Do you know the pinout for ECU ME7.2 ? Thanks in advance¡
@jaroslavjadrovic6779
5 жыл бұрын
ahoy , potrebujem tak to spraviť simos 3PA . skúšal si aj simens ?
@iamvehicle8596
5 жыл бұрын
V minulosti jsem dělal 3PG ten jde. Ale tady bude nejspíš potřeba použít programátor pokud Galletto nenabízí možnost bootu.
@jaroslavjadrovic6779
5 жыл бұрын
@@iamvehicle8596 ano elnec mám ale cez programator je to zdlhave , robim casto upgrade na tychto jednotkách . Skoda firmware
@ecarruda
5 жыл бұрын
Did you write tuning file ( remap ) or just OEM file back?
@iamvehicle8596
5 жыл бұрын
You can write a tuned or orig file. But in tuned file you must have corrected checksum.
@MKhanfar-MWK
4 жыл бұрын
@@iamvehicle8596 what you mean by correct checksum
@iamvehicle8596
4 жыл бұрын
@@MKhanfar-MWK Each ECU uses a checksum to check the functionality of the software. A new checksum must be calculated each time data is changed. If you do not calculate a new wants, the car will not start. A tool like Kess, calculates a checksum automatically when you flashing. But Chinese tools (Galletto, MPPS) will not. You can see at 5:28 when the program says checksum is not supported.
@MKhanfar-MWK
4 жыл бұрын
@@iamvehicle8596 thanks for clearing ,,, but when I get file with kess then like remove egr using software ( edit ) original file , does after that need to correct checksum before upload it to ecu using kess ? If yes how to correct checksum?
@iamvehicle8596
4 жыл бұрын
@@MKhanfar-MWK Yes, checksum must be corrected. But Kess will do it automatically.
@VELOCETTEify
6 жыл бұрын
What's the name of the music in The background
@mironet8
5 жыл бұрын
kzitem.info/news/bejne/tYGcuWmwj5h4dZg
@racing0eagle
3 жыл бұрын
Hello, i had problem when i was written map in the car (bmw 120d e87) with mpps v16 and had to abort process, now car wont start and mpps shows that the ecu not found and i cannot write my original file in car, what can i do? I tried Recovery slow and full data but no luck, some people say that i must press start buton once because of contact, pushing key is not enough?
@iamvehicle8596
3 жыл бұрын
Your BMW probably has an ECU EDC16. That is something else. There you need to carefully open the ECU and do the recovery through the BDM service port. (Ktag, BDM100, Galletto) MPPS can't do that.
@racing0eagle
3 жыл бұрын
@@iamvehicle8596 thanks, problem solved with ktag
@ottokivisto5122
11 ай бұрын
Hey. I’m posting to this because my audi has same kind of problem. Mpps says ecu not found after programming new software and i’n trying to put the old back in. I have the me7.5 ecu audi a4 b7. Ssoooo, do I need to do this procedure done in this video and does mpps boot mode work?
@comady3925
4 жыл бұрын
But way problem car ecm
@jaremyhawk
5 жыл бұрын
what tool are you using? gletto 1260? or KWP 2000 plus?
Пікірлер: 27