This is amazing! The thought process behind getting the perfect installation is incredible. I installed mine perfectly.
@ssgviper7147
Жыл бұрын
I've tried all kinds of screen protectors, film, plastic I've also tried UV cured glue from most likely knock off brands. This one by far is the best it covers the screen properly but it doesn't overdo the edges so that it doesn't have a clean crisp fit. this is clearly the leader in this screen protecting industry.
@dmj2_
6 ай бұрын
Excellent screen protector! The install was a success the first time around (now I have a spare screen protector) and the set up is well thought out. Best thing about the dome glass - it looks REALLY good. It looks way better than two other screen protectors I've tried, and one of them was more expensive than this one. My ONLY additional advice: My table is generally level, but apparently not level enough. At the step where you first let the adhesive pour out, prepare to adjust the leveling as my adhesive starting moving down the screen (slowly) from the start. This was a quick fix by propping up the phone with some paper, and then the rest of the install went as planned. If you're unsure whether your surface is perfectly level, prepare to adjust on the fly.
@WhitestoneDome
4 ай бұрын
Thank you for the tip! If you need any assist from us, hit me anytime. Have a good one, Buddy!
@CrazyDoug17
Жыл бұрын
Works wonders for me, i followed the exact tutorial on a table and it's brilliant! Finger scanner still works. I've turned up the touch sensitivity and re programmed my finger and it works well, even with a case!
@kaylagruce1047
8 ай бұрын
This is the only screen protector I will use anymore. Perfect install every time and it really does protect the screen very well.
@WreckedBrewery
Жыл бұрын
Worked really well on my s22 Ultra, and now on my s23 Ultra. Great job!
@abohsukampret
Жыл бұрын
Works flawlessly. I was afraid to do anything wrong the whole time but I'm very happy with the results. Here's to hoping it'll last long.
@supermech6329
Жыл бұрын
Best screen protector ever! Just installed today on my S23 Ultra - worked great! Way to go Whitestone!
@KitsFigs
Жыл бұрын
Just thought I'd drop by for others... I used the Whitestone Dome Glass on my S20 Ultra 3 years ago. It's gotten a lot of nicks and scratches and cracks over the years of course... But I just pulled the glass off for the first time in 3 years, and it's flawless underneath, 0 scratches, dings, cracks, etc on the original phone screen (after well over 1,000+ drops). The dome glass has done its job phenomenally and I will be happy to get it for the 23 Ultra next.
@emmanuelsimpson1751
11 ай бұрын
Have u tried removing from the s23 ultra? And was it gud?
@uTubeNoITube
8 ай бұрын
1,000+ drops??? You drop your phone literally every single day? WTF....
@edwincupely
8 ай бұрын
Absolutely. You can change it by the second year with the extra glass included, change the case or cover, and continue having a pristine cel.
@sharathpaka4198
6 ай бұрын
Was it easy to remove this screen protector? Or it's hard?
@arjundimazz
Ай бұрын
@@emmanuelsimpson1751 So I used this exact product for 1 year, Used two of them that came in the set, the first one lasted me 6 months and the other unfortunately let me down after 4 mohtns, I noticed my phone screen was cracked and assumed it was the screen protector. But to my horror when I was gonna replace the glass, my phone screen was cracked. Coseted me 350euros to fix this. Despite this incident I think this is a good product, it lasted me for so long with perfect instillation. I recently fixed my phone and baught the same dome glass, It's perfect.
@Gyppor
22 күн бұрын
You guys have created a great system for installing, very clever. I watched this a few times before doing it and my installation looks perfect. I had a bit of glue spill onto the buttons but the tape protected them. The protector fits just right in a Spigen Optic Armor case on my S23 ultra.
@vladimirrosu4932
8 ай бұрын
Bought it today, installed it myself on a S23 Ultra. This video was enough for me. The only variation that might exist in the installation is when you place the glass on the phone. If you make sure that bottom touches both plastic pins and the top is centered horizontally, you're fine.Ah, and the dust. Make sure you have a cap for your hair and you do this in a quiet place, without air that could get dust after you cleaned it from the phone. Really nice. I use it with a Spigen Tough Armor with no issues.
@FlimsyIndo
Жыл бұрын
I am very satisfied as well with how everything turned out. Thanks Dome
@HenningGu
Жыл бұрын
Worked pretty well and mine has absolutely no blemishes anywhere. 🤩
@liminalsunset
Жыл бұрын
If your table is not perfectly level, this won't work correctly. Have some little things around to shim it so the glue stays - it's quite liquid and can run off easily if you're not careful. It worked fine for me. Fingerprint scanner works fine, slightly worse than before but nothing significant. Overall happy with how the installation went.
@mikehong1500
18 күн бұрын
Really easy to put on and it works well. I've had one on my S23 Ultra for about 6 months and had to change it because I cracked the glass and it was driving me crazy. The first screen was on perfect until I accidentally lifted a corner of the glass when putting the phone in a case for the first time. Always intended to redo it with the second glass but didn't get around to it until the crack... Second screen looks good but somehow I ended up with two tiny air bubbles. They were big when I dropped the glass to the screen and I used the little plastic head thingy to try to push them out before using the light. Worked pretty well but still ended up with the two pin prick sized bubbles that just wouldn't budge. I'll probably wait until another crack before I get a new pack and try again.
@ebasguy
Жыл бұрын
In case some of you are having difficulties with the fingerprint... wait a few hours, it works on mine now!
@tseyang6079
Жыл бұрын
Thank you WhiteStone for the detailed video. I followed the directions and my glass is perfect.
@tseyang6079
3 ай бұрын
I dropped my phone on pavement, which caused some cracks on my screen protector. I removed it and installed again with the provided extra kit. It's perfect again 🎉
@idzerve
Ай бұрын
After throwing out one cheap product, this is perfect fit and works excellent.
@KazuyaYuza
Жыл бұрын
Thanks, worked well. The tutorial went a bit quick, but good thing it's possible to slow the video down ^^
@sleepy1171
Жыл бұрын
Ive bought my S22 ultra and Ive had it for 5 months now. And Ive had 4 Whitestone glass screen protectors for it since. I don't even drop my phone. I put my phone in a seperate pocket everytime so it's not rubbing against anything. And somehow the screen cracks. Everytime I get a new Whitestone screen protector, I try even harder to care for it, being as gentle as I can and somehow it still cracks. Here it's $89.00 for 1 glass screen protector so I've spent about $356 in total for these. I don't believe this a good product. I may as well just break my screen at this point and replace it. I guess you've made your money off me Whitestone, you win. I won't be buying anymore.
@_luckicharms
Жыл бұрын
To play devils advocate; I was quoted $350 to replace my s20 screen.
@user-vg7vl8iv9o
7 ай бұрын
Did you get off Amazon?
@sleepy1171
7 ай бұрын
@@user-vg7vl8iv9o just from the Asian mobile kiosk stores in the middle of the shopping mall.
@dswartze
7 ай бұрын
2nd phone (S22 Ultra & now S24 Ultra - flawless each time. Best screen protector!
@AlphaBravo860
4 ай бұрын
I'm so excited! 5am! Just got mine in the mail!
@cnnrdvd
7 ай бұрын
Perfecly works fine is easy to put
@BretMuckdogs
Жыл бұрын
Interesting that an absorption pad was added for the bottom of this year's design.
@jodeci888
Жыл бұрын
The added rubber weight is different as well
@_Lina_0203
Жыл бұрын
Perfect screen protector! Finger print and s pen work as without. The screen looks like there is no glass on it. With the installation must be carefull tho
@404-file-not-found
Жыл бұрын
Be careful. The weight step pulled my protector down via gravity and ruined it because I didn't notice til after the curing step
@charlescrowell6893
2 ай бұрын
Always nice to use decent quality screen protector. Is there a way to replace the coating as it starts to wear off.
@cherryblossom243
2 ай бұрын
Hello, I want to ask about the glue shelf life. Can a brand new glue expire or has a change in quality if it's only stored in a dry and clean place (inside the whitestone package)?
@cocosricos5541
Жыл бұрын
Did all this and fingerpribt scanner with thus foil failes a lot.
@Jose-Luis.Garnica-Sanchez
3 күн бұрын
What if the screen is cracked? Can I use the spare or will the glue cause issues?
@mulletbaby01
Жыл бұрын
I bought this product and both of the screens had marks on them on the outside and I am not talking about the 4 dots on the screen, they were cloudy on the front. I ended up returning the product back to Amazon. I was a bit disappointed spending that much on something to have it fail quality control. Oh well I guess I'll live with out the screen cover for now.
@WhereAmEye2187
Жыл бұрын
I totally F'd this up right around the part where we put the glass on. How do I remove it and clean it to start over?
@AMalas
Жыл бұрын
For future reference: just remove all the liquid with a tissue, clean the phone and the screen protector with alcohol after to make sure you remove all Loca
@carlosrios7088
Жыл бұрын
kzitem.info/news/bejne/w4lvyqiqrmNmgqA
@happytrails1963
Жыл бұрын
Thjanks for video very easy install. 3rd phone for a dome glass they are awesome
@DienekesShade
7 ай бұрын
Hello. I've just installed this screen protector on my Galaxy S24 Ultra. I found out that there are 8 tiny dots, placed symmetrically (two at the top, two at each side and two at the bottom). The second screen protector looks the same. Recently I installed Whitestone Dome screen protector at my wives' S23 Ultra and it was spotless. So, my question is, is it by design or did I buy faulty set?
@G8GTJav
7 ай бұрын
Quick easy instructions. Success.👍
@BluesFanUK_
7 ай бұрын
Was going to order off their website, reasonable sale for the protector at $32, except it costs just as much to ship to UK... £40-50 for a screen protector is insanity.
@BillTheScrub
Жыл бұрын
Do we let the middle of the adhesive drop to the middle line or do we only let it go down until the bottom of the adhesive touches the middle line? This video and your website have conflicting information
@benelhirmez4408
Жыл бұрын
You want the center of the adhesive circle align with the middle line. I'm speaking from experience.
@Kaiben9
Жыл бұрын
Late to reply, but for future reference, the website screenshot seems to be referencing an installation guide clear plastic bar - also mentioned in #3 step of "During the install" instructions. If I recall correctly, they used to include this guide bar in the kit. But for some reason it's not included in the box and not mentioned at all in the video. Also if you look closely in website screenshot, the frame is slightly different looking compared to what is in video - example being the center section with the arrows
@BillPappas
10 ай бұрын
Sould include 4 bottles of glue instead of 3.....the spread of the glue is better when you seperate the glue in two spots.....cause its almost impossible to put the glue exactly in the center... a little bit of centre will cause glue not to reach some spot respectively the direction of misalignment..and thats what happend to my first attempt...but its a good trick to sell more boxes....instead of having separate glue and glasses..
@vladimirrosu4932
8 ай бұрын
I installed mine on a horizontal table and I had really no issues with glue not spreading everywhere. If your working place is slightly tilted, then I can imagine this happening. Otherwise this should not be an issue (I guess)
@zarleymcalpine3131
Жыл бұрын
If you have to change screen protector,and use second one, how easy is protector to remove,does the liquid harden?
@randykeith1203
Жыл бұрын
One of mine had broke and saved my actual screen but removal was a pain in the butt my girlfriend tried and got it off but it shattered into multiple hard pieces to get off
@tseyang6079
3 ай бұрын
I used a credit card and slowly removed it from the corners. Be gentle so you don't nick the screen
@Priss933
9 ай бұрын
why not place the glue holder in the middle if you want us to tilt the phone to force the glue to the middle ?
@SMac86
8 ай бұрын
They probably don't want someone to slide it all down to the bottom and off the phone by starting in the middle
@stevecoates9979
7 ай бұрын
If you started it in the middle, it would be easier for the screen cover to touch the adhesive before you were really ready for it to, and make a mess. At the end, since it's lifted up highest at that point, there's more room underneath the cover and so more margin for process error.
@Vamplord111
10 ай бұрын
To bad my anxiety will probably cause me to mess this up thus I won't make this purchase for my Samsung s23 I have coming even though I really want to! I don't even have the nerve to install a regular screen protector on my own lol so I will probably just buy what ever screen protector from my carrier and have them install it and get samsung care. It's been a while since I've been this disappointed in my self lol life goes on. Great video!
@james_msuk
6 ай бұрын
Did mine but got glue absolutely everywhere (somehow), have tiny couple of airbubbles right at the bottom of the phone, i'll ignore it though, far too much of a faff to get it on and I used all the wipes.
@edwincupely
8 ай бұрын
Have used it before on my S9, and continue been pleased on my new S23. However, don't understand the logic for the piece of rubber.
@ebasguy
Жыл бұрын
Mine looks great! Thanks guys!!!!
@Ceritakelam14
Жыл бұрын
bagaimana dengan lubang spiker, saya takut pasang, padahal sudah saya beli 🥲🥲
@nnnickkk
Жыл бұрын
Remember to remove/unregister your fingerprints *BEFORE* starting this installation.
@ssgviper7147
Жыл бұрын
You can get in with your pin and delete the old ones and re-registered.
@vladimirrosu4932
8 ай бұрын
Agree with the other reply. There is no need to do this process before.
@seppwurzel8055
Жыл бұрын
Leicht zu installieren, aber Fingerabdrucksensor funktioniert nicht mehr. Auch nach 2 Tagen nicht. Auch eine re-installation des Fingerabdrucksensor funktioniert nicht. S-Pan funktioniert super. Werde es noch einmal mit einem schwereren Gewicht auf dem Fingerabdrucksensor versuchen.
@MrWoytek007
Жыл бұрын
I installed 3 glasses and both of them break after a few weeks without any reason. I used domeglass with my note9 and s9+ and stiil fine.
@bilalayyad1643
Ай бұрын
Do you ship to Saudi Arabia?
@JG-oj9jz
Жыл бұрын
Is this case friendly with the otterbox defender pro? Don't say yes just to say yes
@jenotization
Жыл бұрын
Did you find out
@JG-oj9jz
Жыл бұрын
@@jenotization yes fits perfect with the case
@jenotization
Жыл бұрын
@@JG-oj9jz thank you so much
@ebasguy
Жыл бұрын
50 comments already... That's at least 60k already
@Moe395
Жыл бұрын
Best video yet on this install!
@rkmk7382
Жыл бұрын
Which case can i use with it ????😢
@zakthanasis9901
10 ай бұрын
Is it working with uag case?
@mcsavage1587
Жыл бұрын
How can I remove a single small droplet of glue from the ear speaker after installing?
@oxoConstantinEoxo
10 ай бұрын
Needle ?
@mcsavage1587
10 ай бұрын
@@oxoConstantinEoxoplease don't ever use needles on speakers haha from experience I ask you to please never do it. Also a post it paper solved the issue, the glue came out seamlessly
@Keif_Stoned
9 ай бұрын
alcohol
@Storm_x
Жыл бұрын
Does using this void samsung warranty?
@HenningGu
Жыл бұрын
Nope.
@onesteeltank
Жыл бұрын
Why would putting on a screen protector void a warranty
@bilalalalami4800
10 ай бұрын
i did it i installed it its amazing
@Tonio_onair
8 ай бұрын
for how much you charge for these screen protector. You could at least put this video in 4k
@niclaslindvall3095
Жыл бұрын
Does this fit the 23 ultra with dbrand grip case?
@nicolasmendez2287
Жыл бұрын
I am at the same point as you. I have a Dbrand grip case and have this glass, I'm going to try it out and get back to you
@nicolasmendez2287
Жыл бұрын
Can confirm, fits very well with dbrand grip case for the s23 ultra
@pavlosky8445
11 ай бұрын
Why glass unglue after two days ?
@oxoConstantinEoxo
10 ай бұрын
Cause you didnt used UV lamp enough. And nów its too late.
@Noire.Soleil
10 ай бұрын
Didn't work for me, even after following the steps. The very top of the screen wouldn't glue down. The idea is great though, just sad my money's gone.
@upadhyaypulkit10
Жыл бұрын
@Whitestone Dome I want to buy this in India, please help 😅
@WTfakinezaGaming
9 ай бұрын
I have a tiny small bubble after the installation, anyone experience it and how to fix it? TIA
@user-ph6vw5su7d
5 ай бұрын
Press down on it and like rub over it a few times with pressure, it will go away
@imranrasheed7447
8 ай бұрын
Very difficult to install
@josef.m.graham9453
Жыл бұрын
Please send me your Tempered Glass WHITESTONE S23 Ultra. It is not sold in my country Please.. =(
@SomethingMobile
Жыл бұрын
What does rubber type mean?
@KazuyaYuza
Жыл бұрын
Pretty positive they mean that square block at 2:39 as that's made out of rubber
@insanebmxthomas
Жыл бұрын
yeah that probably went lost in translation, pretty sure they're overseas. i remember when their company boomed, i believe it was during the Galaxy S8 age... Everything was typed in 'overseas' characters. Not sure which language lmao
@andrew83654
Жыл бұрын
Very bad design. Plastic warped. Glue does not spread equally especially in the bottom level
@darryl_mitchell
Жыл бұрын
I had the exact problem with mine too. Used both screen protectors and the same result. Almost like there wasn't enough liquid in each bottle. I've used these screen protectors before and have never had these issues. Oh well the whole lots in the bin now and that will be the last time I will use this product
@brian8319
Жыл бұрын
I think its from the surface not being perfectly level. I almost had this problem but tilted it around to fill in the missing spaces and it came out great
@rogerp.4489
9 ай бұрын
Shit was not level an just seeped through the sides 😅
@vaporware666
8 ай бұрын
I've done two with zero issues
@dswartze
7 ай бұрын
2nd phone (S22 Ultra & now S24 Ultra - flawless each time. Best screen protector!
@eXiiFTW
Жыл бұрын
Pixel 7 Pro worked like a charm, but this s23 ultra was a nightmare... last time that I bought Dome Glas
@mitchryan5468
Жыл бұрын
Might be silly question but what us the rubber for?
@UlvarinLind
Жыл бұрын
to force liquid to go to the edge of the bottom part of the screen i guess. without it it would not go even close to it, with it it took me like ~60-80s of pressure instead of 30s they said for it to reach edge. this is so stressing to do XD. doing it for every samsung since s9+ i had. now my s23 ultra is safe and perfect.
@mitchryan5468
Жыл бұрын
@@UlvarinLind ah ok
@paramountx
Жыл бұрын
I thought it was for the finger print
@mitchryan5468
Жыл бұрын
@@paramountx yea that's what I thought but not sure why I can't do thr method I've used for my s10 plus which is cure it for 15 top and bottom then press hard om scanner area
@benelhirmez4408
Жыл бұрын
It's to make sure the protector is making good contact where that fingerprint sensor is. You can just push it down with your finger after the 100s. That's what I did for my old phone.
@TheBollockz
Жыл бұрын
LOL but why....
@carlosrios7088
Жыл бұрын
even with the speaker cover sticker, some liquid got in my speaker and now it sounds bad. i flushed it with warm water, and i have my speaker face down with some music playing to hopefully get all the liquid out. but what do you guys recommend to do if this happens?
@MrRyanMcCall
Жыл бұрын
Did you make sure to make the speaker sticker completely flush and pressed down firm?
@rammium
Жыл бұрын
I completely forgot about the top speaker sticker cover so a lot of glue got into there. I used a razor blade to gently pry it out and it worked perfectly.
@Keif_Stoned
9 ай бұрын
Should have used isopropyl alcohol instead of water
@cdsmit27
Жыл бұрын
Does this work with the otterbox defender case?
@m.109
Жыл бұрын
Yes
@hubertbabula3735
10 ай бұрын
Speaker sticker is badly designed, glue is getting through, I almost damaged my phone
@MaxximumRage
Жыл бұрын
The one that Whitestone had for the S21 ultra was better. The "new" method reminds me of the method that gave me bubbles on my Note 9. Looks like I'll be skipping this brand.
@kentcm20
10 ай бұрын
Second install still got bubbles . Worst product ever made
@stevehan3809
Жыл бұрын
Very easy install
@ChristyanneMelendez
7 ай бұрын
Installation was a DISASTER! Despite using a level to ensure the surface was flat, the adhesive ran absolutely everywhere. I tried multiple times and nothing worked. The adhesive coated my phone and the two tables I tried to install this on. This was a brand new Samsung S23 Ultra. Not only that, the JIG spontaneously broke while I was using it, which caused my phone to suddenly drop and even more adhesive to spill. What an absolute mess! I do not recommend this product. I am shocked to read how many people were so successful with this installation. I watched the video multiple times (which I found not through the link provided on the very basic instructions, but through a KZitem search). I had no idea how runny the adhesive would be and how difficult it would be to work with. More information should be provided by the Whitestone Dome.
@davidexerrion28
7 ай бұрын
I have a same issue. Then I tried using card (credit card or another card) to force the adhesive spread correctly. It's worked for me.
@loterstoun7375
Жыл бұрын
Видимо только у меня руки из жопы😂 Теперь жалею что пожалел денег на установку🙈
@Гуканзполонини
Жыл бұрын
Что случилось ? Пузыри , затекла жидкость внутрь ?
@tony4love97
Жыл бұрын
you guys should find a way to sell these in india!
@steevstv3110
11 ай бұрын
The touch feeling is great, but the screen protector is very easy to be scrached and easy to be broken from short falls, I have repalced the second pack within less than two weeks, and the second one had a minimal broke on the edge just from very short drop after one day only..!! I'm kind disappointed, what I want to say at the end to whitestone: please focus on your main product quality over the installation perfection overall as consumers we're paying for the screen protector itself, not for the installation experience.
@vladimirrosu4932
8 ай бұрын
With or without case? And if with case, what model?
@poundsy7598
Жыл бұрын
Overpriced product with terrible customer service... I bought one for my galaxy s10+ the screen broke after 1 month, and was ignored by Whitestone dome customer service, when asking for a replacement under guarantee... for that reason would never buy again and wouldn't recommend
@black.bird.
Жыл бұрын
WTF I have installed many many glass protectors & this is my first time seeing this complicated process!! complicated doesn't always mean better. Worth the time & money? anyone tried with s-pen, fingerprint ?? color accuracy, cleaness ?
@josephkrieg5240
Жыл бұрын
I know you posted this a month ago but I thought I’d reply anyway in case you were still considering this glass protector. I’ve used these since my Note 8 and I have never had any trouble with the installation. It may look like a complex process but it’s straightforward and easy. Are they worth it? In my estimation yes, I’ve never had to put a second one on a phone and I typically keep my phone 3-4 years before upgrading. Phones have been dropped on hard surfaces many times and the Dome glass has chipped around the corners and I once had a crack across the glass that was only visible when the screen was dark. When I removed the Dome glass on both phones in the past, the phone screens were in pristine condition. So very good value for money. I use my s-pen often and have never had issues and the fingerprint scanner works with no problems. I just updated to the S23 Ultra and installed the Dome glass on it this morning and didn’t have any issues. I also use OtterBox Defender cases and haven’t had any problems with the screen protector coming off around the edges. Other people have had that issue but I never have.
@ahiqtidar
Жыл бұрын
@@josephkrieg5240 Hi, I have few stupid questions as they might appear to you. A) Does this adhesive cause any damage to the phone b) Does UV light impacts the phone screen or over curing (for beginners) might cause some problem to screen? c) Should I turn off my 23 while installing it?
@Car0111e
Жыл бұрын
This was horrid and way too fast. Unnecessarily stressful
@KazuyaYuza
Жыл бұрын
Just slow down the video and it's fine. Or pause in between
@dinopro2710
7 ай бұрын
Horrible design, had to use 2 of the liquids because one wasn't enough for the screen and if the water level of the surface is slightly tilted ur fkd
@shoganai2545
7 ай бұрын
Well duh, they said do it on a leveled surface
@dinopro2710
7 ай бұрын
@@shoganai2545 exactly why it's a terrible design
@j-rivs7174
4 ай бұрын
Its not their fault that you have the mental capacity of an expired baked potato and cant follow simple instructions.
Пікірлер: 150