bro having problem with that left small display not able to see number properly they are dissorted
@zakariaechababi8461
Жыл бұрын
Hello, I have the same problem with my 1999 Seat Toledo, would it be fixed in the same way?
@MrGmaros
Жыл бұрын
Thanks this video.👌
@markosusnjar1305
Жыл бұрын
Can you please send me link where you bought FLASH programmer(SOP 44) and does it contain software with it?
@1snakeolha1
2 жыл бұрын
thanks u!!!!! i did the same and work very well :P
@pablopereira7690
2 жыл бұрын
Muchas gracias por el video ; como se lee el pin code? Ya que recien estoy comenzando ,adquiri este mismo programador y quisiera aprender sobre immo off, odometros , airbag .
@bonisyafialdi2286
2 жыл бұрын
What car is it?
@iamvehicle8596
2 жыл бұрын
EDC15 (Skoda Octavia 1, Golf 4, Leon, and next)
@mohamed299
2 жыл бұрын
Good joob
@jesussalcido
2 жыл бұрын
Do you know the pinout for ECU ME7.2 ? Thanks in advance¡
@Jose-rh7sx
2 жыл бұрын
turns it upside down😂
@pomeranc3154
3 жыл бұрын
You have installed your pointers wrong way, you have to turn all of them clockwise until they reach the end of their path, so they can't be turned more clockwisely. Then, after turning your key into first position, they will find their zero position correctly and you don't have to keep trying to set them on your own, which is less accurate. We can see this at the end of the video as they are attempting to find the zero position.
@UrbanRave1982
3 жыл бұрын
I bought an ecu that immo is turned of. Can I take the eeprom from the new ecu and put it on my old ecu? Because the old ecu is chip tuned and good.
@iamvehicle8596
3 жыл бұрын
Yes, you can swap eeprom.
@UrbanRave1982
3 жыл бұрын
@@iamvehicle8596 ok. Good. That’s easier then swapping the tuning chip. And I was affrad that the eeprom was specifically for the ecu. But ok good. And the whole immo on and off is only on the eeprom? So I don’t need to do anything else. Just swap it
@UrbanRave1982
3 жыл бұрын
@@iamvehicle8596 Bought ECU’s are the same. It says 0 261 204 184/185 And then some other says 8D0 907 557 T Only difference is where it says the year. The old says 24.01.97 and bunch of other numbers. And the new with immo of says 11.09.96 and some other shit. But when I open them up. They are identical “of course” But when I look on the components and all the tiny chips that are inside them “they look the same but these is difference on the numbers on them. Does it matter or can I still swap the eeprom??? My original ECU whit chip tuning the eeprom says 67AN B58 258 And the new one with immo off the eeprom says 63AD B58 258 So my question is. Does it matter? Or can I still just. Swap the eeprom over to the “old, original, chip tuned” ECU?
@iamvehicle8596
3 жыл бұрын
@@UrbanRave1982 Yes, you can swap old eeprom to the new ECU.
@UrbanRave1982
3 жыл бұрын
@@iamvehicle8596 and even if the letters and numbers on the eeprom are not identical?
@johanna21ify
3 жыл бұрын
Dobrý deň mám otázku. Ten krém čo tam dávate..čo to je?
@farido9327
3 жыл бұрын
merc
@abdenbielmakhoukhi6757
3 жыл бұрын
hey, your video is really great. I'd like to ask you if it's possible I'd like immodecoding I'm not milk if you want to send it to me if it's possible, thank you
@jozefProperty
3 жыл бұрын
How mach power can be gained from this process?
@FrancoPN
3 жыл бұрын
With this cable you don't need to remove IC from pcb board, save time doing all by IN CIRCUIT, see this video below kzitem.info/news/bejne/mrCp0qeKepOTY6Q
@luckyl623
3 жыл бұрын
Chci se zeptat když to budu dávat zpet do auta budu to muset nějak udělat přes VAG? Jako třeba zadat PIN nebo něco ?
@iamvehicle8596
3 жыл бұрын
Není potřeba.
@waeszx8348
3 жыл бұрын
👍
@TV.AUTOPORADNA
3 жыл бұрын
Zapomel ukazat to hlavni. Ten stabilizator vyhreje obvody, ale uplne nekde jinde. To zakladni Vam nikdo prsve neukaze, kde je problem a dostavi se pozdeji
@iamvehicle8596
3 жыл бұрын
Díky za komentář, každopádně žádné další "obvody" to nevyhřívá, za pět let se mi vrátila na reklamaci pouze jedna přístrojová deska.
@jalosos9366
3 жыл бұрын
Ahoj.Ak to neni tajnost,kde zozeniem chladic TLE?.Ci si si ho vyrobil?
@iamvehicle8596
3 жыл бұрын
e-bay "aluminum heat sink"
@giacomoguajana
3 жыл бұрын
Cosa spalmi prima di dissaldare la eeprom? Grazie
@giacomoguajana
3 жыл бұрын
@@FrancoPN cosi posso fare una scodifica parziale sulla edc15c7?
@agi-vasssoma3354
3 жыл бұрын
I do it same. After immo off car is start but key is flashing on dashboard. What is the solution?
@iamvehicle8596
3 жыл бұрын
Black tape or remove LED from dashboard. Is not solution for this.
@amrosama4280
3 жыл бұрын
And if u get immo light error you must check anttena coil plug remove it and push the two pins to down
@0hjaa3.06
3 жыл бұрын
Is it the same process with a mk1 Fabia cluster?
@iamvehicle8596
3 жыл бұрын
Not, Fabia has other problems.
@Adjanst
3 жыл бұрын
THANK YOU VERY MUCH!!!! I solved my problem by myself, qucker, cheaper and easier than i think. GREAT and VERY HELPFUL video! :-)
@racing0eagle
3 жыл бұрын
Hello, i had problem when i was written map in the car (bmw 120d e87) with mpps v16 and had to abort process, now car wont start and mpps shows that the ecu not found and i cannot write my original file in car, what can i do? I tried Recovery slow and full data but no luck, some people say that i must press start buton once because of contact, pushing key is not enough?
@iamvehicle8596
3 жыл бұрын
Your BMW probably has an ECU EDC16. That is something else. There you need to carefully open the ECU and do the recovery through the BDM service port. (Ktag, BDM100, Galletto) MPPS can't do that.
@racing0eagle
3 жыл бұрын
@@iamvehicle8596 thanks, problem solved with ktag
@ottokivisto5122
Жыл бұрын
Hey. I’m posting to this because my audi has same kind of problem. Mpps says ecu not found after programming new software and i’n trying to put the old back in. I have the me7.5 ecu audi a4 b7. Ssoooo, do I need to do this procedure done in this video and does mpps boot mode work?
@pjson70
4 жыл бұрын
Is this the only way to get the immo revoved from the Car?
@iamvehicle8596
3 жыл бұрын
Yes.
@lizakonvalinkova5504
4 жыл бұрын
Díky moc! Hodně jsi mi tím pomohl 👍
@ViPeRPcGaMeR1
4 жыл бұрын
Can you please tell me, can you read ME7.1.5 (A4 B5, '99, 2.4 petrol) also in boot mode? I have ktag, galleto v54 and mpps v18.
@marekvalal1680
4 жыл бұрын
Ahoj, budu u superba 2. Generace měnit ledky a až to budu skládat tak mám strach aby ručičky neukazovali blbě. Myslíš ze bude fungovat ta tvoje metoda u supa? Tak ze rucicku otočím dozadu, dokavaď to nezačne cvakat a pak zpět na nulu. Nemám diagnostiku tak si to potom nezkalibruju tak jestli radci investovat nemalé peníze za servis nebo si to udělám sám za par korun
@iamvehicle8596
4 жыл бұрын
Můžeš si vyfotit předem přesné pozice u ukazatelů. Pokud to potom složíš tak, jak máš nafoceno, odchylka bude minimální. Samozřejmě je lepší použít diagnostiku.
@dragosvasile8085
4 жыл бұрын
Can the clocks lightning be fixed this way?
@kvacksilver5276
4 жыл бұрын
04:58 Does anyone know where you can buy this screen? Whenever I search for LCD screen I just get the big one in the middle. I won't even consider to ask OE for this.
@eduartcela5598
4 жыл бұрын
I solved my problem watching this video... .. thank you very much
@christianrefle8035
4 жыл бұрын
Hi which pins do I have to energize?
@iamvehicle8596
4 жыл бұрын
Pin 1 +12, Pin 9 GND
@VisarLimani
4 жыл бұрын
Thanks for the video! Which software are u using to immo off after reading from eeprom? Thanks.
@iamvehicle8596
4 жыл бұрын
Immo universal decoding
@VisarLimani
4 жыл бұрын
@@iamvehicle8596 its possible to download it anywhere?? Thanks in advance.
@LOOKATUSCREW
4 жыл бұрын
i buddy, i have the same ecu here but i dont know what type of "liquid" you use to desoldering, can u help me?
@SKZT412
4 жыл бұрын
После всего этого надо положить новый герметик и закрутить , старый герметик держать не будет и при попадании влажности блок умрет.
@iamvehicle8596
4 жыл бұрын
MSA15, EDC15 does not need a new sealant. Tested on many ECUs. Newer EDC16 and EDC17 needs sealant.
@sforman2622
4 жыл бұрын
Dobře ty! Zkus i VAG-Commander. Vyčteš loginy immo budíků bez pájení.
@iamvehicle8596
4 жыл бұрын
Díky. Commander je dost omezený nástroj, lepší je FVDI.
@sforman2622
4 жыл бұрын
@@iamvehicle8596 dík, vyzkouším
@k2008krzycho
4 жыл бұрын
Doskonałe. Szkoda tylko ze nie jest to po Polsku :(
@Kurzac_Classics
4 жыл бұрын
Przecież to jest w "żadnym" języku 😁
@Adjanst
3 жыл бұрын
Naprawiłem swoje zegary w polifcie na obiadowym stole, bez głośników, nie były potrzebne. Wszystko jest pokazane.
@radoslavorevic4397
4 жыл бұрын
super prikazano
@mohamedarrche4797
4 жыл бұрын
Ok
@paulofonseca7550
4 жыл бұрын
Nice Video. ;) In the AM29F400BT you can save the original file or Repro directly on the chip? or is it necessary to have some car data? What data is written on AM29F400BT and what data is recorded on 24C04? Regards
@comady3925
4 жыл бұрын
But way problem car ecm
@astroboy2astroboy247
5 жыл бұрын
very good thanks the car started before repair
@dabijaciprian3362
5 жыл бұрын
Sall spunetimi si mie cum se cheama cele 5 buline portocalii ( sunt 5 sigurante ) 12 v fiecare un nume mai concret ms
@vehicledoctors7834
5 жыл бұрын
Very very thank you👉
@petrlangmajer8448
5 жыл бұрын
servus, prosim tě to jsi toho švába vyměnil nebo jen proletoval a přidal chladič?
@iamvehicle8596
5 жыл бұрын
Pouze přepájet, měnit není potřeba.
@Cr0sfad3
5 жыл бұрын
Thank for your video! Sry for bad english and noob questions, what flux you use, and temperature?
@Cr0sfad3
5 жыл бұрын
@@iamvehicle8596 thank you wery much!
@alind2107
5 жыл бұрын
Thanks for sharing the knowledge, and please use cotton gloves (no greasy finger traces). "Speed needle is a little ahead." -> see below... "But just about 5km / h. It is well" -> you were lucky. Once dismantled, just power the dash before putting it all together. 1. Mark the pins at "zero" 2. Adjust the position of the pin with a precision plier to match the assembling position 3. Assemble needles and pin each one to it's corresponding "zero"
Пікірлер