You don't need to hammer anything or use a rag or wrenches - the bar weights are held in with a spring clip with a release tang at the end of the bars (one above and one below) - you simply put the tip of a flat-blade screwdriver into the gap between the end of the bar and tang, push and twist - and it releases the spring clip pin from the holes in the bar, and you just slide the weight out.
@UKbiker73
9 ай бұрын
You are correct, but if you have heated grips fitted you can’t roll back the glued grips to expose the lugs so this method is helpful in that situation if you are planning to fit Handguard.
@jmo2752
9 ай бұрын
@@UKbiker73 you shouldn't need to roll the grips back unless you want to poke something though the holes in the bars to release the pins - the tangs are at the end of the handlebar, and you can just put the tip of a flat-blade screwdriver between the tang and the end of the handlebar, push down and twist.
@alexanderwright9064
7 ай бұрын
I hope this works. I will try .!@@jmo2752
@mattyoung2791
6 күн бұрын
You've saved me so much time, I appreciate it, thank you!
@sandwaves5642
Жыл бұрын
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@gs-nt6nf
Жыл бұрын
Your method works very well. Thanks.
@irishrover63
4 жыл бұрын
I didn't have any issues removing mine. That doesn't look like Dublin. :)
@Followthepinas
Жыл бұрын
Thanks for the video this method worked like a champ!
@Casey_Schmidt
4 жыл бұрын
This is a clever technique, I like it! I'll be fitting hand guards on my CB500F over on my channel soon, I'll give this technique a try. Thanks for posting!
@mitsubishilancer17
2 жыл бұрын
Did it work, i also have a cb500f
@Casey_Schmidt
2 жыл бұрын
@@mitsubishilancer17 I actually have short a video about how I did it on my channel. It will be a lot clearer than me trying to explain it here lol
@orion310591RS
4 жыл бұрын
Another solution is to remove screw, and use "half round nose pliers", to press pin one then pin two. It only needs to go under the rubber for like 2cm. Then it will go out smooth.
@shiftupadventure
4 жыл бұрын
Cool, yes that's what's holding them inside 👍
@dev77cmd
2 жыл бұрын
Thank you. Was skeptical to remove the stock bar ends because If I screwed it up, I was going to have to haul the bike to the workshop so I could get it fixed. With your method it was easy peazy!
@skrid2577
3 жыл бұрын
Thank you so much! I was struggling and trying to unscrew the end piece with no luck. I have the exact same bike and really love it!
@ninobongiovanni4447
9 ай бұрын
Didn’t work I was there for an hour 😂
@TraceurTube
2 ай бұрын
Bummer, I tried too (transalp), didn’t work. What bike is yours?
@ninobongiovanni4447
2 ай бұрын
@@TraceurTube CB500F, it was a mission to get them off. Theres a pin that you need to push in and also on throttle side you need to disassemble everything and be careful not to break the plastic sleeve under the rubber.
@newbierider3553
4 жыл бұрын
Before the gentle hammering, did you unscrew a little to give some space for "iron thing"?? Thx
@shiftupadventure
4 жыл бұрын
Hi, no, no need. Pull ends out slightly with hands by rolling, just enough so you can place the wrench inside. 👋👍
@eddiewu2336
2 жыл бұрын
Hello, how much more vibration did you feel after you removed the in bar weight?
@shiftupadventure
2 жыл бұрын
No noticeable difference (I do have grip puppies to reduce vibrations) 👍
@xli90
Жыл бұрын
Thank you,Sir! The best way to remove the whole thing, only took me 5 mins to remove them. My bike is cbr650r, so I guess this method good for all Honda bike.
@roko-ui1dv
2 жыл бұрын
Cekan svoja zrcala za CB500F i fala ti unaprid na ovome 🤝!
@noorulameer265
3 жыл бұрын
How to remove end bar using srew driver instead of pulling out like this? Mine also follow like this video. But i want to remove using screw driver. It is so hard n dificult. Any ideas?
@paranoza3573
Жыл бұрын
Thanks brother, worked like a charm
@Shoreditch
11 ай бұрын
Looked prepped to me.
@bertbirge7864
3 жыл бұрын
Very helpful. Thank you so much!!
@passinthru4328
3 жыл бұрын
Good job. Thank you for sharing.
@Jason.W.
4 жыл бұрын
Took it off very easy with your way. Thanks. My rubber is lost deep inside the bar. Any tips on fishing it out? My longest screwdriver can’t even reach it.
@shiftupadventure
4 жыл бұрын
Thanks, happened to me too, I think we pulled it out too fast. I was able to get it out with thin metal wire. Goes easily out once you lock it.
@Jason.W.
4 жыл бұрын
ShiftUpAdventure ya trouble was finding a wire lol. Thanks.
Пікірлер: 33