You saved my ass! I spent all day trying to vacuum bleed my brakes after installing a new front line. I used your method today and it worked like a charm! Thank you!
@Dan-rc4cx
3 жыл бұрын
your welcome. This made my day that I could help just one person.
@flfbsphatboyblue8970
2 жыл бұрын
How do you bleed out the old fluid from the ABS valves without actuating the control solenoids? That is the purpose of the computer.
@robertglancy4474
2 жыл бұрын
I just got done doing my brakes, non-ABS 2012 Road King and used this method. It worked pretty well, rear was easier then the front. On the front I have dual brakes, I cut about an 8 inch piece of hose and stuck it on the clutch side valve and directed it towards an oil pan so I didn't just have brake fluid squirting everywhere. Soon as I opened the valve it just started to flow without me pushing on the other side. It cleared out that side pretty quickly, I shut off the valve and started pushing it up to the master cylinder. I was using the plastic syringe with about another 8 inch piece of 3/16 inch hose I believe and just kind of peaking over the top of the MC while I pushed the plunger. Got a big squirt I wasn't prepared for out of the MC and had to stop to wipe off the break fluid that shot out. Went a lot a slower emptying out the MC with a turkey baster and pushing more fluid in and did that a few times and got it done until it tested "good" with my moisture tester and didn't have any air in the lines and no spongy brakes job can be done by one person so thanks for the video
@Dan-rc4cx
2 жыл бұрын
You’re welcome. I’m glad I could help.
@curtgeisenhaver8834
4 жыл бұрын
My kind of video. "Push the fluid, open the fucking valve, fuck... Etc". Thanks man!
@ricardodelatorre2498
4 жыл бұрын
Video makes total sense, and has worked well for my factory calipers, however, on my 2020 FLHX w/ABS, If I am installing a new set of front (chrome) calipers would I follow the following procedure? THANK YOU ! ! 1. Remove existing front left caliper 2. Install new front left caliper 3. Remove front master cylinder cap 4. Squeeze front brake lever to push caliper cups towards rotor 5. Now bleed front left caliper The above sequence makes sense (my assumption) because Im trying to fill the caliper with fluid prior to bleeding. Make sense? Thanks again! Love your videos!!
@Dan-rc4cx
4 жыл бұрын
Ricardo De La Torre I would install all the hardware, push fluid in as in the video. Put master cover on and pump up the brakes. Then do the procedure again after the calipers travel out to the rotors to ensure enough fluid is in the system with no air bubbles.
@marlonmills3257
5 жыл бұрын
😂😂😂 the neighbor and scotch!!!!
@nick7980
2 жыл бұрын
How do you bleed the abs?
@kitdman5749
5 жыл бұрын
Im assuming you keep the master cylinder lid closed during this whole process? Nice tutorial!
@Dan-rc4cx
5 жыл бұрын
Actually the master can sit open and should. Because the second side bleeder screws are open while you push the fluid the master will not fill. Then when its time to push the fluid up to the master you are able to see the master fill up and see the few bubbles dissipate when you tap on the master body.
@ghostghost6268
4 жыл бұрын
@@Dan-rc4cx Additionally, once you have the fluid through the system....squeeze the front brake slowing and it will move air that is in the line out through the master cylinder housing on the handlebars. ...squeeze until no more air bubbles. Great Vid
@dantehawkins6893
5 жыл бұрын
Nice advise.. How does this work if you are replacing your rear lower brake line with abs on a HD Breakout?
@Dan-rc4cx
5 жыл бұрын
Dante Hawkins this works for all brake systems on any vehicle.
@dantehawkins6893
5 жыл бұрын
@@Dan-rc4cx Thanks for the tip....
@jvirgil89
5 жыл бұрын
I can’t push the fluid out to save my life. It’s like there’s a damn rock in my bleeder valve. I’ve tried both sides.. any tips? Brand New stainless lines
@Dan-rc4cx
5 жыл бұрын
Jeremiah V not sure man. I’ve never had that happen. I would try pouring Fluid in the master and pump it. See If you can get any flow down to the caliper that way. Obviously though something isn’t right.
@jvirgil89
5 жыл бұрын
DYNATRASH so.. tell me why I was turning the wrong nut. The whole nut to remove the bleeder valve from the caliper. Lmao. I’m new to Harley’s give me a break. Thanks for the video and help brotha
@jvirgil89
3 жыл бұрын
@Danny Harbin bro you've left HELLA comments .. after comments bashing HD. Every brake system needs to be bled.. car or bike. So that makes it.. a POS? Lol are you happy you got a reply finally? You feel special? Okay Danny goodnight
Пікірлер: 26