This is a quick video of a TIPM from my 2002 Dodge Ram which had the low beam issues everyone has had. Just a quick video of the issue, cause, and repair.
If you have only the rear passenger turn signal operating and a problem with your headlights and emergency flashers Curt's fix will absolutely repair your problem! An important step that is not in this video would be how to remove the fuse box and how to separate the fuse panel from the box to gain access to the printed circuit board. There is a KZitem video that does show how to do this. If you look closely you will see three recessed buttons, either use a screw driver and break them off or carefully drill them out. Then pry around the sides to separate. Curt thanks so much, great to have my truck on the road again!
@Snagglepussify
5 жыл бұрын
Some advice for those who decide to use a salvaged TIPM rather than repair. First of all, this is NOT a TIPM, it's an IPM. These earlier Dodges (up to '06 I believe) used an IPM (basically a fuse box with circuitry) which had a FCM (front control module) bolted on to it. A TIPM has the two parts combined as one unit. The FCM contains an eeprom which is married to the VIN# of the vehicle. If you swap out the IPM make sure you use your existing FCM (it's the aluminum box on the side of the IPM). If you use a salvaged IPM including FCM, you'll have all kinds of odd 'Lamp Errors' which will entail having your vehicle reprogrammed. To sum up: The IPM is 'plug & play' as long as you use the original FCM.
@johnterpack3940
5 жыл бұрын
It's hard finding information about the IPM on my '04 Ram because it's impossible to search for "IPM" without getting videos about "TIPM". Is there any way to determine if my FCM is the factory one? I have tons of questions about the various CMs on my Dodge and cannot find reliable answers anywhere. My main question is whether or not I even have a Body Control Module since my truck has no power accessories. I bought the truck specifically because it has manual transmission, manual windows, manual door locks, manual transfer case... it's as "dumb" a car as you can get these days. I really want to ditch the IPM and FCM in favor of running the lights through an ordinary fuse box but I don't know if I can do that without causing the ECM to panic. As far as I can figure, the ECM is the only box on the truck that actually serves a purpose.
@trbo6
8 жыл бұрын
I had same thing. right rear turn signal only. No power to other 3 blinker bulbs. Had left headlight on bright and right headlight on dims. Soldered the wire just like you did and it works fine. Dodge service guy said $1700 to fix it. Thank you so much for this video.
@TheJrl1982
9 жыл бұрын
i have a 2002 dodge ram 1500 and was having the low beam issue with no turn signals outside but flashed fast on the cluster panel also said lamp out so i did exactly what you said in the video and it works perfect thank you so much for sharing and saving me about $1000
@brandonstrother5809
6 жыл бұрын
Had the identical problem in the exact location of the board. I was having multiple issues with turn signals, low beams , front and rear. Followed your lead and it worked perfect. No more problems
@daveherriot8608
4 жыл бұрын
Many thanks for this. Had the exact same problem on my 05 ram and now works great again. I tried soldering the trace on the other side but solder would not bond to the board, I'm a rookie at soldering but this was much easier to accomplish.
@betoc1888
8 жыл бұрын
success! its been a few weeks now and everything works flawlessly! thanks a ton for this video!
@cf921moto-x6
5 жыл бұрын
Thanks for posting this it saved me a lot of cash! I had no front turns and 1 out in the rear. This fixed it.
@Justin-bh3dj
5 жыл бұрын
Thanks for the video, worked awesome on my 03 3500. Thanks again
@starskibear
7 жыл бұрын
Worked for me. gonna keep my eye out for a relatively low cost spare from a southern state, mine has several spots that look like they could fail at any time from corrosion
@Mike_Hoellwarth
Жыл бұрын
I think this might be my issue too. I have an 07 ram with no power to the driver side low beam. Haven't taken apart the TIPM yet but I guess that's the next step since there's no fuse for the headlights.
@stanwardoshiro
Жыл бұрын
I have a 2004 Ram in for repair and I took apart the IPM and saw no damage/flaws to the circuit board. I'm now assuming the FCM is the problem.
@terryj.macmullen9968
3 жыл бұрын
a friend has 2007 calibre. head light on passenger side not coming on. lost the ground connection ,it seems . bared ground connection on light socket, connected a ground wire light worked.
@wheyez1
7 ай бұрын
That’s a great rename, you aught to put it in the title. I wonder how many hits you would get for something like that? I’m sure dodge won’t pay attention and make it right.
@prancstaman
8 жыл бұрын
holey shit dude, my kids mini van has problem with headlight, I'll be checking that. Thank you.
@jimfarrell7187
6 жыл бұрын
It would be great if you could give us more specific instruction and description from start to finish. Like wheres the headlight board found and how'd you get in there. Also what board and which of the pins we need to solder the wires to. You know, a little help for us dumb guys that really need good clear instructions.
@jandjmca
9 жыл бұрын
See sprinkles08JACDJ for instructions on taking TIPM apart
@kenosburn2205
6 жыл бұрын
My 98 ram 3500 headlights go out on high beam. Melted 3 light switches....so far.
@CarlMazur
9 жыл бұрын
Class action Lawsuit. Just found this... Possible Recourse & Actions You Can Take If you own or lease a Jeep/Dodge/Chrysler vehicle and are having issues with your vehicle's TIPM, or if you want to learn more about this class action against Chrysler, please contact Girard Gibbs LLP at 866-981-4800 or by email at TIPM@girardgibbs.com
@jandjmca
9 жыл бұрын
I Have the same problem right rear turn signal is only one working and right headlight works but when I hit high beam that light goes out and the other light is on high beam
@rolandvz71able
8 жыл бұрын
what were the symptoms you were having? My dad having issue with headlight burning out....he thinks it may be the connector, but then I came across your vid.....A+ on the vid!
@johnd4348
4 жыл бұрын
My 2004 dodge Ram 1500 had low beam issue. Replaced FCM(Front Control Module) . Fixed problem for 2 months then all my lights went out but one head light and high beams. Yes I checked all the connections under the fuse box. All were tight and I cleaned them the first time with emery cloth even though they had no corrosion on them Then a few days later they started working again. Is it possible that the FCM I installed was OK and its the fuse box circuit board. I'm guessing the remanufactured FCM I installed was defective. But not realy sure. I installed another remanufactured FCM from Rock Auto. Original cost was $341.00, but they give me a $220.00 core refund if I send it back. My understanding is they do not make new FCM. If they did I would have bought one. Could it be the fuse box circuit board? My truck only has 40 thousand miles on it and has spent most of its life in very dry desert climate. No rain or salt .issues
@gregbakley6525
5 жыл бұрын
dodge never could wire , owned them since the 70s they always has some kind of wiring issue
@Ponyreiter
7 ай бұрын
That's why they are a match with Fiat... 😅
@billwilliams6338
5 жыл бұрын
CURT DONAHOO, I'm not sure if a TIPM circuit is just a fuse box or does it convert CAN signals into LIN signals and other signals?
@Labyrnthdom
5 жыл бұрын
Was that burned trace on 1 side of the board? If so, just to help others out. You can remove mask from the thick parts of the trace and attach your jumper there. It would be a shorter jump and larger area to attach the jumper. Just a guess, the jumper to that small pin may heat up a detach. But you wont know until you try right.
@bradt9350
3 жыл бұрын
kzitem.info/news/bejne/uoqLq5uBmoCXYII This is exactly what you are talking about...
@Davilow
8 жыл бұрын
"Design flaw" = Chrysler.
@chrisoman2195
5 жыл бұрын
Davilo Olivad yeah it's cuz their fukin idiots
@mrsemifixit
7 жыл бұрын
Are these TIPMs wired in parallel and sometimes one of the lines go bad so only certain circuits are affected while others continue running?
@gregmann410
4 жыл бұрын
Interesting how did it turn out
@TayAllen54
3 жыл бұрын
Is this the same for a 2016 charger? Do they use the same TIPM
@infowarrior420
7 жыл бұрын
good job
@betoc1888
8 жыл бұрын
my 2004 ram having some light issues aswel, no rear brake lights, no turn signals at all, right front low beam only. Took apart the TIPM and got it down to the board, seen the EXACT same spot in your video (before i seen the video) and assumed it was damage from prying up on the board accidently. wondering if i run a jumper like in the video i can fix this? how did yours turn out?
@TIMEtoRIDE900
8 жыл бұрын
This just happened to my 96 Ram 1500 and now I have 7 days to fix it or $150.00 fine. High beams work and fog lights work. So just jump/bypass the burnt spot ??
@canada19521
7 жыл бұрын
TIMEtoRIDE900
@TIMEtoRIDE900
7 жыл бұрын
It seems I posted alot of "help" requests - - mine just needed a headlight switch.
@tonycastro6154
3 жыл бұрын
a chevy?? same sht...
@tigrisr7503
7 жыл бұрын
don't buy Dodge or Chrysler ever very bad quality cars
@chrisoman2195
5 жыл бұрын
ifixitnow A****A exactly what I say yeah let's put a battery in the wheel well, stupid fucks
Пікірлер: 42