Replacement Oil Burner Electrodes on Amazon - amzn.to/2Rtjsbi Replacement Oil Burner Nozzles on Amazon - amzn.to/2RurMHM Riello Pump Strainer Screen on Amazon - amzn.to/2GKrpEG Replacement Fuel Oil Filters on Amazon - amzn.to/2rYQPnP Boiler Cleaning Brushes on Amazon - amzn.to/2SQq94L
@serega4087
Жыл бұрын
I broke my neck trying to buy same ruler on internet. Where did you get it?
@billsmith2212
5 ай бұрын
As a DIY I am careful when I touch items such as this . On my Riello , I found 2 different nozzles were used by past service companies . I called Riello and was told BOTH were undersized , based on boiler GPH . I put in what Riello recommended . I have also seen " pros " on video adjust the electrodes " by eye " and use odd size wrenches , and even pliers , on the oil line and bleeder . Which is unbelievable that they don't have the metric sizes if doing this daily . Or even a small adjustable wrench . Great video . Always be aware WHO you are watching and WHERE the information comes from . It may " work or be fine " , but what are these manuals and specifications for ?
@Ratman_Bejo
3 жыл бұрын
hello friends, how are you there, I'm Ratman from Indonesia, one of the repairmen for all Burner brands, one of which is the Weishoupt, Riello FBR, Baltur, Ecomark etc.
@waynedagostino541
4 жыл бұрын
You can also use a 3/16 Allen wrench put it thru slot on ceramics to retention head to center and set gap
@jcstevegigs
3 жыл бұрын
Great video. I just bought new electrodes and transformer
@anthonyconcialdi3659
9 ай бұрын
Thank you for this video. One thing I did not see mentioned is the distance from the top of the electrodes to the top of the nozzle . I see a 4mm gap between the electrodes and a 5mm distance to the center of the nozzle. What is the height over the nozzle?
@paulestridge8734
Ай бұрын
I can’t loosen the screw to slide the porcelean block for making the necessary adjustment. It appears as though it’s rusted in place and I’m afraid of breaking it. Do you have any suggestions?
@shawnmckenna7513
Жыл бұрын
I found it helpful
@berniemcneal1353
3 жыл бұрын
There are notches in the electrodes, do they have to be lined up with springs
@WinglifeCT
4 жыл бұрын
Hi thanks for the video. I’m getting oil into the electrical I believe the oil is coming down the electrodes into the electronics. Do have any idea what my problem is?
@sintayehuaddisu7969
2 жыл бұрын
Hi there. I was in a lot of trouble. Burner got up and worked for 30 seconds. It turned off. I changed the nozzle
@tablespoon888
2 жыл бұрын
Are the points important..was have hit and miss lighting...readjusted the electrodes. But noticed points are gone
@victorboisdenghien361
Жыл бұрын
tthe most important 5mm measurment you didnt show enough ??? air intake please show starting point how to read the smpke and final adjustment.
@SocaRehab
3 жыл бұрын
What's the correct name for the measuring tool you're using?
@milosavitch1
6 ай бұрын
less waffle = better watch time percentage
@robe5000
4 жыл бұрын
My Riello 3M has been mis firing when initailly calling for heat, it trys to fire 4 or 5 times before it stays lit, it does however always lights and runs fine. Any suggestions when I should look for?
@easy_two
3 жыл бұрын
Hello. Same story here. Did you ever find the cause/resolution for this issue? Thank you in advance.
@ajafferji91297
10 ай бұрын
👍
@gregfitts-bc6fs
Жыл бұрын
Old furnace guy showed how to use a nickel as a Guage...Is this close ?
@superargo4701
5 жыл бұрын
Great video! I think this is what I need to correct on my Riello 5. Its recently been taking 4 to 7 starts before running. I've checked the photocell and its fully functional. Fuel is present, as there is a fog of atomized fuel in the burn chamber. What would be the most likely culprit for causing the elongated no-ignition? Adjustment of the electrodes?
@easy_two
3 жыл бұрын
Hello. Did you ever figure out the cause/resolution? I am also getting a delayed ignition with 4-7 tries before ignition occurs.
@superargo4701
3 жыл бұрын
@@easy_two I managed to get it down to one misfire per ignition. I suspect it is to do with the photo cell feedback loop in the power module. I had touched up all solder connections on the module circuit board. Polished the connections of the photocell. I suspect the photocell is the culprit.
@superargo4701
3 жыл бұрын
@@easy_two let me know how you fair out. I'd like to zero out the misfire.
@greganderson8416
2 жыл бұрын
Cleaning and adjusting the electrodes resolved this for me. There was significant black soot buildup on the ends which I scraped off with a flathead screwdriver.
@TAGUPNBLUE
8 ай бұрын
Those electrodes are shot there is a Beckett tool to set the tips the same tool does it for the air diverter redo the video
@mmack3286
4 жыл бұрын
If the ceramic part in electrodes where broken could this be a problem for burner to start?
@mmack3286
4 жыл бұрын
Thank for fast response. If the ceramic become brittle and small part had broken off while servicing it could this be a problem for the burner to start? As I'm having problems on the riello g5x model it's firing up ok then it's going off but fan still running but it doesn't go to lock out keeps trying to start up gets to 8 bar oil pressure then goes out??
@mmack3286
4 жыл бұрын
I've done that plus the electrodes are sparking but won't know until I get a new photo cell tomorrow to see if it this.
@tatendampofu8289
2 жыл бұрын
Am having a burner witch is cutting after 17 sec
@joshwilley3173
7 ай бұрын
My fkin nozzle is stuck on the igniter. No matter what i do i cant ge the nozzle off. Tried a blowtorch to loosen it. Nothin.
Пікірлер: 32