For anyones benefit this will not work this easily on a mother boards of version 1.1.4 or earlier. For that you will need to put a bootloader on the board first.
@techs.passion
8 ай бұрын
Thank you so much, you are correct 💯 let me pin this comment
@Charlesbjarvis
8 ай бұрын
Bootloader? As in?
@techs.passion
8 ай бұрын
Basically you need to compile the firmware first to get the bootloader if you have the old version of the board
@puneethsrisai
3 ай бұрын
i bought ender 3 in 2018 and it has v1.1.3 . Recently i tried to make some changes and flash the firmware with SD card but it's not working. why is it so ? what changed? in 2018 i never faced such issue
@nousagi7437
26 күн бұрын
Good observation, this relieved many recent head scratches
@igoreq4495
7 ай бұрын
This fixed my blank screen issue, very fast and effective, you are amazing
@techs.passion
7 ай бұрын
That's good to hear, glad it worked. Thanks for watching
@Papawheelie57
11 ай бұрын
You are the man! Simple instructions that are very clear no bs
@techs.passion
11 ай бұрын
Thank you, that's exactly my intention and goal for this channel
@techs.passion
Жыл бұрын
Hi everyone, Here is another helpful video regarding the SD card kzitem.info/news/bejne/tqNpnHmisoaZhmk
@CecalaLandscapeandMasonry
7 ай бұрын
what about ender 3 pro? there are a lot of options and im not sure what to chose. I have a 4.2.2 and i installed a cr touch. what firmwares do i choose? thank you
@techs.passion
6 ай бұрын
Go under the CR touch and choose the one for your motherboard version. I have a video showing it, let me see if I can find that for you, one second
@techs.passion
6 ай бұрын
Use this video kzitem.info/news/bejne/sop4xYSCqpulen4 jump to the part where I download the firmware, I hope it helps, I might make a separate video just for this because I get this question a lot. Thanks New video kzitem.info/news/bejne/la-cv4t-moV6gIY
@Jrobam
3 ай бұрын
Thank you very much! It was exactly what I need! A simple way to fix my problem with the fimware! There are a lot of videos talking about a lot of information for more complex solutions, for today, your solution was the best! Thanks!
@techs.passion
3 ай бұрын
Thank you so much, I'm glad it was helpful and my intention was exactly that. I'm sure there is a need for a more detailed video as well
@Jrobam
3 ай бұрын
@@techs.passion no, I think it is perfect. If you make a more detailed video it should be for other purposes. Some people want to tune Marlin, etc, but there people like me today, just needing a simple solution. This video it's perfect for that purpose
@techs.passion
3 ай бұрын
Thanks again 👍 I appreciate it ☺️
@angieuesselerc
Жыл бұрын
Nice video, super clear! I wanted to know the micro SD card must be clean of any other file or it can keep the info with the firmware update? thank you!
@techs.passion
Жыл бұрын
Hi, it doesn't need to be clear although it is recommended. As long the MicroSD is formatted correctly and you have the firmware file in the first level not inside folders it should work. That said if the printer not picking it up, it might be because of the way it's formatted or could be the other files in there impacting it. I would try with other files but have a back up of your files on your PC first, add the firmware outside in the root and not deep in the folders structure and if that didn't work I would format the card FAT32 then try with only the firmware in it. Sorry if that was confusing. Short answer, No but it is recommended. Thank you for watching and the nice comment :)
@techs.passion
Жыл бұрын
Hi, I hope you find this helpful kzitem.info/news/bejne/tqNpnHmisoaZhmk
@MikomiKawaii
2 ай бұрын
Thank you! Super simple tutorial and it worked well for my printer. I have never updated the firmware (cant lie had no idea I had too lol) and I have had this printer for almost 4 years lol
@techs.passion
2 ай бұрын
Glad it helped! Thank you for watching 🙂
@steveo2737
3 ай бұрын
I recently purchased this printer and trying to do all the upgrades but when When trying to install the CR Touch firmware for my Ender 3 (v1) 4.2.2 board (Firmware 2.0.1), it changes my main firmware backward to 2020 (Ver 1.1.2) when it boots when loading. I have flashed back to the current firmware (Ver 2.0.1) but it keeps happening every time I flash it again. Mainboard Version: V4.2.2 Ender-3 Marlin2.0.1 - V1.1.2 - ALT(32bit) CR Touch Version: Mainboard Version: V4.2.2 Ender-3 Pro Marlin2.0.1 - V1.1.2 - ALT(32bit) What am I doing wrong?
@techs.passion
3 ай бұрын
Hi, based on this it sounds like you might have more than 1 firmware on the SD card. Try to get a clean freshly formatted SD card then add only the firmware you want on it. I have a full CR touch video on my channel which should help, just type cr touch techspassion in KZitem.
@theoneshopbroshop
3 ай бұрын
This is what I have been needing it was short simple and did not have any other useless information I will immediately like and sub
@techs.passion
3 ай бұрын
Thank you so much, that is my goal and glad you like it :)
@cesarmartinez6708
11 ай бұрын
Hi, i followed your procedure and everything worked (successfully installed Marlin 2.0.6), but now nothing works, it only heats up. I just get the error message: " homing failed: printer halted please reset". Can you help me out?
@techs.passion
11 ай бұрын
Hi, Sorry to hear that. I have seen this error and from what I know it is related to the End Switches so I would check those first. Restart the printer might help sometimes after the firmware is updated. What is the printer model and MB version? I will do a bit more digging for you
@cesarmartinez6708
11 ай бұрын
@@techs.passion Thanks for getting back to me. Yea i restarted a few times and kept getting that error message. Ok i will look into that after work and follow up with the MB version, the model is just the Ender-3 (Not V2, Pro, etc.) Please let me know if u find anything helpful. Thank you!
@techs.passion
11 ай бұрын
I did bit more research and keep me posted I'm sure you will figure it out but this error is due to the printer not knowing the current position one or all of the axes. First, check that all switch buttons can be reached without a problem and there is no cable or problem with the 3 switches. If all switches look good, cable connected and all can be reached and you can hear the click then it is the Firmware. sometimes a currupt firmware or the wrong version can be the issue. you might need to re flush the firmware and ensure you got the correct version.
@thomiiik_____5017
10 ай бұрын
@@cesarmartinez6708 any updates? Ive ran into the very same problem just now, have checked everywhere and i still cannot figure out where the problem is
@cesarmartinez6708
10 ай бұрын
@@thomiiik_____5017 Yes, it eventually went away (idk what fixed it, i think just letting the printer off for a while after doing the update). However, it was not extruding properly so i replaced the entire extruder and everything was fine for the first few layers of a test print until it messed up again. my next step was to trouble shoot the E-steps, but i got over it and just invested in a new printer. i have been using a P1S from Bambu Labs and everything is going good (so far lol)
@jamesbarrett6581
2 ай бұрын
What firmware did you have before you did this? The only numbers I can find are 1.1.6.2. I can’t find anything about marlin or 4.2.2.
@techs.passion
2 ай бұрын
Well it depends on your motherboard version, if yours is the 1.1.x.x then this method will not work for you This will work if you have 4.2 or 4.7
@jamesbarrett6581
2 ай бұрын
@@techs.passion thanks that’s what I needed to know. So, I need to do the bootloader stuff mentioned in other comments then? If it’s 1.1.x.x something?
@techs.passion
2 ай бұрын
That is correct, and I'm sorry I don't have a video showing that which I should.
@phantomzoneminecraft6120
9 ай бұрын
So I literraly just plug it in? It was not like that for my printer, nothing happened are you sure there is no other step?
@techs.passion
9 ай бұрын
I'm sure unless you have the very old motherboard, what's your motherboard version?
@CRno25
7 ай бұрын
I have the 4.2.2 board. What’s the difference between this and the default(4.2.2) board? I also just got the cr touch, do I need to update firmware or can I just download the cr touch firmware?
@techs.passion
7 ай бұрын
Hi, This should work for 4.2.2 This will not work if you have the old version 1.x.x Yes, you will need to update again for the cr touch. I have a full video for that Same method should work for the cr touch but you need that file
@CRno25
7 ай бұрын
@@techs.passion Thanks for the reply, I end up downloading marlin using your tutorial and it worked perfectly :D. I tried the same with the cr touch but when I turn on the printer it stays stuck on a blank blue screen. Do you know how to fix this?
@techs.passion
7 ай бұрын
I'm glad it worked out. As for the cr touch, did you install the cr touch and unplugged the z switch?
@techs.passion
7 ай бұрын
I do have a full video showing cr touch installation, highly recommend it
@lifestylerevolutionizer3539
22 күн бұрын
Thanks, you just saved me from a headache.
@techs.passion
22 күн бұрын
Glad to help
@Zombie23Maniac
Жыл бұрын
I noticed yours is like mine. I just put my 3D printer together and videos say you need to click on prepare to fix the leveling, however, mine doesn't have prepare. I've went down a rabbit hole, and other videos are saying i need to download new firmware which brought me to you. Obviously yours doesn't have prepare either, so what the heck am I to do?
@techs.passion
Жыл бұрын
You came to the right place my friend, you do not need a new firmware, if it's a new ender 3, just put it together and then level the bed. Make sure the bed springs are about the same level and the nazal is aligned with the bed. Now auto home, this should be an option to auto home, then use the old style method of paper to level the bed. You can Google it, I'm assuming you don't have CR touch so just the default setup for ender 3 then just level the bed using a sheet of paper, look that part up, it's really easy. Let me know if you get stuck, happy to help:)
@Zombie23Maniac
Жыл бұрын
@@techs.passion I really appreciate the info! 🤙🏼
@techs.passion
Жыл бұрын
For sure, if you still need help don't hesitate to reach out
@MichaelChin1994
10 ай бұрын
Thank you for this video What a wasted day. I've been trying to figure out how to flash the firmware when I could just do this! Better late than never. Seriously. Thank you.
@techs.passion
10 ай бұрын
Glad I could help and thank you for watching 😊
@FabioRVale
Ай бұрын
Works like magic, thank you so much.
@techs.passion
Ай бұрын
Glad you found it helpful
@os-dv1cn
6 ай бұрын
Thanks bro im following ! Just left a 30 minutes vidéo saying that it was too long to find yours 😂
@techs.passion
6 ай бұрын
Glad you found it helpful and thanks for watching ☺️
@flufflepimp2090
6 ай бұрын
Good LORD. Thank you sir. This was NEEDED
@techs.passion
6 ай бұрын
Glad I could help, thanks for watching
@Jtazuniga
19 күн бұрын
i have a question, after I flash my printer, and press auto home, the screen says HOMMING FAILED, PRINTER HALTED, what's that for? how can I fix that?
@techs.passion
19 күн бұрын
Hi, sorry to hear. This could be because the printer not knowing the location for some of the steppers. Restarting should solve it and make sure the end switches work
@MiguelAngelAristizabalPosada
Күн бұрын
Found this was for a 4.2.7 board and yours may be 4.2.2
@techs.passion
18 сағат бұрын
I have tried it on 4.2.7 it's working fine for me and I think it should work on 4.2.2 however it will not work for the 1.x.x boards
@Ksaroko
2 ай бұрын
exactly what im looking for thx hope that will fix my problem. my printer wont start moving even if it seems to be heated up and everything, all the steppers are working aswell and the whole extruder is new (mk8)
@techs.passion
2 ай бұрын
I'm glad you found it helpful, let me know if you need further help. Thanks for watching
@curtiscoulson2994
2 ай бұрын
Any info regarding the bootloader??? Just updated to this firmware as per video, now my stepper motors dont work at all! My board version is V4.2.2
@techs.passion
2 ай бұрын
This should work for your version, it will not work for version 1.x.x but should be fine for you if you got the right firmware file
@-borutosweb-9552
Жыл бұрын
Fine,clear,efficient,you are the best (printer ok now)
@techs.passion
Жыл бұрын
Glad I could help, please do not hesitate to reach out if you have any questions. Thank you for the nice comment and for watching :)
@hexagonal7708
Жыл бұрын
What is supposed to happen after inserting the SD card and turning on the PS? The screen turns on but shows nothing, just blue, should I wait?
@hexagonal7708
Жыл бұрын
ok, i forgot to format the sdc, i tried again but doing everything as you said, it work perfectly!! thanks
@techs.passion
Жыл бұрын
Yes, you should wait a few seconds then it should automatically start after that. The update is fast so you shouldn't have to wait long
@MiloToyne
3 ай бұрын
Hey I don’t understand why other printers online or KZitem on their Ender 3 they have prepare and no TF card can someone explain please
@MiloToyne
3 ай бұрын
Also if it helps the printers motherboard is a v4.2.2 and I am completely new to the hobby so could use some help thanks a lot
@techs.passion
3 ай бұрын
Hi, depends on the firmware version, are you asking why they are not printing from the SD card?
@MiloToyne
3 ай бұрын
@@techs.passion I just don’t understand how my display is different to yours if it is the same printer sorry if I’m missing something
@techs.passion
3 ай бұрын
Oh got it, this is just the firmware version. Mine and yours are not the same which impact the display. I hope that helps.
@MiloToyne
3 ай бұрын
@@techs.passion ok thanks
@carlosorta9179
8 ай бұрын
thanks for this great information in a very short video, it works right away.
@techs.passion
8 ай бұрын
Glad you found it helpful ☺️
@LuciaAlcantara-fi4cd
4 ай бұрын
Hello, I changed the board to my ender 3, the board is Creality 4.2.7 and when I put the necessary file in the SD for it to turn on, it does nothing, the screen stays blue, then in the SD it creates a file called EEFROM and nothing else is no longer please do someone who can help me THANK YOU
@techs.passion
4 ай бұрын
Hi, Sorry to hear that you are having issues. A few thing to keep in mind. Ensure you have the correct firmware, I have a video showing you which one to choose. Make sure the Micro SD is formatted to FAT32 and you are not using a too large one. Make sure the firmware file is in the root. Here is a video that might help kzitem.info/news/bejne/tqNpnHmisoaZhmk
@alexmrcerjace2918
11 күн бұрын
Hey, after doing this my ender-3 doesn't move. It's like the instruction of moving doesn't reach the motors, any help please
@techs.passion
11 күн бұрын
Hey, sorry to hear that, you might have installed the wrong version of the firmware. What's your motherboard version?
@alexmrcerjace2918
9 күн бұрын
@@techs.passion I have the 4.2.2, I put the right bin and it didn't work, then I tried with the 4.2.7 and didn't work either (here, obviusly bc it wasn't the right hardware but i did to give it a try). But once here the printer ignores the 4.2.2 bin file and is stuck at 4.2.7, I think if i erase somehow everything like a factory restore it may accept the 4.2.2 file and work finally, but I'm stuck here
@techs.passion
8 күн бұрын
Yeah I think you just need to try again with the original firmware for the 4.2.2 Also if you want, join my free discord, I will try to help you there. It's free discord.gg/FgVJYEUEXs
@sergiomedina7890
4 ай бұрын
Worked perfectly for me thank you so much
@techs.passion
4 ай бұрын
Glad it helped, thanks for watching
@MartyMarbles
Жыл бұрын
My motherboard is a 4.2.2 and it’s not updating with the 4.2.2 firmware, i tried with the way you did on the video and it worked for a bit then had errors with “homing failed printer halted please reset” then i tried uploading a different firmware and now nothing is uploading
@techs.passion
Жыл бұрын
Hi, do you have CR touch installed? I have seen that error with the CR touch. I think I can help, can you tell me which firmware version you used?
@MartyMarbles
Жыл бұрын
@@techs.passion i do not have the cr touch installed, i do not have any additional accessories, it’s just all the basic equipment, right now the screen says “Marlin Ver 1.0.1 2020-04-25”
@techs.passion
Жыл бұрын
So the error is due to the printer not knowing the current position for all or one of the axes. First, check that all switch buttons can be reached without a problem and there is no cable or problem with the 3 switches. If all switches look good, cable connected and all can be reached and you can hear the click then it is the Firmware. sometimes a currupt firmware or the wrong version can be the issue. Is your printer ender 3 with 4.2.2 board, did I get that correct? you might need to re flush the firmware, let me know and I will find the recommended version for your printer.
@techs.passion
Жыл бұрын
Here are a couple videos might help: kzitem.info/news/bejne/sKet26ejkKlqaqQ kzitem.info/news/bejne/tqNpnHmisoaZhmk
@MartyMarbles
Жыл бұрын
@@techs.passion it was the wrong firmware and i had to clear out my SD CArd, rename the file with 8 characters or less and it fixed the issue
@Ender3Dptints1-i5e
6 күн бұрын
Its works! But I got the error about it not homing? Any help?
@techs.passion
6 күн бұрын
Did you try to restart it? can you post the error message you are getting?
@MiguelAngelAristizabalPosada
Күн бұрын
4.2.2 Board user may get an error while using this, when trying to auto-home
@techs.passion
Күн бұрын
From what I know, a restart can resolve the issue. If you know other helpful solution please share it. Thank you for sharing the info.
@vax_ta
5 ай бұрын
how long need for update? on my ender 3 pro now gone 5 min
@techs.passion
5 ай бұрын
It should be very quick, less than 1 minute for sure
@vax_ta
5 ай бұрын
@@techs.passion I reflesh and it's done now works fine thanks
@techs.passion
5 ай бұрын
So glad it worked out for you. Thank you for watching
@estefaniadesireeavalosrive1056
Жыл бұрын
I insert the sd card with the .bin and the printer loads up but does not do anything. just loads up as always
@techs.passion
Жыл бұрын
This means the firmware is not there correctly or it's the same as the one you already have. Make sure to add the unzipped firmware file at the top level and the SD card is formatted correctly. Give me a second, I have a good video to help you onn that. I will share it here.
@techs.passion
Жыл бұрын
Here are a couple videos might help: kzitem.info/news/bejne/tqNpnHmisoaZhmk
@estefaniadesireeavalosrive1056
Жыл бұрын
I dont think it already has the firmware the one i have is from 2018 and never touched it from there
@estefaniadesireeavalosrive1056
Жыл бұрын
Mine is not pro or anything just ender 3
@techs.passion
Жыл бұрын
My guess is you only need the to ensure the file is in the SD high level and also the SD formatted correctly also, use good quality SD card and not too large size. When I say SD I mean the micro SD card. Let me know if you still stuck, I will try to further help.
@AndrewAHayes
Жыл бұрын
So they must come with a bootloader now as the original ones didnt have a bootloader or thermal runaway protection, that might be why other videos are so long. I ended up using an ISP programmer to update mine and then used rhe PIN 23 board made by Creality to add a BL Touch but then the lid would no longer fit on the printer as the PIN27 board was in the way so I had to make a riser with joined sidewalls to be able to get the lid back on
@techs.passion
Жыл бұрын
Good point, I think that is the case. I updated mine and I thought I put a quick video about it. Interesting, I only changed the board from the 4.2.2 to the 4.2.7 to get the steppers to be silence and that worked out well. I thought about the touch screen but didn't want to spend the money. How long have you had your printer?
@AndrewAHayes
Жыл бұрын
Ah! its the silent board, I thought you were using the stock board, I bought one Ender 3 about a month after the launch and I bought a second one in early 2019, I already had an Ender 2 and a CR-10 before the Ender 3 purchase, that Ender 2 is the most reliable printer I own, its only upgrades are some yellow springs and then silicone spacers and a metal extruder, I also did the Luke Hatfield hotend mod with a peice of original Capricorn PTFE tubing, despite having a printer costing 20 times the price of the Ender 2 It is definetly my most reliable machine, I just press print and forget about it, knowing full well it will deliver a slow but perfect print. I think it is because it so simple there is a lot less to go wrong with it.
@techs.passion
Жыл бұрын
Gotta love a reliable printer. My ender 3 did really well for the first 2 years then it started messing up a bit after that I went with so many upgrades and now it's perfect again. I'm looking into buying the max, maybe if I get a discount on that would be nice.
@dustybahLs
3 ай бұрын
u know the model and board version info for any printer u have to update regardless so if people dont know that they should do some checking !
@techs.passion
3 ай бұрын
Yeah I agree, thanks for watching
@brunoschoofs3951
5 ай бұрын
thanks man for the explaining
@techs.passion
5 ай бұрын
Happy to help
@ReRunTyson
10 ай бұрын
Although this a good way to update firmware it’s best to take the time and look through the code to make sure safety features are activated. Such as thermal runaway.
@techs.passion
10 ай бұрын
To be honest with you I do not know what that means but I will do some research and I might make a video about it if I learn enough to share. Thank you for pointing it out :)
@ReRunTyson
10 ай бұрын
@@techs.passion thank you for being honest. Thermal runaway is a safety feature in the code that will detect if your hotbed gets too hot. If it does it will shut off the printer so that you don’t burn the printer down and your home. That why you see some horror stories about printers burning homes down. It’s because thermal runaway was not activated in the code. For some reason manufacturers love turning it off.
@ReRunTyson
10 ай бұрын
@@techs.passion if you wanted to test wether or not it is activated you can just pull the thermistor out of the heater block and heat up the hot end. If it throws a code on the screen you’re good to go if not I would suggest you look into the Marlin code and activate it.
@techs.passion
10 ай бұрын
Thank you, I will make a video about it hopfully it helps someone out. I will mention this comment. Thank you for information
@techs.passion
10 ай бұрын
Thanks again kzitem.info/news/bejne/tH2Bt4xmrKGTp3Y
@HippyHouse
Жыл бұрын
Does this update work with BLtouch?
@HippyHouse
Жыл бұрын
nvm...i read lol
@techs.passion
Жыл бұрын
Hi, It's similare but different firmaware version but not exactly the same.
@HippyHouse
Жыл бұрын
@@techs.passion I seen there was a BL touch version too. Unfortunately it didn’t boot load like yours did smh
@HippyHouse
Жыл бұрын
Im all stock
@techs.passion
Жыл бұрын
That sucks, let me research that one for you. Sorry to here, I will update you here soon. I have never installed a BL touch but I will do a bit research and come back to you. What is your printer type and board version?
@PowerOfYouth652
7 ай бұрын
It doesnt take time for it to down load nor does it say settings stored just says ender 3 ready
@techs.passion
7 ай бұрын
Correct, It's usually very quick
@PowerOfYouth652
7 ай бұрын
@@techs.passion but that's the problem 😕 it did not download the firmware
@techs.passion
7 ай бұрын
I see, make sure the file is at the top level on the sd card and the card if FAT32
@Acatdrinkingtea
2 ай бұрын
im rocking with 1.1.8 and its not doing anything for me just booting up as normal
@techs.passion
2 ай бұрын
This will not work for your version, you need to compile your own firmware, thank you and sorry for not making that clear in the video
@Acatdrinkingtea
2 ай бұрын
@@techs.passion is there a good video I could follow or can you explain how I can
@techs.passion
2 ай бұрын
While I don't have one on my channel, I'm sure there are some on KZitem but I will try to make one soon as well
@quntun9780
3 ай бұрын
If I only get a blue screen. What should I do next?
@techs.passion
3 ай бұрын
Check the SD card, if it's formatted correctly FAT32 and put the firmware file at the toot and unzip it
@areejshalwani3006
11 ай бұрын
Great video! I was downloading the wrong firmware all this long. Thank you
@techs.passion
11 ай бұрын
Glad I could help
@Jtazuniga
4 ай бұрын
bro, you are amazing, thank you so much
@techs.passion
4 ай бұрын
Glad it helped, Thank you for watching
@nathantelford8333
3 ай бұрын
Nice and easy. Thank you.
@techs.passion
3 ай бұрын
You are welcome 😊Thank you for watching
@Deansley
5 ай бұрын
Thank you!
@techs.passion
5 ай бұрын
Glad you found it helpful. Thanks for watching ☺️
@ThePureblood93
9 ай бұрын
What about the 1.1.4 boards?
@techs.passion
9 ай бұрын
Good question, you need to compile your own software for that, maybe I should make a video about it. Thanks for watching
@RzorFox
8 ай бұрын
@@techs.passion Yes please do! I'm wondering about that too!
@techs.passion
8 ай бұрын
Added to my list, coming soon. Thank you
@puneethsrisai
3 ай бұрын
any solution for v1.1.3 melzi creality board ender 3
@Jaymodtm
2 ай бұрын
I bricked my 3d printer following your ur tutorial…
@techs.passion
2 ай бұрын
Sorry to hear that, I'm sure if you get the correct version it should be fine and it can be corrected. If you want to provide more details, I will be happy to try to help
@Jaymodtm
2 ай бұрын
@@techs.passion i just contacted support and they actually help i apologize for blaming u for my stupidity i was upset
@techs.passion
2 ай бұрын
It's all good, no worries. I only wanted to help if possible. Glad you got it figured out. Do not hesitate to reach out if there is anything I can help with. KZitem comment or Discord, I will always reply.
@crieliocriel
6 ай бұрын
What is your motherboard number?
@techs.passion
6 ай бұрын
4.2.7 is my ender 3
@crieliocriel
6 ай бұрын
@@techs.passion motherboard number..
@techs.passion
6 ай бұрын
Hi, I don't know what the number is, maybe this is something I should research and learn about. Do you mean like 8 or 32 bit? If so, that is 32 otherwise maybe this is something I need to learn. Thanks
@crieliocriel
6 ай бұрын
@@techs.passion nope.. its like this.. GD32F303RET6.. i was told that this is an obsolete model.. so i am going to cahnge mine and the fact that my printer is not working anymore..i guess because or short due to no grounding. because i always get a mild shock when i touch my printer
@techs.passion
6 ай бұрын
I see, Yes I don't really know mine in this case. Thanks for explaining. From what I can guess is you might have a power supply issue or maybe it's not connected correctly. I hope you get it figured out soon and be careful with all the shocks.
@seemaparvezshaik2541
8 ай бұрын
Thankyou so much!!!
@techs.passion
8 ай бұрын
Glad I could help, thanks for watching
@KeepoHdee
Ай бұрын
THANK YOU
@techs.passion
Ай бұрын
I'm glad you find it helpful :)
@pretzelbreadgaming
9 ай бұрын
so i had updated the firmware for the Cr touch but it didn't work how i would have liked it to and now i cont get rid of the crtouch firmware and its not downloading the ender-3marlin2.0.6hw4.2.2.bin
@techs.passion
9 ай бұрын
Sorry to hear that, so try to reverse back to the original firmware, you should be able to do that the same way. Are you getting any errors or what does it say when you try to update to the old firmware?
@pretzelbreadgaming
9 ай бұрын
@@techs.passion it actually doesn’t say anything it’s like it’s not even downloading anything at all it just stays on the updated firmware that I don’t want and thanks for getting back to me
@techs.passion
9 ай бұрын
I see, this could mean that the firmware file is not in the right place or the SD card might need to be formatted. It's basically not recognizing it. Look up a video I have about the SD card. Let me share it here quickly. Of course, I will always try my best to help
@techs.passion
9 ай бұрын
kzitem.info/news/bejne/tqNpnHmisoaZhmk
@pretzelbreadgaming
9 ай бұрын
@@techs.passion ok thank you I will let you know if it worked or not
@eugenc1978
9 ай бұрын
Well done... All others just complicate witd that. I was finished in 2 minute....
@techs.passion
9 ай бұрын
Thank you, that's my goal, glad I was able to help
@tierradelcartel5142
9 ай бұрын
It's more complicated than that. This video does not take into account that most people have the BL Touch auto bed leveling. This will update yes, but if you have a BL Touch, all the settings for the offsets need to be set again.
@techs.passion
9 ай бұрын
You are correct, this video showing how to upgrade/install the firmware but not to adjust the settings after that. To your point, I have this video more about that kzitem.info/news/bejne/kbCOyZqBr6qmZZw Thank you for pointing this out and for watching :)
@giaopx
9 ай бұрын
Obviously, this video does exactlt what it said. Why you even complain
@techs.passion
9 ай бұрын
Thank you for watching
@superduper5530
3 ай бұрын
this method worked for me
@techs.passion
3 ай бұрын
Glad to hear it, thanks for watching
@n.r.2258
8 ай бұрын
There are 13 different Ender3 models popping up … a little more precision would have been helpful instead of quick and dirty.
@techs.passion
8 ай бұрын
Thanks for your feedback, while I agree with you and I have more in depth videos about that. The purpose of this video is to show you how to update in a quick way and assumes you know your printer model and type
@Lisak_.
4 ай бұрын
not work move Axis
@techs.passion
4 ай бұрын
I think I need more details for that, can you provide more details please?
@urbanpatriottactical8717
6 ай бұрын
Didn't help me. My printer does nothing!!!!!
@techs.passion
6 ай бұрын
Sorry to hear that, what's your motherboard version? Let me try to help
@urbanpatriottactical8717
6 ай бұрын
@techs.passion I just installed a mb 4.2.7 with bl touch. I download the firmware and copy it to an sc card. Once inserted into the printer and turned on it just has a blue screen. After about 1 minute the screen will blink making weird noises until I shut the printer down.
@urbanpatriottactical8717
6 ай бұрын
SD card.
@techs.passion
6 ай бұрын
I see, did the motherboard pre installed firmware worked first, did you try that? It could be just the firmware you are choosing, I recommend trying the default one first then see if you can install the one with the bl touch
@nicola3444
7 ай бұрын
The reason why some videos are a lot longer is that they are produced by people with full insight into how the technology works. Your two minutes ended up being 4 hours of readings posts, watching videos and calling friends in order to fix it after following your advice. Pls consider to hold back your videos until you know what you are talking about.
@techs.passion
7 ай бұрын
Sorry to hear that it didn't work for you and thanks for the feedback. I'm always trying to get better
@reinerrosin
6 ай бұрын
I love you for this comment. I am tired of watching videos from people sharing knowledge that they don't have. Short videos are great, but short videos without informations are useless
@techs.passion
6 ай бұрын
Thanks for the feedback, I'm always learning to get better and trying to improve
@neiljohnermac
3 ай бұрын
A simple straightforward video that produces results. Not sure what's so complicated that resulted in 4 hrs of additional time.... perhaps your printer has other underlying issues.
@tvdinner7593
2 ай бұрын
@@reinerrosin how did you not understand the video lmao
@charli384
3 ай бұрын
DOSNT WORK
@techs.passion
3 ай бұрын
Happy to help if you want to provide more details?
@HolyOnigiri
7 ай бұрын
you saved my brother bootyloushus booty thx mate
@techs.passion
7 ай бұрын
So glad I could help, thank you for watching :)
@clintstathis
7 ай бұрын
Didn't work
@techs.passion
7 ай бұрын
Sorry to hear that, what is your motherboard version? if it's the 1.1 then it will not work but for anything start with 4 then it should be fine. Maybe it's the SD card
@quazzi5345
9 ай бұрын
i love you
@techs.passion
9 ай бұрын
I love you too, thanks for watching
@AceHardwareOfficial
5 ай бұрын
my printer is now Chinese helop=
@techs.passion
5 ай бұрын
It's easy, you should be able to just update the language from within the printer.
@happyngrateful
11 ай бұрын
Thank you
@techs.passion
11 ай бұрын
Happy to help, thanks for watching 😊
@LuciaAlcantara-fi4cd
4 ай бұрын
Hello, I changed the board to my ender 3, the board is Creality 4.2.7 and when I put the necessary file in the SD for it to turn on, it does nothing, the screen stays blue, then in the SD it creates a file called EEFROM and nothing else is no longer please do someone who can help me THANK YOU
@techs.passion
4 ай бұрын
Hi, Sorry to hear that you are having issues. A few thing to keep in mind. Ensure you have the correct firmware, I have a video showing you which one to choose. Make sure the Micro SD is formatted to FAT32 and you are not using a too large one. Make sure the firmware file is in the root. Here is a video that might help kzitem.info/news/bejne/tqNpnHmisoaZhmk
@LuciaAlcantara-fi4cd
4 ай бұрын
@@techs.passion Okay, thank you, I'll try it. I haven't been able to use the printer for 10 days 😔
@techs.passion
4 ай бұрын
Dang, that sucks. I hope this helps. Also try my discord, I'm there and I will help for free Discord: discord.gg/FgVJYEUEXs Someone was having a similar issue and we adressed it there.
@LuciaAlcantara-fi4cd
4 ай бұрын
But I don't speak English I'm using a translator hehe
@techs.passion
4 ай бұрын
I see, well I will try my best here. Let me know if I can help and good luck
Пікірлер: 249