🟣Hi my arduino friends, I used this arduino board for a cnc. The actual 12v power for the motors was obtained from the 12v jack on the arduino board...and then one day I connected the board to the computer but it didn't connect.. 🟣I think the board was damaged because the motors got too much Current .... 🟣I couldn't get this board to work again.. 🟣I bought a new Arduino board
@EdTechPraveen
7 ай бұрын
Yes bro for me also happened like that , I am trying to buy new Arduino
@takshivkashyap743
2 ай бұрын
Your Problem was solved or not ? if solve please help me because i am facing same problem like you.
@creativehimasha2007
2 ай бұрын
@@takshivkashyap743 No bro ....
@takshivkashyap743
2 ай бұрын
Ok bro..
@takshivkashyap743
2 ай бұрын
@@creativehimasha2007 hloo bro... mera koi bhi arduino uno bord recognize nehi ho reha hai..... me re pass 16u2 chip Vala hai arduino mujhe isko koi driver bhi nehi mil reha hai aapko to ek bord connect ho reha hai lekin mera nehi ho reha please help.....😢😢😢 mujhko 1 month hone Vala hai lekin koi solution nehi mil reha hai 😢😢😢 please......
@winzee3687
5 күн бұрын
I have changed the usb port from 3.0 to 2.0 and it worked for me
@RaviShankar-kk8ld
Жыл бұрын
brother i have same problem please tell me a solution Arduino uno port not showing in device manager
@ReeshavGhosh200
Ай бұрын
Me too 😭😭😭
@Yoyo123jjsd
Жыл бұрын
I had this problem too, and i thought my board was short or something , but here is a solution , make sure the arduino agent is running or close it and open it again
@10millionviews27
11 ай бұрын
Arduino agent means?
@takshivkashyap743
2 ай бұрын
means of agent ?
@Yoyo123jjsd
2 ай бұрын
@@10millionviews27 the software you use if you are coding from browser
@TechExperiMents2010
Жыл бұрын
i get this problem in arduino nano
@sivayarajodu2394
Жыл бұрын
If you got the solution please make another video bro 🙏🙏🙏🙏
@Wesley3268
5 ай бұрын
imagine uploading code to your arduino but it doesn't load, you tried many attempts to solve it but it's just because the arduino isn't plugged in yet
@ichbin-bp3oh
11 ай бұрын
If you bougth it new, you have to install a driver, because many clone/fake arduinos have a 12MHZ chip not like the original 16MHZ
@akhileshshetti1737
5 ай бұрын
How to install the drivers? I have the same issue, my laptop and ARDUINO UNO both are new and hence when I upload the code the connected sensor is not working.
@advstudiocreation6559
Жыл бұрын
same problem please make full video on it
@softkacpix
9 ай бұрын
Did you tried arduino ide, it would detect arduino as Normal if you will chose a Good board
@damarmurub628
Жыл бұрын
Bagaimana solusinya bang
@harisooriya
9 ай бұрын
yea bro me too but i forced it to become a com port but it didnt
@manuabraham8888
9 ай бұрын
When i connect my arduino uno to the laptop the port in the tools doesnt appear enabled
@divyanshumishra9163
4 ай бұрын
I have the solution. Install the ch341 driver and don't turn on wifi during and after installation for 15mins then connect board open Arduino ide and you are set
@takshivkashyap743
2 ай бұрын
its not working bro because in this case have atmega16u2 usb to serial chip not ch341 . okkk
@divyanshumishra9163
2 ай бұрын
Bro if it doesn't work it means you have a good clone or original Arduino just use original drivers located in programfiles(x86) for v1.8
@hareshrajput79
Жыл бұрын
Bro same problam give tha solution
@user-he3yj3tz5b
2 ай бұрын
Cable nam kiya he
@TT-nd8sy
Жыл бұрын
Things are so shakey it's hard to tell what's going on. But I get that you're not getting an insertion tone for the bad board. I can see you have the board with the pull-down for the HWB on the transceiver chip. If it were mine, as my next step I would plug the board in and jumper the RESET and GND on the transceiver's ISP header (the one nearest the USB jack). If you are not sure that you're connecting the right pins in the ISP header, use a resistor of say 220ohms to about 500 ohms or so to make the connection; that way you shouldn't hurt anything if you try to connect 5v and ground or something. If the transceiver 16u2/8u2 chip has the Atmel DFU bootloader on it you will hear the tone in Windows and it will show up _somewhere_ in device manager as a ATMEL DFU Device or ATMEL ATMega18/8U2 or generically as a DFU programmable device, depending on what you have installed. So, if you still have the board, try that and let me know what happens. I'd tell you what I'd do next. If it shows up as a DFU device, that's a good sign. If it doesn't do anything, that doesn't necessarily mean you're out of options.
@creativehimasha2007
Жыл бұрын
Thank you
@pruthvirajhm
Жыл бұрын
Indeed i am facing the same. This problem started in my board all beacuse i tried to run a Dc motor through arduino uno . Later the very next moment when i tried plugging it to pc it was not connecting. It didnt show the com port. So i tried by shorting the 5v pin to reset pin it turned on and it did connect to pc. But the issue now is it is though it is connected it doesn't accept the code to get uploaded, it return an error message. So is there a way i can get through this ?
@EdTechPraveen
7 ай бұрын
Same problem Iam also facing bro
@EdTechPraveen
7 ай бұрын
@@pruthvirajhm did you find solution please help me
@pruthvirajhm
7 ай бұрын
@@EdTechPraveen if you own a arduino uno and you are facing this issue. Then the only thing you can do is try replacing the atmega chip which is on the board. It will nearly cost you around 200₹-300 ₹.
@bachadragjod.
4 ай бұрын
Down load drive( CH34X INSTALL WINDOW V 3.4)
@sumalathapanduga231
Жыл бұрын
Bro it's no a big problem just connect the arduino to laptop go to tools and select com5 or for some arduino it shows com3 just select it and select with arduino is yours done now you can upload the code
@bro_scooter
11 ай бұрын
But port 3 is just gone for me, there is no port 3 only 1
@brandonjacob3897
11 ай бұрын
same here
@bro_scooter
11 ай бұрын
It's a easy fix I didn't push the cable to Arduino completely in
@TRAZExYT
10 ай бұрын
It depends on your computer,it doesn't have to be port 3, it can be any other port number like com7,com4, e.t.c like that@@bro_scooter
@NageshWaran-xu6lt
9 ай бұрын
@@bro_scooter goog🎉🎉🎉❤
@etlyrics5329
5 ай бұрын
change the ic
@taigongo988
Жыл бұрын
Mera bhi same problem
@muhammadhussain1392
Жыл бұрын
Same this problem
@creativehimasha2007
Жыл бұрын
I bought a new board . not solution for there.
@bachadragjod.
4 ай бұрын
The Arduino Uno smd have many problem😂😂😂😂
@kuntalmaji7205
Жыл бұрын
Bhai esp8266 same problem device manager mein nahi aa raha
@carlangelodalangin8001
Жыл бұрын
Same problem, have you fixed yours?
@dharanidharan9984
Жыл бұрын
instal driver
@takshivkashyap743
2 ай бұрын
which driver ?
@advstudiocreation6559
Жыл бұрын
bro I just facing this problem from three days
@EdTechPraveen
7 ай бұрын
Did you get the solution??
@JustBeingme-yp2kt
6 ай бұрын
Pls share the solution
@advstudiocreation6559
Жыл бұрын
how can I contact with you for fix this problem
@user-iz6dx1be2o
Жыл бұрын
How did you solve the problem?
@Hamody_
Жыл бұрын
🙏 please solution
@BloxForLifeYT
10 ай бұрын
.
@BloxForLifeYT
10 ай бұрын
.
@takshivkashyap743
Ай бұрын
hey @creativehimasha2007, I bought new arduino board it's recognize and configure but when I upload code to in "avrdude: ser_open(): can't set com-state for "\\.\COM6" Failed uploading: uploading error: exit status 1" WHAT CAN I DO PLEASEEEEEE HELP.......
@creativehimasha2007
Ай бұрын
choice correct Port and board type and upload code
@takshivkashyap743
Ай бұрын
@@creativehimasha2007 hey i already choose correct board and port. BOARD = Arduino UNO, PORT = COM6 (seeing in device manager)
@takshivkashyap743
Ай бұрын
@@creativehimasha2007 and thease same problem in my all computer or laptop including mobiles..
@takshivkashyap743
Ай бұрын
@@creativehimasha2007 and second one arduino UNO same problem dosn't recognizeing by device manager with 16u2 chip
Пікірлер: 72