Thank you for the video. One thing I’m missing is how do I prime the dampers? I’m not getting the ink to flow. Thanks!
@MayorJordan
2 жыл бұрын
Where did you buy the damper kit and what’s the cost of it?
@adamnagy9512
4 ай бұрын
i have an epson p600 and it looks exactly like your printer.I believe the motor on the top of the damper unit is there to pump the black inks when you change from photo black to matte black as there are no separate "nipples" on the print head for the two black inks.
@dea3454
3 ай бұрын
sorry to bother you i got i quick question for you got the dx7 damper from aliexpress my question is from left to right i got bottom m top black seconf one cyan top empty bottom cause its clogg real bad then 3 damper top yellow bottom empty clogg also the last on the right are white white what setting for colors in acro rip should i use im confuse and not sure witch one to turn off
@rafalwaszkowiak6165
2 ай бұрын
Hey you have air bubbles in lines is this a problem ?
@dtfturkiye8254
2 жыл бұрын
Thank you very much for your videos for p600 printer conversion. but several different dx7 Dampers are sold. which type dx7 damper should we use
@IronDesigns813
2 жыл бұрын
I currently have the p800 CISS from nikko Dtg 2mm if I’m not mistaking
@hectorrojas5115
Жыл бұрын
Hi, how did you end up attaching or replacing the motor?
@IronDesigns813
Жыл бұрын
i cut all the extra bracket off and the black wire must be attached, i just layed the motor in the print head carrier it doesnt move.
@manoskamenakis2611
Жыл бұрын
Thanks for the video, i have a few questions 1. How hold down this dampers? 2.What is the size of the ink ciss tube? ( they are two sizes of the dx-7 dampers on the market ) 3. The white ink need shake how solve this? 4. you make clean circle?
@IronDesigns813
Жыл бұрын
1) popsicle stick which as of Jan 2023 I don't use popsicle stick it just stays 2)I used the p800 version ciss with damper set from nikkodtg 3) I just shake the tank every two days .. I print a lot daily so I don't really worry about shaking inks .. every printer with lines from carts to print head has ink separation in lines if you don't print every two days at most kzitem.info/news/bejne/r2qJnaKVoYthqH4
@stamparartestamparia9341
Жыл бұрын
Estas epson tem motorzinho porcima do carro impressao nao vi na sua a gente remover ele
@allenmayberry3009
Жыл бұрын
Hello will this work for p800 Epson and what about the air that get supplied to cartridges will that need to be capped off or will the air just stop after initiation
@rokYYs
7 ай бұрын
Have you tried this mod on p800 ?
@IronDesigns813
7 ай бұрын
the air will eventually come out no need to worry about it i never did
@IronDesigns813
7 ай бұрын
this mod was done using p800 ciss on a p600 so yes its possible
@thilaanmendis4771
7 ай бұрын
Do I need to keep the motor on top of the printhead if I’m using p600? I’m also using dx7 dampers as well on the p600 sure color
@IronDesigns813
6 ай бұрын
i put it next to it plugged in making sure it dont move back and fourth when print head carrier moves
@pauldavis7703
2 жыл бұрын
Sooo.... You're the keeper of the forbidden knowledge! 😆
@jamess2285
2 жыл бұрын
Great video. I already ordered my ciss.
@joss8282
2 жыл бұрын
If I turn my P600 into a DTF printer, and I have the ink tubes connected directly to the dampers, what settings do I need other than chipless? If you could teach me, it'll helps a lot.
@IronDesigns813
2 жыл бұрын
So you would set your carts from left to right standing in front of the printer. And in acro rip 10 you’ll set your channels from left to right as well to match. You can put white in lc LM and cymk as normal. (Either white in llk and lk or you can run fluro yellow and fluro magenta ) you’ll need to shut them on and off accordingly for fluorescent and non fluro printing.
I have a epson p800 that's i remove the printhead for flushing and after that they dont want to print the color correctly trow the original ink sistem...do you think that doing the same you do going to work?
@IronDesigns813
7 ай бұрын
it depends if you pushed fluid through in other words water fall, you may have busted seals, if you didnt did you clean capping station? if that isnt suctioning properly it wont really clean or suction inks to the head.
@IronDesigns813
7 ай бұрын
if the problem is in the ink lines then yes this should resolve
@thepitstop77
Жыл бұрын
My p600 print carriage is moving left and sticks ????
@IronDesigns813
Жыл бұрын
join my group facebook.com/groups/craftingwithirondesigns813 send me a video
@etog143
2 жыл бұрын
hi it's westbay here ... you can pull the wires from the dc motor so you dont have to put the original dampers back.
@thepitstop77
2 жыл бұрын
Which wire is this I’m not sure
@IronDesigns813
2 жыл бұрын
Yes please which ones?
@trapnerd1173
Жыл бұрын
Did anyone ever find out what he meant
@marceloStampColor
8 ай бұрын
Pode me ajudar? , fiz igual a vc a minha dtf e agora esta dando erro 0xd9 erro de seletor de tinta , o motor a De troca de tinta gira direto e da esse erro , consegue me ajudar?
@IronDesigns813
7 ай бұрын
send me pics on face book of how you have it set up , did you plug the motor in and place it in the print head carrier to the side?
@kbi4739
9 ай бұрын
Anyone know the orientation of the flat head cables? Cn1 goes in top slot by WiFi or the lower spot?
@IronDesigns813
7 ай бұрын
cn1 long side should be plugged on bottom of the two slots on the print head the cn1 label and metal prongs should face out not towards the print head the top cable has the prongs facing the print head and the blue strip visible outward. the short cn1 goes in the front slot of the print head carrier if standing facing front of the printer.
Пікірлер: 39