I bought my 720 brand new in 1985 and I still have it. Until now, I have never seen what the engine looks like outside of the truck. Now I have. This also gives me a good view of where and how all the components are installed. Thanks!
@aaronpena1570
4 жыл бұрын
Looking great. I love how Walter always comes in right on cue. Can't end the video without him.
@carlsimons1688
3 жыл бұрын
I did up one of these engines for my truck a couple of years back. Had 230000Kms on clock. Skimmed head, new NPR rings, gaskets, big end bearings, water pump & timing chain set. Factory timing chain was a single row chain & had stretched badly, but fitted a double row kit same as video. Has been running very well since. Great engines although not big on HP. Nice video.
@hevog
4 жыл бұрын
Looks like a rugged, straightforward engine. Can't wait to see the Bushmaster roll. Like your videos, always a pleasure.
@Jerod_Helt
4 жыл бұрын
hevog thanks buddy!
@paulshamblin6260
3 жыл бұрын
Minor critique. The color. Original is dark blue. I went light blue like the early Datsun motors. I use an early crank gear and distributor drive and a 510 distributor.
@briankelly5503
4 жыл бұрын
Can't wait to see this thing going
@kdubb1208
4 жыл бұрын
I love it brother!! Keep them coming.
@Antuan_RU
7 ай бұрын
Pro man..your the better that best
@josefprem4535
4 жыл бұрын
Very Cool
@thomasmark8611
3 жыл бұрын
Thanks it help me
@808livin.8
2 жыл бұрын
Wish i could do mines and make it look so easy
@КалыванКалыванов-э9к
29 күн бұрын
Привет.Подскажите какие зазоры выставляли на клапананах,впуск и выпуск?Прокладка под ГБЦ оригинал или аналог?
@samwhite1345
Жыл бұрын
What is the silver thing above the left motor mount right side if your sitting in the car
@adammcgee8844
Жыл бұрын
Dude I absolutely cannot separate my oil pump it's driving me crazy bolts are out and it still spins just fine just won't come apart idk what to do
@livemeyer
5 ай бұрын
Question: I see three holes in the cam timing gear. I recall when my engine was rebuilt in 2003 I saw three options to insert the cam into. Then I messed up and had to take the engine into a shop for a rebuild. When I got it back I had to advance the distributor all the way forward or it wouldn't run properly. Could that be cam timing that is off? It has a performance cam in it with a bigger grind over stock. I don't know the specs. But it would be nice to not have to run the distributor out all the way to the end of its travel.
@Jerod_Helt
5 ай бұрын
Maybe someone can chime in on this. It’s been a few years since I assembled this engine so I don’t recall.
@luismontanez21
2 жыл бұрын
What pistons and valves did you use ? Head bolts ?
@hawaiiaction.1976
3 жыл бұрын
Why does my distributor drip oil from where the bolts go.
@PhillipLarsen-j4f
Ай бұрын
Would be nice if something was explained to watcher
@HbAdams-o7d
23 күн бұрын
can you give some links for parts??? i cant seem to find much for mine
@Jerod_Helt
23 күн бұрын
Sorry I don’t have the part numbers. I did this years ago. I got most parts from AutoZone
@Ultra_Neito
Жыл бұрын
Can anyone confirm the ka24e studs are the same as the z24?!
@jamesgooden4926
3 жыл бұрын
I have the same engine when I was installing my seal and harmonic balancer keep breaking the Woodruff key and breaking a chunk out of the part with the Woodruff key and making it leak real bad do you have any options I can use
@timothyadonis4970
3 жыл бұрын
Does any know if i can fit a rev limit rotor arm on the dizzy to limit the rev to 5500 rpm or lower
How can i have the cylinder head bolt tourqes for z24
@Jerod_Helt
11 ай бұрын
I usually buy the shop manual… or just google it
@durantalegri6222
4 жыл бұрын
Hello, can you tell me about the thermostat, what Is the part number i am having trouble finding videos about replacing It, mine does not have, so i don't know nothing about It.
@paulshamblin6260
3 жыл бұрын
Autozone has them. They're cheap. I'm sure ebay is full of them. There's a summer and winter thermostat. I think I just left summer in and out a garbage bag over the grill.
@jacobnorth8642
2 жыл бұрын
Your torque pattern (and loosening pattern) is different from what my manual specs. Also from what i gather, some people recommend after torquing, loosen and retorque one at a time. Others say to heat cycle it and retorque. People also say to retorque this motor every "tune up".
@samwhite1345
Жыл бұрын
It's didn't really matter what order you did it in these engine because there was a bad design in the deck the factory actually said to loosen and retorq them because the head gaskets would blow otherwise
@mttmsn
4 жыл бұрын
Bet you kept track of that razor blade..
@Jerod_Helt
4 жыл бұрын
Matt Mason sure did😀
@jamesgooden4926
3 жыл бұрын
I have the same engine do I have to have a oil Slinger in my engine or not
@Jerod_Helt
3 жыл бұрын
Some people use them some don’t. I think it’s fine either way. I had one so I used it.
@757king3
3 жыл бұрын
What kind of engine stand is that
@Jerod_Helt
3 жыл бұрын
There’s a link in the description for the engine stand👍
@wilsoncastellanos2641
3 жыл бұрын
How can I get me a book to assemble the motor especially
@wilsoncastellanos2641
3 жыл бұрын
I got a Nissan 1985 and it's giving no problem yet but would like to keep it intact
@Jerod_Helt
3 жыл бұрын
You can get a shop manual for just about any car. I get mine on Amazon 👍
@romandelgado4909
3 жыл бұрын
Hi, do you know any performance heads for this engine Z24 2.4 ?
@Jerod_Helt
3 жыл бұрын
No sorry
@dennislane4140
3 жыл бұрын
Z24 is race motor from stock back in 1980s
@trevorquinnell8515
3 жыл бұрын
How much to rebuild my engine
@Jerod_Helt
3 жыл бұрын
Sorry I don’t work on other people’s cars. These are my personal projects
Пікірлер: 49