Several people have commented saying I used the Torque Wrench wrong. They are applying rules without understanding the reasoning for the rule. The M16/M4 - 23&P Manual shows (With Pictures) the USGI Adapter being used inline with a Torque Wrench. Why is this when the experts claim it's wrong? It's because the torque values listed in the 23&P Manual (38-42 FT#) take that into account. When the USGI Adaptor is being used inline, the leverage it creates is part of the formula. The USGI Adaptors over the past 60 years have the same amount of distance between the torque wrench keyway and the centerline of the tools workpiece. I know because I own them all and have and tested them. Inline vs 90 degree value is less than 3 ft# for the USGI Adaptor and for this particular Tool and application. Notice how I set the wrench to the middle value (38-42 ft#)? My Torque Wrench was just calibrated and is accurate to -3%. That specific torque value was also important because in the past the castle nut was tightened with fixtures that didn't lock the receiver extension and lower into a solid fixture. Too much torque would cause the receiver extension to rip past it's keyway and cause clocking and damage to the tube. With better fixtures (as shown in this video) a higher torque value will not allow damage because the receiver extension and lower are in forced alignment.
@bidenisatraitor7633
11 ай бұрын
I don't give a damn what they say. I trust you before I trust them. Period!
@Doomer17018
11 ай бұрын
lol people love to point out what they think is an error because it makes them feel smart.
@ShawnD1027
11 ай бұрын
@@Doomer17018, for some folks, probably. For others, it's because stopping perpetuation of bad/damaging techniques is important (YES, I fully understand is NOT the case here).
@BlueCollarBachelor
11 ай бұрын
They'd really hate when I stick a castle nut wrench on there and wack it with a hammer.
@NuYo-
11 ай бұрын
G you don’t have to explain yourself to no one
@MyCCW
11 ай бұрын
My day is made...as enginerdial as many of us are, I'm surprised no one has come out with a staking jig up until now. Yes, I know it's a simple process with a punch, but I know it's taken me a few castle nuts to get good stakes "most" of the time. Most of us aren't staking castle nuts day in and day out so this jig looks like a great way to get good stakes. Kudos to your student for creating something that truly solves a problem.
@chipsramek3868
11 ай бұрын
@MyCCW ... I think it's Groovy that You still use Kudos.
@thatarguy
11 ай бұрын
The green jig everyone is asking about is the TechCo AR15 Receiver Extension Tube Jig. Y'all are welcome.
@TheSplitLicker83
Ай бұрын
Not all heroes wear capes
@TheSplitLicker83
Ай бұрын
Holy flamin' shitballs that fuckin' thing's pricey.....
@Wonderkidd863
11 ай бұрын
The alignment jig is the best part. Perhaps the developer will make one that aligns to milspec castle nuts at some point. Excellent product for those planning several new builds, but tough for existing. I actually prefer the non auto punch staking tool as well for whatever reason…so a single jig would be an excellent add to the bench 👍🇺🇸
@johngalt176
11 ай бұрын
I believe you can adjust the tension spring on the center punch to increase the striking force. Righty tighty. Lefty loosey. At least you can on my starrett auto punch.
@printingwithpeek4897
11 ай бұрын
The Starrett auto punch is an amazing punch. Definitely the best one out there, especially with the materials they're using.
@goinhot9133
11 ай бұрын
@@printingwithpeek4897I have the starrett auto punch, never noticed that feature
@printingwithpeek4897
11 ай бұрын
@@goinhot9133 Hey, it's never too late to learn@
@joelatkinson2080
11 ай бұрын
Just an idea for a future video. I'd love to see you do an evaluation of Anderson's RF85 treatment and how it compares to other friction reducing treatments and coatings. Love the channel and thanks for all the content you put out.
@printingwithpeek4897
11 ай бұрын
This is exactly the type of thing that makes homebuilds better. Sure, most people won't have machining capabilities but if you get parts from reputable manufacturers and you gauge them, you can have a rifle set up that meets and exceeds milspec. There is no reason, not to do this. I will definitely be adding this tool to my line up.
@lkazanov
8 ай бұрын
Very cool, the requirement for a proprietary castle nut is a bit of a turn-off. It is basically a locating punch jig. But kudos to them. The use of the Geissele receiver extension holder makes this task very simple.
@misterphuzz
11 ай бұрын
I like little inventions like this. My only recommendation, for version two of their product, is to angle it just a little bit, just a wee little bit, so that it puts a little bit more focus on moving material in the direction of the notch. Other than that, I like the idea.
@birdsoup777
11 ай бұрын
Awesome Channel. Appercaite your talent and your commitment to learn it
@mrsillyname
11 ай бұрын
Get this man to 100k!
@Pyle81
11 ай бұрын
Sweet little kit, Something ill definitely be adding to my Armour's Bench tool box. Thanks for showcasing this unique tool.
@thelastlatchkeykid8466
11 ай бұрын
I can watch these videos all day.
@michiganmafiamx5543
Ай бұрын
Thanks Chad, another great video. A couple firsts for me here, contemplating a drunk woodpecker’s actions was not one I expected to hear, but it was a well executed analogy. Kudos to drunk woodpeckers and great analogies..
@clint2211
11 ай бұрын
Awhile back I purchased a complete lower from Palmetto State Armory. It was suppose to be a non blem item but it turned out to be a blem item and a bad blem at that. It also turned out that the staking of the castle nut was horrible. With this armorer's kit I feel comfortable fixing the issue myself. Chad, I can't thank you enough for showcasing this unique item. Kudos to the individual for offering this and making life as a builder that much easier.
@kennyfinley8613
2 ай бұрын
Excellent tool and video. Only comment would be to use the wrench at 90 deg from the extension so you don't increase torque being applied from the extra length.
@BreezyBeary
6 ай бұрын
That tool is amazing and you are an exceptional armorer. Subscribed! I have assembled 20+ ARs and your attention to detail is top notch and I learned from you already! Thank you.
@matthewbeaver5026
11 ай бұрын
I understand that they would like for us to purchase their castle nuts. Though for us poors it'd be nice if they would make a jig for a mil spec nut.
@frozennorth3426
11 ай бұрын
I like the variant on the Fallen logo. More firearms reference back to the skateboard world :) Always good to see.
@mrshort2379
11 ай бұрын
Awesome castle nut staking kit, awesome design: However I dont want to come off like a troll, but I would have to iterate, that it is not worth the $85. price tag being asked, especially for a proprietary castle but and jig, and those of us that are not staking a daily multitude of castle nuts, you could most likely piece together that whole kit except the jig, for the price of the jig. Just saying
@NoWr2Run
10 ай бұрын
AGREED.
@TheWarriorSolution
11 ай бұрын
What a cool design! Awesome idea and perfectly executed for home builders. Well done Echo Zulu.
@nickadkins7765
11 ай бұрын
Tango Uniform is the name of the company. Echo Zulu refers to the name of the kit.
@tdjohnsky
4 ай бұрын
“Drunk woodpecker “ 😂
@bamzilla.
2 ай бұрын
Damn....just found this vid. Out of stock. I NEED! :D
@knewsome69
11 ай бұрын
Drunken woodpecker…so you HAVE seen my staking skills!😂
@mikedj420
8 ай бұрын
That bottle of sriracha is a must have for every serious armorer.
@digitalshooter2905
11 ай бұрын
The only bad part of this jig in my opinion is it's a proprietary tool. Should've just designed it to work with milspec castle nuts. Then maybe he could've designed a different castle nut that works with it and sold that as well if he wanted to.
@Radvous
6 ай бұрын
I bought the same spring loaded punch on Amazon a few years back, works amazing as a staking tool.
@BAdventures
10 ай бұрын
Good quick demo and review. Please review the Forward Controls CN5F Extended Castle Nut. More thread engagement and coverage. Is it stronger and any better than mil-spec?
@DickLickBiden-zy3nf
11 ай бұрын
Lol without reading instructions. Many may not enjoy your sense of humor and even more likely don't even catch most of it. I for one appreciate and enjoy it.
@philbaker29
2 ай бұрын
Not gonna lie, I'm in the "non-staking" group. But this is a handy tool.
@cjanquart
10 ай бұрын
That's a great jig; my first build went well but using a Starett punch I wasn't able to get it perfect, but at least I didn't bubba-gonsmif it (like nsz85). This is perfect for alignment then following up as you did at an angle without the jig. Agreed; would most definitely like to see a version that would work with milspec castle nuts.
@gregphillips9670
11 ай бұрын
I recently purchased a non AR related item and included in the package was one of the castle nut stickers. Naturally I checked out their website. I haven't bought a kit yet but will in the near future.
@johnknouse8846
11 ай бұрын
Could have used that several years ago when I was butchering my staking job!! Great video as usual.
@steveninaz9576
11 ай бұрын
Thank you Sir
@Maine307
11 ай бұрын
great tool!! BUT, lets also talk about that AWESOME greenish receiver holder!!! WOW !!! OMG!
@TheGalliaComata
11 ай бұрын
Nifty. I like that wrench head. At the very least nice fast way to make a couple centered marks. Thanks
@steveninaz9576
11 ай бұрын
Just ordered one. Great item
@scott2228
8 ай бұрын
That wrench looks like it will give FCDs a run for its $. If I didn’t have it I’d pick this kit up for sure.
@justlookingaround
9 ай бұрын
Looks like a great tool and definitely looks professional.
@Toolness1
7 ай бұрын
Very cool. Some of mine are ugly but they hold. I did order one of the spring loaded ones you pull back and let go to use on my next one, that'll help me a lot. I'll use a push-down one like this for my starting divot and then switch to the other for some more oomph.
@107gamma
5 ай бұрын
I got my tango staking set now. Thank you.
@markannadale7533
11 ай бұрын
Who makes the fixture that the lower and receiver extension was places in? That is very nice.
@Mr_Clean
11 ай бұрын
Techco. Ncstar makes one, botach makes one and G$$$$$ makes one
@BrassAngels
11 ай бұрын
Groovy little tool! Glad someone cam3 up with it cause I thoroughly enjoy tools that make my efforts easier & make my end result better. Cheers & Thank you! #SOTAR #SOLGW #ARJunkie
@NateDizity1420
8 ай бұрын
Good video. Just picked up the starter kit on Brownells. Nut Wrench would've been nice to have but trying to keep costs down.
@AR-ud1dp
11 ай бұрын
Hi, love your videos however why not just use the pws ratchet lock! It’s easy and awesome at the same time! Takes under a minute to install!
@SchooloftheAmericanRifle
11 ай бұрын
Because I have a negative opinion of them.
@AR-ud1dp
11 ай бұрын
@@SchooloftheAmericanRifleso I have learned a lot from your videos! More than I could once imagine that one day I’ll know so much about ar15’s. Please elaborate on what kinda problem or problems you are referring to?I have them in all my ar’s that I’ve built. 2 of them in particular have been run hard and somewhat abused. Never had a problem with them!
@akmarksman
11 ай бұрын
That is a neat product. Not a bad price for the Armorer's kit.
@silentstryker1590
9 ай бұрын
That's nice! Thank you for another upload.
@dangerdoberman
11 ай бұрын
Whoa. That's really great.
@Sam-et3bv
7 ай бұрын
Awesome. Very awesome.
@William-Bill-Munny
4 ай бұрын
LOL the Bob Ross of gunsmiths
@V8SKULLS
7 ай бұрын
Beautiful video, thanks for sharing, could you tell me you wonderful vise jig, the green one, that holds everything in line, I want to purchase one. Thank you very much
@Larrymoecurley
11 ай бұрын
You must be a great teacher!!
@samvittoria9692
11 ай бұрын
That is awesome.
@Whizzo333
7 ай бұрын
Actually the starter kit does have tool inside, small punch....🇺🇸✊
@justlookingaround
9 ай бұрын
And know we know, and knowing is half the battle, GI Joe.
@JamesBond-ut5iv
11 ай бұрын
It's an interesting one. I've gotten good at staking but this would have helped during the learning process. I've got some ugly ones for sure.
@pkake1319
11 ай бұрын
My stakes work. But aren't pretty, I would have bought this as a matter of pride in my own work.
@Auggie_93
11 ай бұрын
Didn't know you were based out of Maryland. Might have to give you folks a visit
@j_flo
11 ай бұрын
Thanks for the reco. I saw your ratcheting castle but video and I’m rethinking that method. 🇺🇸🦅2A
@5shotsr611
9 ай бұрын
Fantastic idea thanks for sharing!!
@bfonfield1534
11 ай бұрын
We need a hug for our FCD castle nuts sir.
@michaelfrangoudakis823
5 ай бұрын
That’s a nice tool.
@rux2213
4 ай бұрын
laughing at the "drunk woodpecker" comment!
@ryanthomas2374
11 ай бұрын
buying... for sure
@ravenovatechnologies6554
11 ай бұрын
Very cool tool, very good tutorial. But i do have a question. Have you ever seen issues from a badly staked buffer extention tube? To me it seems like even single stake is more than enough to hold it for a lifetime of abuse. Maybe i have rose colored glasses on, but ive never had a single issue with a castle nut backing off. Perhaps im just staking properly...
@frozennorth3426
11 ай бұрын
The receiver extension tube doesn’t need to be staked, only the castle nut that generates axial pressure between it and the lower (via the endplate which acts as a spacer between the two). Castle nut staking is a plastic deformation of the endplate metal that fixes the endplate’s rotation relative to the castle nut. (and the endplate in turn already has its rotation mechanically fixed relative to the lower) The expectable forces that could rotate the castle nut relative to the endplate are at worst what we would colloquially call “jiggling”. That’s it. Literally all we’re trying to do is control jiggling. We’re just doing so on a machine that’s pretty good at jiggling things. The only function of staking is to offer a degree of mechanical obstruction to Jiggling Rotation that is: - greater than our arbitrary thread friction and/or adhesive can provide - less than would require irreversible welding So, staking merely introduces a mechanical barrier to rotation (forming a plasticly formed de facto lug) that a little jiggling won’t overcome even when adhesives and friction from axial thread pressure have failed to attest the jiggling. That is to say, as something that actually changes the Shape of (plasticly deforms) metal objects, castle nut staking doesn’t really have to accomplish much. Picture a glass mason jar with a notch in it that you can hammer a bit of the rim of the lid into. You can shake that jar as hard as you want forever, but you if you’ve hammered a bit of the lid’s edge into that notch, no matter what thread friction and adhesive you overcome with shaking, that lid is never gonna rotate relative to the glass, because it’s floating in between the sides of that notch. It offers rotational resistance, but not in a fight against any rotational force, only against jiggling. A minor torsional effort with a wrench can break a castle nut stake like it’s nothing, and that’s the way it should be, because it’s meant to be a small and reversible thing resisting far Smaller stresses. In fact that’s the reason we call so much attention to castle nut staking: because it accomplishes something so mechanically Minor that most people don’t even imagine it’s worth doing.
@In-Midnight-Clad
11 ай бұрын
As long as the staking has moved enough material into the staking notch, it'll serve its purpose. Functionally, it doesn't matter how ugly it is, but Chad's a professional and cares about how his work looks. Understandably so.
@dalesmth1
11 ай бұрын
In my twenty years of building Ars, I’ve never staked a castle nut. Nor had one come loose.
@SchooloftheAmericanRifle
11 ай бұрын
Doing something wrong for 20 years isn't a good thing.
@JCunningham21
11 ай бұрын
How many Carbine classes has it made it through?
@dalesmth1
11 ай бұрын
@@JCunningham21 3,000 rounds and counting.
@mrpibb7781
11 ай бұрын
My two builds i "cheated" and used PWS ratcheting castlenuts. No staking required. This thing may warrant a looksie though
@DB2A7
11 ай бұрын
Fancy
@Cameron-bk5gk
3 ай бұрын
Shouldn't the castle nut wrench be 90 degrees from the torque wrench handle to achieve proper torque value? I always thought having it at any other angle would cause an incorrect reading.
@ForceRecon112
8 ай бұрын
If you're applying appropriate torque, something like vibratite is not necessary, correct?
@DerWaidmann_
11 ай бұрын
What is your opinion on the PWS ratcheting castle nut/endplate system?
@tonyc223
11 ай бұрын
I have 3 on lowers. I like them,never came loose. Thousands of rounds.
@bidenisatraitor7633
11 ай бұрын
I like this method better..just an opinion...stick to basics
@printingwithpeek4897
11 ай бұрын
The end plate is not truly ratcheting and does shear if torqued the wrong way. If you want that style of system, the better option is the Fortis K2.
@Shootsmith
11 ай бұрын
Love mine, switched over
@SchooloftheAmericanRifle
11 ай бұрын
Seen many come loose, especially if they are reused. The tooth wears flat.
@boinger1988
11 ай бұрын
very slick!
@allens9573
9 ай бұрын
The forever staking
@JadedGLORY2689
10 ай бұрын
Haha "We'll do it live. We'll do it F***ING LIVE!!!!!
@bayoucity1
11 ай бұрын
"I don't want to cut into the instructions." *Proceeds to tear the instructions to confetti.
@musician445
9 ай бұрын
"Oh yeah look at that staking". haha I love it man, i was saying the same thing to myself. Thats one of those moments where my girlfriend would have turned to me and said "NNEEEEEERRRD". XD
@jamesbullock3259
2 ай бұрын
Very Kool
@M14Shooter
11 ай бұрын
Great solution!
@vinceburris2538
11 ай бұрын
Could have used one of those a while back.
@sraldiris
11 ай бұрын
I need that!
@doejohn8674
11 ай бұрын
Very cool tool!
@Radvous
6 ай бұрын
Aren't crows feet technically supposed to be 90 degrees perpendicular? I know it really doesn't matter with such a short crows foot here, or if there's just a few more ft lbs on the castle nut on an AR.
@nickadams2951
10 ай бұрын
Does this work with a standard castle nut
@nuclear-salmon
11 ай бұрын
Hmm, someone should make a 3D-printable version of this tool
@charlesgillette2925
11 ай бұрын
Great idea.
@DET_C0RD
11 ай бұрын
What if I didn’t grease the threads before I put my nude buffer tube in?
@Whizzo333
7 ай бұрын
Probably be dead soon......
@Akinius
10 ай бұрын
Nice! I don’t currently have any builds planned, but I’m ordering one of these for my next project, whenever it is. Question, though… where do you get that aeroshell grease in that handy container with a brush built into the lid? I’m used to little tubs and having to use an external brush or something that dries out or gets lost between uses… Thanks!
@davelogan77
6 ай бұрын
Sweet.
@drewbaglin1632
6 ай бұрын
Is it possible to send a lower to you for buffer tube adjustment and restaking?
@ogongo2029
7 күн бұрын
Whats that green lower holder in vice called?
@boriquais
10 ай бұрын
SOTAR have you staked griffin endplates? I destroyed 2 good quality punches and didn’t even scratch the finish.
@Randy_84
11 ай бұрын
Red loctite 😂😂😂
@Shackleford_Rusty
11 ай бұрын
Just what I’ve been looking for, just snagged one. Thanks Chad
@goinhot9133
11 ай бұрын
All seems well but the punch seems anemic.. even after several cycles of the punch the divot was minimal.
@TROY-MCCLURE-1991
3 ай бұрын
What digital torque wrench were you using?
@TROY-MCCLURE-1991
3 ай бұрын
What digital torque wrench do you use?
@Sirmellowman
11 ай бұрын
you staked and torqued that all down without the rear takedown pin installed? why?
@homeFall1
11 ай бұрын
demo purposes I am sure
@Bodhi1satva
11 ай бұрын
Where can I find that green vice?
@jimmyanna
2 ай бұрын
What level castel nut are these - 3, 2, or 1?
@Shootsmith
11 ай бұрын
PWS Primary Weapons Systems Ratchet Lock Castle QD Nut End Plate
@printingwithpeek4897
11 ай бұрын
Those are not used for a reason. They're not a spring-loaded detent, and those small spires that are made will shear off if ever removed.
@mapled3135
11 ай бұрын
@@printingwithpeek4897so. Castle nuts aren’t made to be re used.
Пікірлер: 178