Die beste Erklärung aller Zeiten👍👍👍👍👍👍👍👍👍👍👍👍👌👌👌👌👌👌
@AjusaAutomotive
4 жыл бұрын
Hallo! Danke für deinen Kommentar. 👍 facebook.com/AjusaSpain
@wolfgangk751
7 жыл бұрын
Very useful and detailed described! Top Work! Best HowTo I' ve seen so far.
@AjusaAutomotive
7 жыл бұрын
Hi! Thanks for your comment. You can find more information in our Facebook facebook.com/AjusaSpain/ and in your Twitter twitter.com/Ajusa_Spain. Best regards
@wolfgangk751
7 жыл бұрын
Ajusa Thanks, I just add your site at Facebook. Are you also present on Instagram?
@AjusaAutomotive
7 жыл бұрын
Yes! This is the link: instagram.com/ajusaspain/. Best Regards.
@rjshhooba9857
3 жыл бұрын
nice work, there is something you forgot to show, 22:14, there is a pipe coming out of the carter ventilation, what did you do with it?
@AjusaAutomotive
3 жыл бұрын
Hi! There are some gaskets that we did not show due to poor installation view to record it, but that does not indicate that we did not assemble the correct gasket. Sincerely 🖥️ facebook.com/AjusaSpain 📸 instagram.com/ajusa_automotive/
@rjshhooba9857
3 жыл бұрын
@@AjusaAutomotive okay, what does the pipe do?
@DNV970Raze
3 жыл бұрын
Hi, does this engine have a PCV valve or diaphram? Does it have any PCV system at all? I have been looking for ages but didn't find any info about it. My engine has very high oil consumption and I think part of it might because of it. Hope you can answer my question. Great video btw!😊
@AjusaAutomotive
2 жыл бұрын
Yes, your vehicle has pcv valve in the rear of the engine. Kind regards 🌐 www.ajusa.es 🖥️ facebook.com/AjusaSpain 📸 instagram.com/ajusa_automotive/
@DNV970Raze
2 жыл бұрын
@@AjusaAutomotive Is it located on the intake manifold? Connected to the secondary PCV line on the valve cover?
@AjusaAutomotive
2 жыл бұрын
@@DNV970Raze Exactly. Best regards
@Schumaher7305
2 жыл бұрын
Hi, what is the diference at 1.4 Z14XEL vs Z14XEP ?
@AjusaAutomotive
2 жыл бұрын
Hi! The main difference is the power output, but both install the same gaskets. Z14XEL: 55 kW (75 hp) a 5200 120 Nm a 3800 Z14XEP: 66 kW (90 hp) a 5600 125 Nm a 4000 Best regards
@blitzgameplay007
5 жыл бұрын
Thank you for an excellent video. :-) After applying Ajusil 14:05, how many hours should pass before starting the engine?
@AjusaAutomotive
5 жыл бұрын
Hi Blitz! Thanks for your comment! Our product reaches the total curing after 18 hours, so you must wait that time before starting the engine. Best Regards Follow us facebook.com/AjusaSpain
@sara78130
8 жыл бұрын
allways doing best job and best vids
@AjusaAutomotive
8 жыл бұрын
Thank you very much!! Best regards
@CroIntr00X
7 жыл бұрын
so professional, wish like more mechanics work same as you do...matching required screw angle values and Nm..just amazing
@AjusaAutomotive
7 жыл бұрын
Really thanks for your comment!!
@jagnandansingh7284
7 жыл бұрын
xuv Mahendra
@AjusaAutomotive
7 жыл бұрын
We do not understand your comment. Please , what is your question?
@jacitdm
2 жыл бұрын
8:10 🙆🤦
@Vladimir_Saf
5 жыл бұрын
Я восхищен! В России есть ваши представительства?
@AjusaAutomotive
5 жыл бұрын
Привет! Вы можете связаться с нашей делегацией в России здесь: 108803, Москва, п. Воскресенское, пос. Воскресенское, д. 66, а/я 1890 Тел. +7(499) 608-06-81 / +7(916) 060-07-24 Контакты: info@ajusa.ru www.ajusa.ru Приветствие
@MrAndrew199
7 жыл бұрын
masterpiece
@AjusaAutomotive
7 жыл бұрын
Thanks for your comment!
@marcelrbk7194
3 жыл бұрын
Salut . La ce cuplu ați strîns șuruburile de la întinzător ? Merci.
@AjusaAutomotive
3 жыл бұрын
Hi! 8Nm. Best regards 🖥️ facebook.com/AjusaSpain 📸 instagram.com/ajusa_automotive/
@carlitoscardona2425
4 жыл бұрын
why in the all videos that person not using any type of glue or silicone to sill the cover of blockhead, or is not necessary to use any glue in any surface ???? because I always use silicone to sill something
@AjusaAutomotive
4 жыл бұрын
Hi! We repair every engine following the OEM manufaturer instructions. Silicone sealant use is only recommended in some areas that are indicated in the original warehouse manual. Thanks for your comment and best regards.
@ukaszkarpik3476
7 жыл бұрын
What kind of liquid is applying betwen the camshaft and head 12:08 ? Can i apply standard 5W30 engine oil? Can you explaxin what happens between 19:10 to 20:02 ? After the block of the the timing system and crankshaft you installed the tool for registration of the camshaft position sensor disc. Then you tightened the both camshaft bolts by 1Kpm initially. After the registration tool and all blockades are removed, you tightened the bolts finally by 5Kpm. Then screws were tightened for 60 degrees angle. As we can see, the sensor disc is rotating in this step, but in the next step the position of sensor is correct. I see some discrepancy between these steps. Anyway, really good and detailed tutorial!
@AjusaAutomotive
7 жыл бұрын
Hi Lukask! Thank you for trusting AJUSA. We will answer your question shortly. Best Regards
@AjusaAutomotive
7 жыл бұрын
This liquid is mechanical assembly oil. Yes, you can apply standard engine oil. Between 19:10 and 20:02, we apply the torque and angular tightening to the camshaft bolts in the following sequence, 1kpm / 5kpm + 60 degrees. After that, we turn the crankshaft 2 turns and we put the synchronization tools to check the moment of the belt. You are right, keep in mind that sometimes it is necessary to record at a different time than the right assembly . You can find more information in our Facebook facebook.com/AjusaSpain/ and in your Twitter twitter.com/Ajusa_Spain. Best regards
@TheTrollSquad
6 жыл бұрын
what can i use instead of that tool in 3:57?
@AjusaAutomotive
6 жыл бұрын
Hello! In this case, we always recommend being used that valve steam installation tool, because it prevents possible damage on the head of the seal and will ensure a correct insert in the cylinder head. In the next link, you can find an example of this kit on internet: www.amazon.es/Timbertech-herramienta-retenes-v%C3%A1lvulas-adaptadores/dp/B011LD2Y5I. You can find more information about AJUSA in our Facebook: facebook.com/AjusaSpain and in our twitter: twitter.com/Ajusa_Spain. Best Regards
@user-hq1yn2ec7t
4 жыл бұрын
Здравствуйте помогите мне не найти Шатун на опель мерива 2008 1,4
@user-hq1yn2ec7t
4 жыл бұрын
Где можно купить Шатун на опель мерива 2008 1,4
@AjusaAutomotive
4 жыл бұрын
@@user-hq1yn2ec7t К сожалению, мы не производим моторные шатуны. поздравления
@gabrielemancuso2219
3 жыл бұрын
che senso ha questo video se non mettete il serraggio dei perni?
@AjusaAutomotive
3 жыл бұрын
Hi Gabriele! Per favore, puoi dirci quali viti abbiamo lasciato allentate? Un saluto Please, can you tell us which bolts we left loose? A greeting 🖥️ facebook.com/AjusaSpain 📸 instagram.com/ajusa_automotive/
@gabrielemancuso2219
3 жыл бұрын
@@AjusaAutomotive non intendevo dire che avete lasciato delle viti lente ,ma almeno dire la coppia di serraggio
@AjusaAutomotive
3 жыл бұрын
@@gabrielemancuso2219 Di che coppia hai bisogno? Dicci e te lo invieremo. Salut What torque do you need? Tell us and we will send it to you. A greeting
@mithatpushaka7143
2 жыл бұрын
po
@yo_yoyo_yo8294
4 жыл бұрын
kzitem.info/news/bejne/1oijzW2Ya5p0gG0 -YOU can tell me why it sound like this my engine? Thank’s
Пікірлер: 46