыл бұрын
I really don't feel like doing this I'm just glad it's an easy fix
@michaelhudspeth
5 жыл бұрын
I had the repair first done at a gas station for about 350. Ever since I have done it myself. I guess a bad design by Chrysler. Same resistor and wiring plug has failed probably 5 or 6 times since. Blower motor always tests okay. Have to be a contortionist to reach and unscrew the resistor but otherwise a simple fix. Dorman sells both resistor and plug together. Don't just replace the resistor if the hot pin is burnt. Replace both resistor and plug at the same time or the resistor will fail within a month. Doesn't appear to be a moisture issue as the car is in Southern California.
@anthonynelson9136
4 жыл бұрын
The resister replacement is a quick and dirty car lot fix that doesn't solve the real problem. Usually, the blower motor is drawing to many amps and overheating the resistor and the wires.
@antsmith135
3 жыл бұрын
I've followed the video step by step. In his case the blower motor resistor was bad, but mine works. Where do i go from here? What's the next thing i can check. Any advice?
@MrStinkie123
2 жыл бұрын
Great information sir thank you.
@RichpinTv
2 жыл бұрын
You are welcome
@kipneal3653
3 ай бұрын
Thank you for the video sir
@KrnPanc
6 жыл бұрын
Wow thanks! This was exactly what I was looking for 😊
@guyincognito361
5 жыл бұрын
I just did this in my Durango a few months ago and now I have to do the one in my Grand Cherokee. The part isnt more than $30 ish dont get robbed at the parts counter.
@stormtrooperob
6 жыл бұрын
Thank you for posting this. I’ll be checking my soon.
@davonnelson2941
6 жыл бұрын
It worked for me! Thanks😊
@mr.dennisg.fleming723
10 жыл бұрын
great vid. thanks so much for this. it helped emencly
@MuddyBob650
5 жыл бұрын
I have a question... Would one be able to wire the colors together without a resistor? I'm the type of person, either you have the blower on, and on full. Or not on at all. Having these blowers running low burns these resistors. Just bad design. Thanks for this video!
@ericp3573
4 ай бұрын
generally if you have that kind of resistance the blower motor is working harder than it needs to be and is simply wearing out. When my blower locked up one day it took out the resistor pack with it
@jorireon12
4 жыл бұрын
very informative, i think i can do my vehicle now
@kingadasouth96
2 жыл бұрын
When you say "oh boy".. haha. Great video
@carpioamaya2977
7 ай бұрын
In 2024 ... I thank you sir, I have a Dodge Dakota 2001 ... Problem fixed
@RichpinTv
7 ай бұрын
I am glad to hear you got your problem fixed.
@scottys1423
8 жыл бұрын
Great video. i wish I had found it when I had to do this job the first time several years ago. In the past 6 years I've gone through 4 resistor blocks and 2 fused connectors. Factory connector was melted and and fused. The replacement lasted a couple years and did the same thing. I then used the extra set of wires that comes with the new connector and just connected those in the correct positions to a new resistor block. Used shrink wrap on each little connector so it would not touch the one next to it. The most recent resistor lasted about two months. As you know the fan runs only on high speed when the block goes out. The fan motor obviously works but I'm wondering if there is some way it could be drawing excess current and causing these resistor blocks to overheat. Thanks.
@scottys1423
8 жыл бұрын
+Scotty S. An update for anyone in the same boat. I removed the fan and sure enough it did not spin freely. The motor shaft bushing probably was overdue for some oil thus creating some drag and drawing excess amps. The trouble is the way the fan is designed you cant reach the shaft to oil the bushing. So head over to Amazon. I was able to get an aftermarket replacement fan for $40 TYC brand), a new resistor block and connector together for $12, and an extra resistor block to keep for a spare for $6 (both Dorman brand). Bolt it all in and splice the new wires in and it works great. So folks, always pull the fan and check that it turns easily when replacing the resistor block. And at these prices, it may be worth replacing all of it preemptively. Cheers!
@RichpinTv
8 жыл бұрын
+Scotty S Good tip.....yes spin the motor to check for drag.
@boonehoneycutt80
8 жыл бұрын
ive replaced my motor plus new plug and resistor. worked for 1 hr maybe And nothing now no fuse blowen either do you have any suggesting
@damonholly4233
4 жыл бұрын
Can the resistor go bad even if it doesn't look bad? (No corrosion) my blower would only work on high, over time got weaker, than finally stopped blowing for good. The resistor still looks good but not sure on how to test it
@D84D
7 жыл бұрын
Ok I broke some rules here. About 5 yrs ago my fan stopped working. Instead of doing it right I cut out the 2 connections/harness. I then taped the wires directly. This fixed the problem. Well 5 yrs later It's out again. Does this mean it's burned out? And if I replace it will it work?
@Collin_Creates
2 жыл бұрын
This was my problem thanks!
@angelerien7819
7 жыл бұрын
Thank you so much, great vid, light hearted and effective. appreciated!
@harrychitlin
8 жыл бұрын
excellent fixed it in 10 min no problem...
@Gunny426HemiPlymouth
17 күн бұрын
I now know why they sell a kit with a new plug and leads for these.... that also go bad. What a crappy design. Great video.
@chingli-xg4ns
10 ай бұрын
So it was the resistor not the Motor? I have a 09 Durango I wonder if it's in the same location?
@ferguson4914
10 жыл бұрын
Nice video...very helpful, thx
@ignacioalatorre4254
8 жыл бұрын
Nice video . you are awesome
@naseratashafrazeh3042
6 жыл бұрын
Cheers my friend,you just saved my,,,,,,,, thanks.
@Edgar.Meza.Photography
5 жыл бұрын
Great video
@vapingwithhoffman5775
5 жыл бұрын
what caused the resister to go bad to begin with? we need a update on the new restior u put in we want to know how long it took before it went bad too?
@MsPokemonsoulsilver
7 жыл бұрын
hey i have an 07 dakota and sometimes the vents work just fine and other times dont even turn on. is this what the problem could be?
@fredapeeples6619
6 жыл бұрын
Effing Dodge. I've spent 3 grand on repairs in the last 2 years, while still making payments on the effing Dodge...thanks for the video btw.
@shawnsmith7026
6 жыл бұрын
Yeah I’ve changed my resistor 6 times 3 connectors later and 3 blower motors later the last two pins in the resistor are burnt up is this because I have my heat always on high
@Roller76
5 жыл бұрын
No its because Dodge uses cheap parts in order for their partners to make extra money. Their window regulators are trash. I've replaced every window but all break. They use plastic parts inside to hold a tight cable and expect it to actually hold? If they used a metal part inside would avoid it. But Dodge knows this. Same as the switches on the driver door, they tend to go bad cuz they are cheap. Sad cuz I like the concept of the Dakota. I'd rather have a Dodge truck than a Ford or Chevy but Dodge has obvious areas to improve
@rubensilva9186
4 жыл бұрын
This is so sad, I grew up whit my dad using American cars and trucks and I was doing the same, I went through the tree big ones and now based in my son experience I'm thinking to switch for a Toyota truck, still I have a dodge Dakota very poor constructed and a 2014 ford Mustang whit transmission, suspension, breaks, fuel, cooling, integrity and sound problems at the point that I'm going to sale it and buy a Toyota 86 for my wife. it is incredible the lack of materials quality and the poor design. Toyota, finally I'm ready to give you a tray.
@tronmakaveli3069
2 жыл бұрын
Good video i should have the heat goin on easy street thank
@RichpinTv
2 жыл бұрын
Glad to hear that.
@tronmakaveli3069
2 жыл бұрын
@@RichpinTv it worked out my man snip and pulled right out thanx
@Lupgaroo666
6 жыл бұрын
Great info but I would add a warning about airbags yo disconnect and isolate from grounding the negative battery terminal and wait 2 minutes for airbag capacitors to discharge to avoid airbag accidental deployment as per the dodge ship manual. Thanks
@carlunkle
8 жыл бұрын
what type of batter should I use to test the fan? Does it really matter?
@antegas
10 жыл бұрын
Good! Job. Richpin06. Thank you very much
@Angela-cc2jr
5 жыл бұрын
My 2002 Dodge Durango, heater not blowing out front, but back is still blowing. Any suggestions what could be wrong?
@pbooker7513
8 жыл бұрын
Thanks for the video...
@eazyboy2
9 ай бұрын
Thank you
@RichpinTv
8 ай бұрын
You're welcome
@andremartel828
7 жыл бұрын
That fan is just as noisy as mine. I put a new one on and its just as loud. Also I am on the third connector and 6th resistor. The newest connector harnes has larger wires. The plastic between the positive and negative leads is really thin. If the wire heats up it melts. It is not corrosion. It is a meltdown.
@andremartel828
7 жыл бұрын
Just found out what might be going on with my truck. This time the motor was not working, The new harness and the resistors were working. What I found may be on on going issue that I never seen until today. Water. Water is getting into the motor from somewhere in the duct system. It was getting dark and we have storms moving in. Will have to find the water problem tomorrow if it doesnt rain. This water issue may also be shorting out the resistor pack.
@RichpinTv
7 жыл бұрын
The water might be the problem.
@sniperfire1295
6 жыл бұрын
Thank you vary nice
@ezurmnd
8 жыл бұрын
is this the same procedure in the durango? the rear ones work fine but not the front one
@kevintroxclair935
6 жыл бұрын
What causing the blower resister to keep blowing out and only work in the high position 3one I bought this year
@guyincognito361
5 жыл бұрын
try a different brand
@oscarquesada5534
10 жыл бұрын
Hi, Any idea, what is wrong, if the blower a/c wasn't working at all, I changed the resistor and it worked fine (tip: once i changethe whole resistor, the other time I just changed the fuse on it which is only some cents value) AND it worked fine but only setting the control to 4, both times the same, looks like an extra heat is warming the resistor too hot and it burns, any ideas to help fixing it to burn and only work in 4.
@RichpinTv
10 жыл бұрын
Are you saying your blower only works on the high setting.
@oscarquesada459
10 жыл бұрын
richpin06a Hi Rich, yes ti Works only on the high setting (4th position) of the switch, but if I keep it for a while, say some 40 minutes it burns out again ( the resistance fuse) ( :) I tried with two fuses the other day and it worked for a Little more time just for once, I know bad idea:{ ) thanks again.
@guyincognito361
5 жыл бұрын
@@oscarquesada459 get another different resistor
@KreSade01
6 жыл бұрын
Is there an easier way to test it? Do the auto stores have computers that can find that?
@OPRT5763
4 жыл бұрын
How can these keep going out? I've a 2002 durango and for 2yrs this is the 2nd or 3rd. The wires keep frying! Any ideas???
@scottys1423
4 жыл бұрын
I have the answer and learned it the hard way. I went through 3 of these resistors on my Dakota. The problem is the 5-pin connector is not rated for the amp load on the highest and 2nd highest fan speed settings. Heat and oxidation would build up to the point the connector would melt and fuse to the resistor. So even with a new resistor block and connector it will just happen again. I finally solved it by soldering the wires directly to the pins on a new resistor block. You have to carefully cut away part of the shroud to get good access to solder. Once done, you can even fill the whole cavity with silicone sealer or epoxy as a potting compound. Mine has been working fine for four years now. Also, you can get new resistor block, connector with wires, and even new fan/motor assembly for very little $ on Amazon. Don't pay dealership prices.
@joeeister4244
5 жыл бұрын
What is the white circle plug above the blower motor resister?
Пікірлер: 203