Quick to the point and no BS I’ve never seen a video where the noise the videos title describes is actually shown/played within the first 30 seconds - y’all kick ass
@shawnbest8386
2 жыл бұрын
Thank you for shutting up while recording the noise. Just watched another video where the motor mouth ran the whole time. Very irritating
@kylehawton7483
Жыл бұрын
This literally helped me straight away, was chasing my tail for the last month trying o find the noise, can’t believe wd40 fixed it so quickly
@RVLPHIEBOI
3 жыл бұрын
I have the same noise with my 06’ Mazda 3 hatchback. Will lubricant and hopefully won’t need to replace the clutch and components. Great video!
@MrDamburger
3 жыл бұрын
that's coz mazdas suck
@klb1956
2 жыл бұрын
Sounds just like my throw out bearing in my 92YJ! Thought it was the hydraulic lines from the throw out bearing rubbing, but you just confirmed that for me. Time to take it down!
@felicityblakeley8361
5 жыл бұрын
Nice Yota! I came here looking out of curiosity due to my 97 Nissan Sentra making noise potentially related to a bad TO or pilot bearing. I also have a Toyota 87 FJ60 so seeing your little Toyota pickup was a delight. Thanks!
@robertbuck7186
Ай бұрын
Most clutch kits dont come with the pilot bearing. 8nnmy casec I am wondering if this is making the noise. Because there is not the same rattle noise that happens when the clutch pedal is pressed in.. it sounds like more of a squealing noise with the engine running.. then when you push the clutch in it goes away.. also if you push the clutch in about 1/2 inch it goes away.. I was think either it was the pilot bearing or Loose fork on the throw out bearing? Dried out pilot bearing thats going? It all points to an ecoensive repair and while you're in there might as well replace the whole clutch.. and pilot bearing which does not come with the clutch and has to be ordered seperately.. so yeah..its either ignore it until it goes at a time and place where it will need a tow or fix it... so looks like were in the same boat.
@NathanCelica
4 жыл бұрын
thanks for the video. Looks like i'm paying a visit to the guy that rebuilt my engine and replaced the clutch (it's only 1200km's old and already making these noises!! i'm pissed!)
@christiandefreese3020
3 жыл бұрын
Same here had a new clutch replaced drove it back to the shop and parked it. Went to take it to get the brakes touched up and boom 3 minutes after starting her up she starts making a squealing noise that sounds identical to a bad pulley, but when you engage the clutch the sound completely stops. So after engaging and disengaging the clutch to see if the noise would stop I tried one more time and boom clutch pedal just slammed to the floor gotta love life
@crazy8boy145
3 жыл бұрын
@@christiandefreese3020 What do you mean just slammed to the floor? Like youre supposed to shift with it all the way in is what your saying?
@RipperYouTubeOfficial
2 жыл бұрын
@@crazy8boy145 He must have left his phone in the car when he took it back for repair
@steak1659
Жыл бұрын
thank you so much my truck just started making a clicking noise and i thought it was the throwout but now i know it is
@xalbertoherrerax
2 жыл бұрын
I'm guessing all different models of vehicles may make different pitch sounds depending how bad they are worn or un lubed . I'm getting a sound.. when I engage clutch it quiets down drastically. I'm aware I may have a squeaky belt pulley or something else but do notice my clutch actually sets me in motion when I press all the way down and then release from down there. ... what am I looking at in costs in so. California 2004 ram 1500 v6 3.7 need a clutch quote
@MotorHeadMadnessOfficial
2 жыл бұрын
I couldn't tell you the cost. Probably around 1800. But yes every car is different.
@brandonion5647
3 жыл бұрын
Isn't noise that gos away with the clutch pedal pressed in the input shaft bearing not the TOB?
@retrokirito5428
2 жыл бұрын
Noise when clutch is in = TOB Noise when clutch is out = PB
@theboebieman4318
Жыл бұрын
PB?
@theboebieman4318
Жыл бұрын
Pilot bearing?
@retrokirito5428
Жыл бұрын
@@theboebieman4318 yes
@kotymccallister5150
3 жыл бұрын
That knocking was the input shaft bearing
@rishinjose8858
5 жыл бұрын
My car has that squeeky sound while applying clutch and when i accelerate in first gear and shift it to second gear its not accelerating smoothly as if clutch is not disengaging..jammed feeling..what is it,?
@moparmadnes1318
5 жыл бұрын
Throw out bearing..and by the sounds check your clutch and flywheel they might be gone aswell when flywheel/flexplate wears away to much the clutch will bond to the flywheel or it will slip..good luck
@sirius1552
5 жыл бұрын
I have a weird sound. It almost sounds like a flutter when the clutch is released in first gear at higher rpms. Its there in 2nd gear but harder to hear. Its hard to explain what it sounds like but its like something is knocking or tapping and it get quieter after every knock. Almost like a flutter it doesnt get faster after every tap. I cant find anything on the internet about it
@noliberalismeveragain
7 ай бұрын
flutter...boat motor noise...... I've I've got that noise And it's very rarely discussed online...... This is the 4th clutch kit..... The 1st 3 kids were making a tapping sound Just idling I don't know if they made a sound between each gear.... But the fluttering noise right now is with a Luk clutch..... It's been going on for 3 years......
How can we be 100% sure it is the throw out bearing? I have a dodge neon srt4 and mechanics told me that noise is related to the input shaft bearing not the tob as i thought initially, how to be sure?
@faithfulnona6495
4 жыл бұрын
I have the same noise. Before trying it I had a couple of questions though. Did the other bearing brake due due the grease you put in? E.g. the grease flying around an bringing particles where they should not? Was the clutch greasy when you took it out? I would apreciate clearing that up.
@tnamen1307
5 жыл бұрын
My car i20 has the same and exact sound at 0.12. what exactly is that noise? How do you fix it?
@OG_PC-Wizzard240hz
Жыл бұрын
no BS stright to the point love it thanku! help me on my mustang. probably need lube crossing my fingers since i just did a clutch kit 2 months ago..
@gliderman1176
Жыл бұрын
Hey y'all that's not a bad throwout bearing that rattling at the end of the video is the pressure plate fingers so you need a different brand or you need to tighten it in a star pattern
@MotorHeadMadnessOfficial
Жыл бұрын
Great guess but I pulled that truck apart myself and it was definitely not the clutch fingers
@darrosoarragant2806
3 жыл бұрын
For the second example what sound is that ?
@akuma12356
Жыл бұрын
why is the noise more when clutch is out? That's when the throw out bearing is not spinning? or its rattling side to side? so clutch it presses the bearing on the springs so doesn't get chance to rattle?
@gasisthepastendoil
10 ай бұрын
When your clutch is out and in neutral We are spinning the entire transmission and there's going to be noise absolutely every single year every ball bearing
@gghhj6360
2 жыл бұрын
I had that rap and tapping on the very first clutch kit that is shop installed on a Nissan truck
@evancauler789
6 жыл бұрын
You said you had to pull the trans again? Did it end up being an input shaft bearing in the trans or was it actually the throwout bearing ?
@MotorHeadMadnessOfficial
6 жыл бұрын
only pulled it once,. replaced everything while it was out and its been a year now 0 problems.
@torrellsavy1097
2 жыл бұрын
Great video
@glitchthecat5011
2 жыл бұрын
Possibly you accidently oversprayed the clutch/components,did you Evan check the throwout bearing?
@MotorHeadMadnessOfficial
2 жыл бұрын
I replaced the whole clutch assembly and bearings later on. The noise was the throwout bearing if im not mistaken. Its been quite a few years
@MotorHeadMadnessOfficial
2 жыл бұрын
It was all pretty bad truck had the original clutch from 1982 in it still
@MotorHeadMadnessOfficial
5 жыл бұрын
If you liked the video subscribe for more automotive tips, tricks, diagnostics and etc.
@codiekennedy8046
6 жыл бұрын
Got a nissan d21. No clutch pressure at all sits on floor. Got a new master snd slave and bled and nothing. Clutch fork is all the way to rear (back of truck) at rest resting on pivot joint. Will noy move by hand. Based on pics I've seen it appears my fork is farther back than others. About 2 inches of slave piston out and based on pics should be about a half inch any ideas? It woulf seem to me no matter what goes on beyond slave I should still have pressute at pedal
@johnlessary8504
6 жыл бұрын
i have an 89 d21 with the z24. i also changed my master and slave units. had no pressure.. turned out that on the bracket the connects to your clutch pedal had to be adjusted.. after i turned it like 5 or six times i had full clutch pressure... hope this helps ya.
@johnlessary8504
6 жыл бұрын
bro. are you on the Nissan d21 global page on facebook? if not you should join.. its pretty cool.
@Adam-FR
5 жыл бұрын
Is that a front wheel drive? And where did you spray for that joint? Looked like you were spraying that fork more on the clutch side... I'm still having a squeak, but I was being extremely careful with the spray I have so I don't think I hit the spot well or got the wrong side.
@MotorHeadMadnessOfficial
5 жыл бұрын
This is a 1982 toyota hilux rwd. I sprayed the clutch fork where it meets the pivot. I used white lithium grease. I also ended up finding out that my throwout bearing had started to fail causing a rattle that the squeak was hiding. I pulled the trans and di a new flywheel, clutch and both pilot bearing and throwout bearing. I also replace my master and slave cylinder while it was apart.
@Adam-FR
5 жыл бұрын
@@MotorHeadMadnessOfficial nah yea I get the throwout bearing is going bad, but mine is just doing that squeak and I'm trying to get rid of that.
@bertoloche
6 жыл бұрын
I have the same noise when pressing and releasing the pedal... did you find out the exact problem?
@MotorHeadMadnessOfficial
6 жыл бұрын
bertoloche throwout bearing
@tnamen1307
5 жыл бұрын
@@MotorHeadMadnessOfficial My car i20 has the same and exact sound at 0.12. what exactly is that noise? How do you fix it?
@cristianhernandez7537
2 жыл бұрын
Did you ever have problems shifting in gear?
@MotorHeadMadnessOfficial
2 жыл бұрын
Thats probably unrelated to the bearings. You have clutch issues. Low transmission fluid or synchros are going bad.
@travispetrovich7642
Жыл бұрын
Nice video and cool dogs!
@adamabelas3545
5 жыл бұрын
Are all gearbox able to remove the sleeve that the thrust bearing goes on and replace it. My gearbox thrust bearing was that bad that it wore out the sleeve that it slides on
@MotorHeadMadnessOfficial
5 жыл бұрын
I dont see why not
@patrickscott1604
4 жыл бұрын
What should i do i just replaced the clutch kit and the throw out bearing went out after 100 miles?
@pauld8747
4 жыл бұрын
Hey I have an 88 toyota pickup and I only get a rattling sound when accelerating into first gear. I have to depress the clutch more than before now or rev it higher to get it to go away. Any ideas?
@MotorHeadMadnessOfficial
4 жыл бұрын
Hard to say but it could be the heatshield rattling
@bwatt1383
6 жыл бұрын
I have a yaris that sounds like this but I got a full clutch job 5 months ago.. I'm just waiting for a change In shift feel or something, I have a aaa membership in case a part fails suddenly. Would you suspect that my new flywheel was unevenly torqued? My clutch pedal has a vibration feel at the top 10% of the stroke. My car was perfect before the clutch job I regret it !
@MotorHeadMadnessOfficial
6 жыл бұрын
Id assume it was done wrong
@gghhj6360
2 жыл бұрын
Did you ever fix it with a different brand of clutch kit?
@evancauler789
6 жыл бұрын
Sorry , when you say replaced everything, do you mean inside the transmission as well or just clutch components ?
@MotorHeadMadnessOfficial
6 жыл бұрын
east.coast Ev I mean the Clutch, fork, both bearings, the flywheel and transmission fluid. New master and slave cylinder and new hydraulic brake fluid too.
@justme3350
5 жыл бұрын
So what would be the problem for shaking like at 0:17?
@MotorHeadMadnessOfficial
5 жыл бұрын
That was actually my truck warming up. Its carb
@tnamen1307
5 жыл бұрын
@@MotorHeadMadnessOfficial My car i20 has the same and exact sound at 0.12. what exactly is that noise? How do you fix it?
@warrenpike8110
3 жыл бұрын
Thank you!!!
@kevinish5567
5 жыл бұрын
Do you hear any "krrrg krrrg krrrg" noise occasionally coming from your transmission and if you do ,is it due to the bad release bearing?
@MotorHeadMadnessOfficial
5 жыл бұрын
Replace it all they come as kits anyway
@tnamen1307
5 жыл бұрын
@@MotorHeadMadnessOfficial My car i20 has the same and exact sound at 0.12. what exactly is that noise? How do you fix it?
@m.d.498
2 жыл бұрын
Did that end up being a throwout bearing or was it the inpit shaft bearing on tranny? I woul have thought throw out would make noise with pedal depressed.
@m.d.498
2 жыл бұрын
Input shaft bearing**
@MotorHeadMadnessOfficial
2 жыл бұрын
My vehicle it was the throwout bearing. The input shaft bearing whines. It is inside of the transmission
@MotorHeadMadnessOfficial
2 жыл бұрын
There's another video about input shaft noise on my channel
@m.d.498
2 жыл бұрын
@@MotorHeadMadnessOfficial ill check it out. Awesome
@ryandudgeon782
Жыл бұрын
Had same problem sprayed it took nose away but did something to Frist gear if I could go bk I'd leave it well alone my clutch was new enough aswell this shit happens in cars it's normal not ment to last for ever just drive it squeak is no hard
@boostedsc4040
3 жыл бұрын
Damn it I think my sc has a bad throw out bearing it makes the same noise
@krupt79
3 жыл бұрын
I have the exact same sound from my rebuilt auto, any ideas out there on a quick fix??
@gliderman1176
Жыл бұрын
Used a ziptie n put in grease....
@flipinfin
5 жыл бұрын
What if i have pressure in my clutch when the cars off but when its running i have no pressure?
@FunkieGuyz
4 жыл бұрын
could be the clutch pedal itself need some adjustment for the clutch engagement point
@dakotaedens6599
3 жыл бұрын
Mine only makes a noise when accelerating. Sounds almost identical to yours
@gliderarts3573
2 жыл бұрын
What about clutch fork vibration my car has destroyed 3 throw out bearings in 3 months
@MotorHeadMadnessOfficial
2 жыл бұрын
Could be the input shaft bearing
@gliderarts3573
2 жыл бұрын
@@MotorHeadMadnessOfficial ... Install the different brand with a brand new fly we'll and almost all of the vibration is gone however now I hear a draging n sound within the transmission itself and the entire transmission was rebuilt recently..... What am I transmission was tore down the input check bearing had a japanese marking on it so now wondering if the japanese bearings are no longer available it's making all kinds of dragging noises not very loud but Oh well
@MotorHeadMadnessOfficial
2 жыл бұрын
I have a video on here about bad input shaft bearing sound. Its on a honda but it may sound similar
@gliderarts3573
2 жыл бұрын
@@MotorHeadMadnessOfficial I'm getting a sound but it's only in second gear With the clutch in are out I think it's the counter shaft Which is always in motion because of the drive shaft it's a real drive truck....
@jwaxent
4 жыл бұрын
when my clutch is out it makes a chirping squeaky sound. it’s progressively gotten worse. ive assumed it was the same thing. do you have a 2nd video showing the actual fix of the clutch?
@NotShuba
3 жыл бұрын
He showed a new clutch kit with a new throw out bearing since that is the issue. You could just replace the throw out bearing or do what i assume he did and put on that new clutch kit with a throw out bearing
@elhatch2503
4 жыл бұрын
Only my clutch does that noise? How do i fix it
@elhatch2503
4 жыл бұрын
When i put the clutch in it does the squeaky noise
@cheeto408
3 жыл бұрын
Same any news ?
@teadoughh8915
3 жыл бұрын
Is white lithium grease the best recommendation ? I have a 97 mustang v6 and my clutch fork is squeaking against my pivot ball thingy whenever my clutch pedal is released and wanted to know if that grease is best for lubrication and fixing that annoying chirping sound.
@basilco2941
3 жыл бұрын
I have the same problem, I plenty sprayed white lithium 3 days ago and the noise is back on. I wonder if there is any better grease…
@vilfrientsen506
Жыл бұрын
thanks! just like mine
@gliderarts3573
2 жыл бұрын
At the end of the video you can hear the throw out bearing wobbling from the fingers of the pressure plate who knows a lot of people have got this problem And the Chinese parts don't help
@MotorHeadMadnessOfficial
2 жыл бұрын
Exactly! Cheap bearings fail often
@luisbarrueta658
4 жыл бұрын
I fuckin love you guys....
@frankieeh2
3 жыл бұрын
That clutch out is not a throwout bearing, they make noise when pressing the clutch in
@MotorHeadMadnessOfficial
3 жыл бұрын
Sure was the throw out bearing. I replaced it and I still daily this truck. The noise is gone
@frankieeh2
3 жыл бұрын
Throwout bearing does nothing if the clutch is not being pressed in, unless u explained it the other way around.
@Ajhowardz32
4 жыл бұрын
Mine gets louder when I rev it
@MotorHeadMadnessOfficial
4 жыл бұрын
Thats rod knock or timing chains
@MotorHeadMadnessOfficial
4 жыл бұрын
Hard to say but if it changes with rpm thats a bad thing
@Ajhowardz32
4 жыл бұрын
MotorHeadMadness when I push the clutch pedal in it goes away
@kirleyq1394
3 жыл бұрын
@@Ajhowardz32 Throwout bearing
@irimach.384
4 жыл бұрын
I fix mine flush and refill my gear oil.
@noliberalismeveragain
7 ай бұрын
..... They can make that noise when it's brand new.........
@MotorHeadMadnessOfficial
7 ай бұрын
Not if you properly clean and lubricate them I’ve had many 20r and 22r motors
@MotorHeadMadnessOfficial
7 ай бұрын
The noise is from the slave squeaking on the clutch fork
@crazy8boy145
3 жыл бұрын
Just kinda sucks cause my clutch is brand new, looks like this shitty garage is gunna have to take my car back and do it right.
@MotorHeadMadnessOfficial
3 жыл бұрын
Sounds like they didn't replace bearings while they were there
@crazy8boy145
3 жыл бұрын
@@MotorHeadMadnessOfficial It actually ended up being a metal heat sheild that was loose😂, every time I would clutch in it was rubbing against the clutch slave cylinder and making a noise, removed that shit
@crazy8boy145
3 жыл бұрын
@@MotorHeadMadnessOfficial Thank u for the advice tho appreciated
@gasisthepastendoil
10 ай бұрын
fvhnn.... I am a club expert if anyone has a question just ask me been through it all
Пікірлер: 119