The "dry run", is essential for handheld router work. I use an "outside block" setup for juice grooves but one time I forgot to rotate the router and overshot the square. I saved the project but it hammered home the lesson: do a dry run!
@InspireWoodcraft
Жыл бұрын
@Adam DeJesus 100% agree. I usually do a second dry run nowadays too with material being so expensive.
@egbluesuede1220
Жыл бұрын
I tried this technique on my first ever cutting board and really struggled with it. Your explanation and tips on how to turn that corner are SO HELPFUL! I love how you teach woodworking as well as your creativity. Absolute favorite channel. Thanks!
@dngriffiths8105
Жыл бұрын
Thanks, Jodi, for thinking outside the box and providing another great tip. Your knack for lateral thinking benefits us all.
@loubonaparte5063
7 ай бұрын
I love the thought you put into your approach to finding ways to do things.... no right or perfect way, and not everyone has same arsenal of tools. I like your videos as they're straight forward and to the point.
@sergiobarros2697
Жыл бұрын
Love your videos...no bs talk, straight to the point.....serious professional work and teaching....thx a lot
@BrenQ99
11 ай бұрын
Your stuff is consistently beautiful. We know this. But that particular combination of maple and cherry? Just perfect! Well done!
@TheDrewdaddy44
9 ай бұрын
All of your videos are very easy to watch and super helpful. Your a damn fine woodsman. Thank you
@joelesko3267
Жыл бұрын
Great video man! Literally in the process of making odd shaped boards and your solution certainly solves this problem! Well done sir!!
@ashokmoghe8035
Жыл бұрын
Always learning something from your videos, Jodi.
@TheCankersore
4 ай бұрын
Thanks! As a noob, I learnt a lot from this video. Can you possibly show making a juice groove in an oval shaped board, please? Thanks again!
@johnsanchez1619
Жыл бұрын
Perfect, this was exactly what I needed to help with a curved board. Thanks!
@rickstandifer1714
Жыл бұрын
If you're batching some out, make a jig to place on the outside of the template that is the same size as the work. Use this to align the template each time. I can see it but I'm not sure I explained it well enough.
@mightyporky
Жыл бұрын
I also think your idea is the better way, not much chance of a mistake.
@InspireWoodcraft
Жыл бұрын
@Rick Standifer That's coming in another video. Probably one on how to do trays. I didn't want to stray too much from the juice groove topic, but if I was batching out boards, I would have a full template that lets me cut the outside radius and the inside groove.
@JasonPeltier
Жыл бұрын
I was thinking it would be yet another use for 1-2-3 blocks. I designed some planters a few months ago with a 1" overhang on the top trim and used the blocks to align the pieces.
@guilhermesampaio5318
Жыл бұрын
This is exactly what I was looking for. Thanks, buddy!!!
@MCsCreations
Жыл бұрын
Thanks for the tip, dude! 😃 Stay safe there with your family! 🖖😊
@glencrandall7051
Жыл бұрын
Great idea.👍👍Thank you for sharing. Have a great day and stay safe.🙂🙂
@makermark67
Жыл бұрын
Great video. Lots of great info in this one! Hope you and yours had a great Thanksgiving!
@bobp3738
Жыл бұрын
Well done! I think I’d like a clear base though to see what’s happening with the bit/cut.
@InspireWoodcraft
Жыл бұрын
@Bob P So I was going to make that sub base out of acrylic, but I only had 1/8th inch on hand and didn't want to go to the store. The MDF version has a hole big enough in it that I can see the bit just fine though.
@bobp3738
Жыл бұрын
👍 I’m constantly improvising with what I have to avoid a trip to the store!
@TotalBoat
Жыл бұрын
What a great tutorial!
@jeffreycanfora1091
Жыл бұрын
Perfect Timing 👍🏼 Thank you 🙏🏼
@psycheeight082
Жыл бұрын
Rather than using the “oils from my fingers”, I lightly stick the tape to my (clean) shirt and get more repeatable usability. Just another thought
@Orion9993
Жыл бұрын
Great video, and thank you for all that you do to show beginners like me the best way to accomplish tasks. I do have a question. You mentioned about the burns and to use a "scraper" can you link me one that you use?
@lincolndickerson1293
Жыл бұрын
Great video! Curious what the pros and cons of using the router table instead would be.
@joeprior7311
Жыл бұрын
Great question. I was thinking a router table and fence would be simpler.
@ThekiBoran
Жыл бұрын
The Dewalt trim router's plunge base is much nicer than the makita's. I have both, I know.
@dpmeyer4867
Жыл бұрын
thanks
@PCPAyLOAD
Жыл бұрын
If you really want a challenge try this with a trim router.. good times!
@luvmonkey666
11 ай бұрын
What would your solution be for shapes that curve inward and outward? The shapes I’m working with are all unique so making a single jig is out of the question.
@andrewbrimmer1797
Жыл бұрын
Nice
@dreddy5187
Жыл бұрын
Is that face grain? Are face grain cutting boards that great or should we usually make edge and end grain?
@darthstewie76
Жыл бұрын
I've been thinking of something similar to this but considered using guide bushings instead of a bit with a bearing. Whatever works though!
@InspireWoodcraft
Жыл бұрын
@darthstewie76 Funny you mentioned this. This whole idea came to me by using guide bushings and a regular round nose. Mainly because that's what I already had on hand. Then it occurred to me that I would have to teach folks how to use guide bushings, and that gets confusing, and... yeah. So, I went for the bearing round nose bits instead to keep it simple. That being said, guide bushings work great! If that's what you have, go with it. I like that depending on the guide bushings that you have, you could offset the groove using the same template too.
@tonyweisse3285
Жыл бұрын
@@InspireWoodcraft I like the idea of using a guide bushing, too. I think it might be easier when you plunge the cut since you can rest the bushing on the template for positioning purposes. Good video!
@edkorsberg6441
9 ай бұрын
I do not understand why you don't hold onto the knob handles during the trip around the board. It seems like pushing the base is asking for trouble
@MMWoodworking
Жыл бұрын
That poor little trim router sounds like it is going to drop dead midway through the run that was too deep. I know that sound all too well. When I’m in a rush, and have a ton of dados to do in a harder wood, sometimes I get lazy and try and take most of it in one pass, and it always sounds like a dying animal. Solid video.
@billboy7390
Жыл бұрын
Turned out nice but not the way I do it. I teach my students to do it the opposite way you did and use the waste piece from the middle (cut down an inch smaller all the way around so router can’t tip and use a collar instead of a bearing. We never put the groove closer than 1/2” to edge for double sided tape.
@InspireWoodcraft
Жыл бұрын
@Bill Boy I'm not sure I understand but I wish I did. I'm always open to different ways of doing things!
@silenthill5794
Жыл бұрын
So I was all amped up by your channel..and .....then...you made a cutting board type video :-( I gotta ask, who are these people that are buying all of these damn cutting boards ? Wth ??? And by the way, I own one cutting board, Walmart purchase probably, and the juice grooves NEVER WORK...the juices always pool right in the middle of the board, so this is a flawed design whose only purpose is to dupe people out of their money And yes I"m talking to YOU average you tube guy...get your cutting board out, cut up some tomatoes and come back and tells us how much juice is actually IN the damn juice groove...I'll bet there's none. The only way the juice gets into that groove is if you push it all into the groove, thereby defeating the purpose of the groove in the first place..l'm so tired of cutting board videos, I almost wish this was an epoxy river table video.......almost..../end humor
@InspireWoodcraft
Жыл бұрын
@Silent Hill GASP! Average KZitem guy?! That was a low blow. HA! On a serious note, it's the time of year when lots of woodworkers are making cutting boards and things as gifts and for extra cash for the holidays. And there are lots of folks who are starting out, and cutting boards are still their jam. At any rate, a board this size is perfect for a tri-tip, and the juice from that would definitely run into the juice groove. I have a couple of stains on my counters from resting meat that has drained out onto the counter.
@silenthill5794
Жыл бұрын
@@InspireWoodcraft Nonono, average YT guy was my comment towards the viewers not you lol...sorry too much wine while I was internet ranting, your channels awesome, Im just not a cutting board fan..
Пікірлер: 45