Thank you for watching my video. I hope see you again in my channel. God bless.
@Tringhieu
2 жыл бұрын
Thank you for sharing nice moments Chief!
@mozirichiefengineer7916
2 жыл бұрын
Thank you for watching. See you again. God bless.
@life-at-sea
10 ай бұрын
Great job indeed
@mozirichiefengineer7916
10 ай бұрын
thank you for watching my video. I hope that my video is helpful for your reference. See you again. God bless.
@najinkunnath6009
4 жыл бұрын
Good job...!!!! Very useful video. Expecting more videos in future.
@mozirichiefengineer7916
4 жыл бұрын
thank you for watching my video
@giri6996
3 жыл бұрын
thank u sir very nice video
@mozirichiefengineer7916
3 жыл бұрын
thank you for watching my video.
@overgame1857
4 жыл бұрын
잘 만들었네..굿~~~~~~
@mozirichiefengineer7916
4 жыл бұрын
이광연 thank you
@sakeovuadreu4984
2 жыл бұрын
nice job
@mozirichiefengineer7916
2 жыл бұрын
Thank you for watching my video. Bon voyage. God bless.
@sakeovuadreu4984
2 жыл бұрын
@@mozirichiefengineer7916 thankyou sir for all your overhaul videos..... all the best onboard... god bless
@shubhamkotiyal3708
3 жыл бұрын
thankyou guys
@mozirichiefengineer7916
2 жыл бұрын
Thank you for watching my video.
@JustaCuriousity
3 жыл бұрын
Hi, it will be great if you show how the gasket looks like, because im overhauling Yanmar 2T75L. With alternate sleeve, its higher than block 0.4mm, wondering if its okay. please advise, thank you. Great video!
@mozirichiefengineer7916
2 жыл бұрын
First of all, thank you for watching my video and I am sorry i don't have an experience of Yanmar 2T75L model. I recommend that check the length from block to liner prior to disassembly and check the length again after re-assembly. I think if the measurement is no difference or a little bit, probably there is no problem.
@polkpolkov1094
2 жыл бұрын
Many thanks ! Very good work ! Please tell me how much wear on the cylinder liner has to be in order to replace it? And how much will it be in operating hours? Thanks !
@mozirichiefengineer7916
2 жыл бұрын
I am so sorry you are waiting long time. i am onboard at present. Therefore i can’t answer at the time. i am sorry for it again. At the renewal time, the cylinder liner wear-down was 0.38~0.45 (limit 0.3mm) and total running hours 15,000 and almost 8 years since delivery. Normally, 3 sets of Dynamo Engine are installed on ship. We did dismantled No.1 D/E pistons according to PMS (every 8,000) and found a lot of cylinder wear-down. However, Cylinder liner spare was not enough. I supposed that the other D/E Cylinder condition is probably same condition . Anyhow i report the measurement and just assembled No.1 D/E piston at the time 2 months later we received 12 sets of cyl. liner and started replacement.
@polkpolkov1094
2 жыл бұрын
@@mozirichiefengineer7916 I am very grateful to you for your answer!
@sirota881
Жыл бұрын
Можно проще пойти берёшь таль 1.5 зацепляешь за приспособу и вытаскиваешь сразу без всяких ключей!!!
Пікірлер: 26