This arms me with the knowledge to dig into my 1947 8N….great video, thank you
@todaywithbk
2 ай бұрын
Excellent video!!
@xpsgarage
2 ай бұрын
Thanks!
@jjay718
4 ай бұрын
Nice job. I love these 8N tractors.
@xpsgarage
3 ай бұрын
Thanks 👍
@BruceAvilla
7 күн бұрын
When you put the rubber packing into the throttle shaft hole, did you put a brass retainer cup into the shaft hole to keep the rubber packing in place? Didn't see you mention that. Great info on the governor, and your run through of the carb cleaning was excellent. Not really necessary to remove the three brass jets (economizer, idle, and main) as they can be buggered up easily, as you found out on the idle jet. Good to check for proper diameter hole size on each: Idle jet .032, economizer jet .046, and main jet .052). Well done!
@jerryf609
8 ай бұрын
Never knew much about the govenor. Now i know a little Thanks
@jarheadlife
Жыл бұрын
I wish your videos and KZitem were around 20 years ago when I had to do this to my 42 2n
@xpsgarage
Жыл бұрын
Youngsters today just don't realize how hard it used to be to get good how to information.
@cristobalvillalpando7451
Жыл бұрын
Great video, very helpful thank you
@warrenstuart3423
10 ай бұрын
Appreciate the video learned ALOT for my 9n I just bought
@xpsgarage
10 ай бұрын
No problem. I hope you enjoy the new tractor.
@badassbees3680
Жыл бұрын
Best damn video ever!49 8n
@keithwarkentin
Жыл бұрын
Excellent you should be a shop teacher that old girl is looking newer and newer 😀🇨🇦
@Levikrw
Жыл бұрын
New sub! I have a 39’ 9n. It is running like a turd and I just put a new carb on and can’t get it to keep running
@xpsgarage
Жыл бұрын
Did you check the ignition system? That was the first thing I had to fix on mine.
@Levikrw
Жыл бұрын
@@xpsgarage spent all morning taking apart and reassembling the carb. Needed a new battery as well, oops! Got her running but the idol and rev are not acting right. My Governor linkage is sloppy to say the least. I think a Governor rebuild is in my future
@philliphall5198
5 ай бұрын
Parts are so dam high now, I finally quit buying and rebuilding them because of the price 😢😢😢
@LifeLover17
10 ай бұрын
Great video Working on my 8N -- Tractor surging Installed new after market carb -- half the weight of the marvel ( will rebuild ). Removed governor, cleaned ( wished I watched video before --could have taken it apart -arms are loose and play in spring . Where do you get brass shim ? Re-installed governor -- still surging. Ordering new governor -- will rebuild old one when I have time this summer. Really helped me understand all components. Thanks
@xpsgarage
10 ай бұрын
The brass shims I used were old feeler gauges I have for motorcycle valve checking. I usually get them from McMaster-Carr.
@jameslester3861
11 ай бұрын
I have never seen a 8N with the breather on the left side. I bought a new proof meter and cable and the inner cable was too short and had to by a universal, we’ll see if that works.
@knuckle47
7 ай бұрын
My ‘47 8N is also a left side breather
@steveridling3947
Жыл бұрын
I have an 8n. I had to replace the carburetor and now it tries to die when go up hill, I did replace the fuel filter and readjusted the carb many times from factory to extreme with no luck. Any ideas? Thanks!
@xpsgarage
Жыл бұрын
Is the arm from the governor to the carb opening the throttle when you start to go up hill?
@alarry31
6 ай бұрын
Do you have a fitting size and thread for the oil line.
@xpsgarage
6 ай бұрын
The one going into the governor? It's a 1/4 Tube-1/8 NPT Inverted Flare Elbow
@duanebolen543
8 ай бұрын
I bought A2N 1946. And it ran good when I bought it. I left the guy use it for 2 weeks. Went back to pick it up and it backed fires. And it will not stay running. Do you have any ideas? What might be wrong?
@xpsgarage
7 ай бұрын
I'd make sure you have good fuel flow to the carb and would probably also drain the carb to make sure there is no water in it. After that check the spark plugs and ignition to make sure you have good fire.
@duanebolen543
7 ай бұрын
@xpsgarage I already did all that an cleaned carb I think it's the coil, on six volt
@duanebolen543
7 ай бұрын
Has new plugs
@xpsgarage
7 ай бұрын
@@duanebolen543 Have you checked all the wiring to and from the coil? Do you still have a resistor block in the power line to the coil? They have been known to go bad.
@stevehearn3734
9 ай бұрын
Ok, is there a governor adjustment????
@xpsgarage
9 ай бұрын
I don't think there is much adjustment to it. Make sure there isn't any slack in the spring and that the arm is not all sloppy. The adjustment is in the throttle linkage. Once you have the throttle set then the governor just moves the throttle to maintain RPM.
@susanvaughn741
11 ай бұрын
I bought a complete new governor for $112.00. On eBay.
@dirtydish6642
11 ай бұрын
If its brand new, likely its an overseas (India or China) model and you may be in for some heart ache with its performance. Another video I found said that they salvaged a brand new overseas model by tearing it open and properly shimming the shaft which they found wasn't shimmed for preload at all. Good luck.
@xpsgarage
11 ай бұрын
Have you tried it yet? Some of the aftermarket ones don't work very well.
@jameschainey2343
7 ай бұрын
If you are using 1/2 inch it's a 5/16 bolt 🔩 just so the people understand. 😊
@xpsgarage
7 ай бұрын
What did I do? Say it was a 1/2" bolt instead of saying it uses a 1/2" wrench?
Пікірлер: 39