Well done. I really wish @Hobbywing would fix the sensorless issue on these
@sammybaka
5 ай бұрын
Thank you and I totally agree. It's just a surprising miss from hobbywing.
@jalenortiz3623
Ай бұрын
Hello what this issue is it where the esc just keeps beeping I can’t get it to get any movement just the gyro works. I tried programming it already any help pls
@DudeWiththeClue
5 ай бұрын
awesome vid Sammy! I have been wondering about possibly changing to a sensored motor, but this may have to be an upgrade in the future.
@sammybaka
5 ай бұрын
Thank you. If you are planning to run a sensored system, this is a great choice. This is the ESC I see most often on cars being raced.
@PushaBee
Ай бұрын
Hello this might sound like a dumb question but what battery does the ezrun mini28 take? I got one in today and I bought a battery that’s jst-xh and it’s big. Thank you in advance!
@sammybaka
Ай бұрын
This esc expects a 2S lipo. The choice of connector is up to you and the batteries you buy. A common connector used for this scale is JST-PH (3 pin, 2mm pitch). This is what I use in all my cars. Many batteries come with jst-ph but I've also seen small lipo packs with one jst-xh lead. jst-xh is conventionally used as the balance port.
@PushaBee
Ай бұрын
@@sammybaka thank you!!!! I was losing my mind trying to find out what the connector was called.
@ZackoTv
5 ай бұрын
Anyone know the name of the white connector at 4:11 ? I need to make a cable more long but its not a classic jst-zh :(
@sammybaka
5 ай бұрын
I just examined the connector closely and busted out the caliper. I'm now pretty sure it's jst-zh 3-pin 1mm pitch.
@mc26275
5 ай бұрын
Could this work in the Sai Lai buggy chassis?
@sammybaka
5 ай бұрын
For sure, but please note that almost all sensored motors do not have the D-shaped end bell that fits into the buggy motor mounting system. For example, this GL sensored motor has a flat end bell. Therefore, to use this motor, you will need to drill two holes in the front motor plate so you can use m2 screws to secure the motor.
@mc26275
5 ай бұрын
@@sammybaka Thank you for responding. Presumably, the ESC would work fine with a Kyosho XSPEED brushless sensored motor?
@sammybaka
5 ай бұрын
@@mc26275 Actually I'm not sure. Kyosho did something weird with the new sensored motors where the sensor cable is 6-wire, rather than the usual 5. I believe the extra wire is for temperature telemetry but regardless it's certainly not a drop in option for this ESC.
@mc26275
5 ай бұрын
@@sammybaka Thanks for the insights!
@MultiAp101
5 күн бұрын
What receiver and transmitter are you using
@sammybaka
4 күн бұрын
I use the Flysky NB4 transmitter. The receiver used here is a DasMikro afhds3 micro receiver.
@MultiAp101
4 күн бұрын
@@sammybaka I’m using the mini28 ESC and flysky GMR receiver and have not had any success getting the receiver to go into bind mode.
@sammybaka
4 күн бұрын
@@MultiAp101 i have that receiver too. what did you try to put it in bind mode?
@MultiAp101
4 күн бұрын
@@sammybaka hold the bind button on the receiver and turn on the ESC. once the esc is on and the receiver starts flashing release the bind button. The receiver should continue to flash showing it in bind mode. Mine does not do this, once I release the bind button it stops flashing. For some reason it will not go into bind mode. I’ve tried 3 of the same GMR receivers and they all do the same thing. My ESC has not been calibrated as it takes the controller/transmitter to do so but I cannot bind it to do so.
@sammybaka
3 күн бұрын
That's odd, especially with 3. I don't have any solid suggestions here. Make sure the surface you are working on is not conductive. Maybe try a different esc? Maybe try to bind anyway. With the GMR, nb4 needs to bind in enhanced receiver mode.
Пікірлер: 23