Great video. It’s also a good idea to put some blocks of wood under the rim/tire so the weight of wheel assembly is supported by the rim/tire and the brake disc isn’t resting on the concrete or other work surface.
@LowCountryHarleyDavidson
10 ай бұрын
Great addition to this tech Tip👍….Doc
@rickyhawkins7407
10 ай бұрын
2018 with 115,000 miles. Awesome for that owner. Wish I could ride mine that much.
@oldamerican8070
10 ай бұрын
That's a good practice for any multiple anchor assembly. Thanks Doc.
@zoof1
10 ай бұрын
I put the spacers in first without the bolt and made sure they were all in the disk correctly then the bolt and spring for each one. Much easier.
@schachat01
10 ай бұрын
Thanks Doc for another great tech tip explained in very thorough and concise manner👏
@stephendrake8145
10 ай бұрын
i prefer the full floating discs with the brake disc separated from the carrier which is bolted to the wheel. This allows the disc to float more freely and isolates the heat & expansion of the brake disc from the wheel assembly. Also the standard wheels have a bolt pattern that allows fewer choices of full floating discs. May you have a wonderful Thanksgiving now Doc...
@LowCountryHarleyDavidson
10 ай бұрын
Thankful for your added input….Doc
@medcook57
10 ай бұрын
As always, great information on something you don't do very often. I had no idea about all of the do's and don'ts.
@bradduffield9603
10 ай бұрын
Thanks Doc for the expert advice.
@kevin6070
10 ай бұрын
Awesome 👍🏻 great information on making sure even if someone doesn’t for you to keep a close eye on them , job well done ✅ Doc
5 ай бұрын
Hey Doc Recommend cleaing internal threads if Loctite was used. Using 22 caliber bore mop and lighter fluid, then bore brush, hit with compressed air (covering with rag)
@LowCountryHarleyDavidson
5 ай бұрын
Thanks for posting your tech tip…Doc
@CabinGuy
10 ай бұрын
Thanks for all the great tips Doc, love your channel !!
@Pwpapa.7
7 ай бұрын
Thank you for this video and information getting ready to do my bike this weekend 😎🥃 in Michigan
@LowCountryHarleyDavidson
7 ай бұрын
Have fun!….Doc
@georgeparker7108
10 ай бұрын
Thanks for sharing Doc, I've learnt something new.
@CATmanATL22
10 ай бұрын
Good tip Doc ,just in time . In the spring when I do my brakes I have to do my rotors on my Roadking ……..
@DC-sh8mr
10 ай бұрын
I put spacers and springs in rotor first then I put screws in. I start them by hand. Blue locktight.
@TrustyZ900
6 ай бұрын
Parts made in Italy, how delightful!!!!
@ernestrhoades5147
5 ай бұрын
Those things you are calling springs are actually Bellville washers and they come in differant thicknes to get a preload on a assembly .
@travisgray3331
10 ай бұрын
Thanks Doc. Happy Holidays to you and your crew
@LowCountryHarleyDavidson
10 ай бұрын
Same to you…..Doc
@randybard224
10 ай бұрын
Don’t forget to chase the bolt holes Also make sure to check the wheel bearings also
@jrhandford8356
10 ай бұрын
Thanks Doc. Just did this on my 2015 Road King and got rid of a clunking noise from front brakes. Now if you could do a video on the noisy front disk on my 2012 Dyna....lol
@LowCountryHarleyDavidson
10 ай бұрын
Lol….Doc
@okiemale1589
10 ай бұрын
😎👍 Big thumbs up for the channel... Good job Doc...
@LowCountryHarleyDavidson
10 ай бұрын
Thank you…..Doc
@philp1072
8 ай бұрын
Thanks Doc really appreciate the great video
@LowCountryHarleyDavidson
8 ай бұрын
Thanks for watching….Doc
@billcorbin6174
10 ай бұрын
Thanks Doc!
@LowCountryHarleyDavidson
10 ай бұрын
Thanks for tuning in on your day off….Doc
@foreigncorrespondent5140
10 ай бұрын
Good point Doc. Spacers and all screws, should go back into the same places on the whole bike.
@chrislanagan1128
10 ай бұрын
Needed to see this I'll be doing this in few weeks 🤟 thank YOU 💯 % for all your tips thru Year's 🤟
@LowCountryHarleyDavidson
10 ай бұрын
I appreciate your support….Doc
@bobmurphy3723
10 ай бұрын
No lock tight? Thing’s I didn’t know thanks Doc
@darrell3368
10 ай бұрын
Happy Thanksgiving to you all and Hods blessings for you and all your family
@LowCountryHarleyDavidson
10 ай бұрын
Blessings to you….Doc
@kzscorner5813
10 ай бұрын
My new to me 08 Road King classic (less than 400 mi on her this season) pulses while braking. Going to do brake fluid and pad inspection and now while at it, will be replacing the rotors hardware and probably check run out too. Subscribed to your channel before owning my first Harley. Thanks Doc.
@LowCountryHarleyDavidson
10 ай бұрын
Wow! Thank you….Doc
@ihateemael
10 ай бұрын
sometimes that's caused by real hard braking to a dead stop. The real hot pad material micro-welds to the disc at the point where the disc stops . . You could try new-pad-breakin again. It can't hurt.
@kzscorner5813
10 ай бұрын
@@ihateemael Not totally understanding the concept of floating disc just yet. Are you talking about when the disc becomes glazed? As a preventative, I honed the rotors on my Goldwing when I did the front brakes. The rotors on the Road King are effective as is, but annoying. Would like them to feel as smooth as the Wing. Neither bike has ABS, wish they did though. I think a dial indicator is going to tell me some history of the King.
@ihateemael
10 ай бұрын
@@kzscorner5813 I don't wish to talk over Doc here . . During pad bed in brake pad material actually coats the surface of the rotor and bonds to it. Rotors will look a little dull in appearance. The process requires warming up your brakes, then 5 or 6 progressively harder stops . . down to a slow speed, without coming to a full stop. Then not braking again till the rotor cools down. I went for a ride up the local mountain and did front brakes first then the rear another day. . each time using the cold disc when I needed to come to a stop. If you get my meaning. Doing this actually gave my m8 Fatboy brakes with at least a little bite.
@kzscorner5813
10 ай бұрын
@@ihateemael Appreciate your input, certainly won’t hurt resettling the pads vs buying new rotors. Haven’t mic them, but they don’t look bad.
@chuckchapiewsky7535
3 ай бұрын
Put the spring on the spacer,then put spacer and spring into rotor followed by bolt.
@DIYmotorcycle
10 ай бұрын
One thing that's important you always want to use Loctite on these bolts I use red myself because they're going to be on there for a long time anyways. If you noticed the factory Bolts from Harley already came coated with a Loctite compound.
@TheRoadGlideRider
10 ай бұрын
Really enjoy your videos 👍🏽💯🏍💨🏍💨
@LowCountryHarleyDavidson
10 ай бұрын
Thanks 👍….Doc
@MichaelDrentlaw
9 ай бұрын
Answer to a few questions, yes 115K, yes original discs, not the original wheel-was replaced at approx 75K due to pot hole bending rim and all other components checked at that time. Hope she make it over 250K. Currently no engine issues,only regular maintenance performed by both LCHD and Summerville HD. Thanks guys and thanks DOC.
@LowCountryHarleyDavidson
9 ай бұрын
Thank you for sharing and shout out👍….Doc
@freddetro7020
10 ай бұрын
Happy Thanksgiving, Doc.
@LowCountryHarleyDavidson
10 ай бұрын
Same to you!….Doc
@KyWindage
10 ай бұрын
Good to know to change hardware.
@exupakias
10 ай бұрын
Thank you Doc(tor)
@deanbalouris330
4 ай бұрын
Good time to replace the wheel bearings, too.
@LowCountryHarleyDavidson
4 ай бұрын
Only if needed. You do know there is an interference fitment. Only so many times you can take a bearing in and out….Doc
@stanjohnson8040
10 ай бұрын
I like your torque wrench.
@LowCountryHarleyDavidson
10 ай бұрын
Me Too……Doc
@stanjohnson8040
10 ай бұрын
@@LowCountryHarleyDavidson I have a Snap-On that beeps and vibrates but it doesn’t have the indicator lights like yours. Those lights are a nice touch.
@richardhartley7094
6 ай бұрын
👍👍
@aw738
10 ай бұрын
It looks like the spacers are making a two piece shoulder bolt. One that allows the rotor to have some movement. Do the spacers fit the holes in the rotor? If so why can't you put the spacer and spring in the rotor hole first and then start all the bolts. Putting the bolts in far enough so the spacers don't come out of the holes. Then tighten them.
@LowCountryHarleyDavidson
10 ай бұрын
That could work I guess…..Doc
@ryanholmes2248
Ай бұрын
I picked up a used 2020 FLTRK and have a question on these floating disc brakes-do they/are they supposed to make a clunk noise when you change rotational force of braking? Example, rolling backwards into slight sloped garage and stop with front wheel. Then when I pull out of garage and stop at driveway I hear and feel a clunk. I verified this by pulling back and braking and pushing forward and braking stationary and feel it clunk again.
@LowCountryHarleyDavidson
Ай бұрын
In my opinion without measuring, sounds like the isolator buttons are too worn…..Doc
@roncoburn7771
10 ай бұрын
All Brembo parts Happy turkey day Doc
@LowCountryHarleyDavidson
10 ай бұрын
Thank you. Same to you….Doc
@Bass.Player
10 ай бұрын
The springs keep the rotor from rattling...
@normswaebe6003
Күн бұрын
At 5:55 you say "16-24 inch foot pounds" the service manual for my 22sg states "16-24 foot pounds" which is right?
@LowCountryHarleyDavidson
17 сағат бұрын
I am human. Use the official Harley-Davidson Service Manual always….Doc
@normswaebe6003
15 сағат бұрын
I figured it was a slip of the tongue but just wanted to clarify, thanks for all you do!
@DNiddy
10 ай бұрын
Good tip on those washers. However, as Dad always said, sometime OEM is not the best. The owner of that bike should have gone with Galfer rotors.
@LowCountryHarleyDavidson
10 ай бұрын
Those are a choice if with in the budget along with Pads that match these special disc…..Doc
@shannonmoore1990
3 ай бұрын
Does this apply to the back rotor as well?
@LowCountryHarleyDavidson
3 ай бұрын
Yes but torque on rear disc hardware is greater….Doc
@bigj200016
10 ай бұрын
Doc, I hear the terms floating and fixed. What exactly does that mean and what’s the difference between the two?
@LowCountryHarleyDavidson
10 ай бұрын
Well as you watched the video you saw the three pieces. Bolt, spacer and Spring. The disc is not bolted directly to the hub solidly. It floats just a small amount on the spring. There are many advantages to floating disc.
@robertturriff9836
10 ай бұрын
Just a quick question about the sevice manual, do I need to get one from the harley davidson shop or will one like Clymer manual work?
@LowCountryHarleyDavidson
10 ай бұрын
The Harley-Davidson Factory Service, Parts and Electrical Diagnostic Manuals are the best…..Doc
@greenmarine5
4 ай бұрын
This actually is still a solid rotor not a floating rotor, Harley changed the design, and since the bolts don't actually bolt directly to the rotor, but to the spacers, Harley calls them a floating rotor, This will protect your rotor from transferring braking heat to the wheel hub or rim but does nothing to protect the Rotor from warping and is also the reason why true floating rotors are a two piece design. A true floating rotor consists of two parts, the part that bolts to the wheel hub, then the rotor bolts to that. Track or MotoGP Bikes use the true floating rotor, because they do not warp under extreme heat. Harley's rendition of a floating rotor doesn't really work,.. it does but it doesn't. If you had a seized caliper on Harley's floating rotor the rotor would still warp but all the heat would not transfer to the wheel destroying your barring's On a true floating rotor it would not warp and not transfer the heat to the wheel, hub or Rim what ever you prefer it's called.. This is why MotoGP switched to two piece floating rotors in 1992.
@LowCountryHarleyDavidson
4 ай бұрын
Thank you for the tutorial….Doc
@P46345
10 ай бұрын
If you stand the wheel up gravity won't work against you with the hardware.
@Tryke_Ryder
10 ай бұрын
No lock tire used? (On standard non-floating rotors, would lock title be used?)
@LowCountryHarleyDavidson
10 ай бұрын
Bolts come with Factory Loctite….Doc
@ardyrides834
10 ай бұрын
Why are you working on the floor?
@LowCountryHarleyDavidson
10 ай бұрын
Because I still can…..Doc
@rebel_ltz
10 ай бұрын
No thread chasing or using loctite?
@LowCountryHarleyDavidson
10 ай бұрын
The thread chasing would have been a great addition. Bolts come with Factory loctite…..Doc
@michaelsnyder2218
10 ай бұрын
2019 road glide standard coming on 50,000 miles. What’s your recommendation for checking these at this point?
@LowCountryHarleyDavidson
10 ай бұрын
That is a major milestone. It is always good to check. Those 50K could have all been in the mountains with a lot of braking😆…..Doc
@michaelsnyder2218
10 ай бұрын
@@LowCountryHarleyDavidson no mountains but still Lots of use. ThankYou Doc & have a great Thanksgiving 🙏🙏🙏😎🏍️🇺🇸
@michaelblandina7405
10 ай бұрын
Why no anti-seize Doc??
@leea.6101
10 ай бұрын
Doc, no blue Loctite?
@LowCountryHarleyDavidson
10 ай бұрын
Locktite already on the bolts from the company….Doc
@mikehammer2408
10 ай бұрын
Hopefully those bearings should have been changed for good measure
@LowCountryHarleyDavidson
10 ай бұрын
They were checked👍….Doc
@johnmitchell9705
10 ай бұрын
Not blue Loctite?
@LowCountryHarleyDavidson
10 ай бұрын
New bolts come with factory loctite….Doc
@mikefisher4557
5 ай бұрын
Taught not to use air or power tools to assemble parts that have tight tolerances. Work on a bench. .... will save your back.
@edharbas4828
4 ай бұрын
You guys are great, looking after one another like that, the idea of a bench to save one's back, banter on the benefits of manual tools almost like a buddhist master testing a novitiate with a koan. 'What is a torque wrench?' To which the novice could reply, '3lbs of steel'. This abstract 'zen' reply would save the novice the master's wrath and 30 blows from his whisk. Anyway had a 91 Dyna with a 2 point rubber system. Would vibration at lower rev-range mean either rubber mount problems? The bike had about 68000 miles without a change of rubbers. The vibration seemed there always, the bike was in an accident before I bought it with 6000miles. Enjoying the learning, thanks for the answers.
@sgtwrench69
10 ай бұрын
115,000 miles🤔🤔🤔
@LowCountryHarleyDavidson
10 ай бұрын
What’s to think about?…..Doc
@thomaskavney4656
5 ай бұрын
I don't like the floating brake rotors they clunk when you brake and i brought it to the dealer and was told that its normal
@LowCountryHarleyDavidson
5 ай бұрын
That would be a great Question for Harley-Davidson Customer Service. Be sure to mention the dealer name and location…..Doc
@waterkoppie
10 ай бұрын
Maybe do not use power tools ? For a better feel. Or maybe this was just for a quick video.
@LowCountryHarleyDavidson
10 ай бұрын
A tech must know the power tool. This was a 1/4 drive with adjustable power settings….Doc
@brian833
10 ай бұрын
This should really not be classified as a floating disc. IMO
@LowCountryHarleyDavidson
10 ай бұрын
Your definition of floating disc?…..Doc
@brian833
10 ай бұрын
Hi Doc I have a 2019 Sport Glide and really love her! I saw a well respected Vid on cleaning a floating disc due to brake dust and grime. When I tried to get the rings of my disc to turn they would not! So to answer- A disc with some freewheeling. Hope you had a great Holiday!@@LowCountryHarleyDavidson
@supakamario
10 ай бұрын
harley know they will reinvent a properly working wheel just to be proprietary. that's why ibdont own 1
@LowCountryHarleyDavidson
10 ай бұрын
Well thanks for visiting……Doc
@supakamario
10 ай бұрын
@LowCountryHarleyDavidson I don't visit, I live here just cause harley makes me sick doesn't mean u do..... I watch all ur stuff. I actually like harley just love victory
@whocares0692
10 ай бұрын
Another great video Doc. But may I make a suggestion on the spacer ? Instead of using your fingers, because some of us has "sausage fingers", how about using an auto door panel remover or trim puller instead? If the slot isn't wide enough foe the bolt, int can be drilled to a larger size. Just my opinion after watching your video because I'll probably be changing mine nets spring / summer.
@LowCountryHarleyDavidson
10 ай бұрын
Being sarcastic, haven’t needed a door panel or trim tool for a Harley-Davidson but I will keep this in mind👍…..Doc
@whocares0692
10 ай бұрын
@@LowCountryHarleyDavidson, DOH .... I stand corrected ..... for a car. LOL
Пікірлер: 117