what can you tell me why the front engine after changing the hall sensor takes too much ampere code for the bottom engine
@jasminbuilder
7 ай бұрын
@@EVCustomscan you tell me whay my 1 motor after i change the hall sensors is taking to much ampers the 2 motor takes 1.5 ampers but 1 motor is taking 10 ampers
@garyfyvie9490
4 ай бұрын
I finally decided I must make my repairs, to start can you tell me best way to match an exisiting controller, I know how from the out side. But as you know buy one then open and see what was sent.😮 board I want has heavy traces - strips of conductive material to increase current flow and effectientcy. I have the fiido T1 cargo where can I find a good controller? thanks
@jfeliciano15
3 ай бұрын
Great instructional video. I noticed that some Fardrivers have a label for Cruise/Park function. Can you explain how park function is engaged and also how to switch PINS for different functions on the app.
@EVCustoms
3 ай бұрын
Hello friend.. have many half-made videos on my list and i don't have free time for fardriver short videos, it will take quite long time friend...
@ethanhunt1828
26 күн бұрын
Hii there,I have Park/Cruise button in right combination switch of my ev bike,It has 2 wires coming into the connector- Blue and Blue+White wire. 3 wires for 3 speed and one black(GND) wire.How do i activate Park/cruise mode button functionality,should i connect blue to Blue of Fardriver cruise wire.I am confused please help.
@Armandot6
7 ай бұрын
Awesome video! I would love to see a video of you tuning the Fardriver.
@alantierney1
Ай бұрын
What wire is for region?
@hectorvargas5628
3 ай бұрын
Hi friend, I tested the battery terminals on my fardriver (pos and neg) and there seems to be continuity, is it normal or is it bad?
@EVCustoms
3 ай бұрын
The continuity tha you see is thrue controller capacitor's.. it is new?
@hectorvargas5628
3 ай бұрын
@@EVCustoms Yes, is the first time that I tried to power it with 72v and the BMS of my battery cuts the current because it detects a short circuit.
@EVCustoms
3 ай бұрын
Your polarity is correct? if yes your MOSFETs must be shorted.. check resistance and continuity between Negative yellow , negative blue, negative green, and same with positive, there you can find your shorted mosfets
@hectorvargas5628
3 ай бұрын
@@EVCustoms with the controller open everything is covered in resin, I can't even see the board but I just tested the continuity on all the terminals, it gives me some values but it doesn't sound it just beeps for a while between the negative and positive poles, should I buy other one? 🥲
@EVCustoms
3 ай бұрын
If is beeping for some seconds its ok, is phase capacitors, it must be ok from mosfet side.. are you sure about your battery?
@vbnet2008net
6 ай бұрын
thank you
@pkbloodbender6914
7 ай бұрын
The entire connection run on 5 volts?
@EVCustoms
7 ай бұрын
Control system running on 5V
@Gkhanq
3 ай бұрын
Kalkarken zor kalkıyor, motor titriyor neden
@manicmods
7 ай бұрын
This was so well done! I was going to produce a similar video but now I will just point to yours 👍 Subd for more, I'm a new content creator and just dropped a video on an undocumented Fardriver/Kunray problem. You seem very knowledgeable on these kits, and would love your feedback if you had a moment!
@EVCustoms
7 ай бұрын
Hello mate.. nice channel by the way... i just seen your video about FarDriver issue.. ;)
Пікірлер: 25