Beautifully Done @KarelyHall I just got an M1 xTool. This was a thorough video yet not too long. I look forward to completing my first glass engraving (with the Chalk Paint). Keep up the great work!
@makingmemoriescrafts8507
11 ай бұрын
I can't thank you enough! You did such a great job at explaining this entire process. I was so intimidated until I watched you. ❤️
@nvargas48
4 ай бұрын
More than helpful! I hadn’t touched my rotary tool although I’ve had it for a couple of months now, because I hate reading instructions and all the parts were intimidating 😂Thanks to you I put the whole thing together! I would love to see a video of acrylic engraving and cutting! I can’t get the right settings to cut!
@lonewulph
Жыл бұрын
This is a great video. Just ordered my M1 after months of research and of all the videos I watched, this was the most informative by far. Thank you!
@Wongster360
Жыл бұрын
Thank you for such a great and detailed video. It helped me get over the anxiety of setting up my RA2 Pro for the first time. I just finished my first set of wine glasses as an anniversary gift for my brother and they turned out awesome!
@grayfox9769
2 ай бұрын
Thank you so much for posting this video. You helped me figure out how to use this RA2 accessory. Subscribed. 🙃
@vondabrooks9467
Жыл бұрын
Absolutely great video. Thank you! Thank You! THANK YOU! Just what I was looking for.
@andreaibañez-n6d
Жыл бұрын
Thank you very much for your video. It has been a great help to me to get started in wine glass engraving.
@leeannalexander4705
Жыл бұрын
Great video Karley! Hopefully this will give me the push to try my first wineglass 😉thanks for all you do
@dutchmeikuh8822
Жыл бұрын
Very helpfull in many ways, thank you so much
@GloriaAnnRodriguez90
11 ай бұрын
best tutorial I have found!!! Thank you!!
@KarleyHall
11 ай бұрын
Thank you!! My xtool series has been so fun to film! I hope to get back to it soon! 😅
@hernz.gonz.2990
Жыл бұрын
thank you thank you very much for explain all this m1 tools. i am amiguina thank you so much!!!!!!!!!!!!!!!!!!!!!!!!!!!! ❤❤❤❤❤❤❤❤💯💯💯💯
@theboredcreative
2 ай бұрын
This was excellent Karley!
@charleesoleil8510
5 ай бұрын
Excellent tutorial! I’m waiting for my M1 this week and I was wondering, would this painting technique work on acrylics?
@susanakuehne-molina3716
Жыл бұрын
Thank you very much. A very good video Karley! 😍😍😍
@tiffaniwilson9133
11 ай бұрын
Thank you so much for your video! It was a huge help! I’ve been etching my glasses by hand the past year, along with so many other things and this tool leveled up my small business 🎉 *Question: I had the same l chalk paint on hand that you used. What I noticed is that it came off most of my glass but the area where the design was most intricate, it did not. I’ve scrubbed and can’t get it off. Any suggestions?
@Manukapu
8 ай бұрын
I notice that you XCS has measurements IN and not MM. How did you convert?
@Shefroniabrooks
5 ай бұрын
Did you figure this out?
@janburden8370
10 ай бұрын
Thank you! Great video. Quick question - have you ever had burn marks or vertical dark marks after engraving?
@CthePHOTOG
8 ай бұрын
Great video. My only problem is when I'm framing the glass the chuck rotates the glass around twice and not in the area where the design is set to go. I have everything lined up and the design is in place. Do you, by chance, have a fix for this? Thanks.
@ThePapa1947
Жыл бұрын
Great video. I like the chuck facing out as well but you need to move the whole setup to the other end. The drive gear is on the wrong side to just turn the chuck the other way. I wish you did not have to do that.
@ginamariegarcia9461
9 ай бұрын
Thank you so much
@gemmad1990
11 ай бұрын
This is amazing thank you! I have some square glass jugs- do you think this is something that I could engrave with the M1- would the rotary tool be required? Thank you
@stevejones01
Жыл бұрын
The thing on the left side that supports the glass is called a "tail stock" and the tiny little screws are called "set screws".
@KarleyHall
Жыл бұрын
Thanks!! 🙌🏼
@vondabrooks9467
Жыл бұрын
Don't now if this would be helpful to you or not; but I got the same cracking around the edges you were speaking of (not as clean a cut)with the settings you used, so I played around with the settings a bit and made an adjustment in the speed (slowed to 73) and the Lines per cm - changed to 200 (tried 140 - was ok, 180 - a little better). Give it a try. Hope it helps.
@KarleyHall
Жыл бұрын
Ooh! Thank you so much for the comment! I could not figure out any settings that were crack free- even with a test grid! I cannot wait to try these. I’ll definitely report back! Thanks again! 🥰
@juniorrod3035
2 ай бұрын
Can I use any chalk paint?
@mightyminisuk4295
Жыл бұрын
hey so i see a problem, if you turn the chuck part round the opposite way to do things with a handle, then how does the belt go on as its then in the wrong place?
@fabiolarichards4506
10 ай бұрын
Will any chalk paint work?
@jillcastillo7057
Жыл бұрын
Thank you for this! Do I need a rotary to with the support thing for wine glasses? or can I just somehow prop the glass in there to that it is levelled and stable? THANK YOU :)
@KarleyHall
Жыл бұрын
As long as it stays even when it rotates- you’re good to go! When you frame it- you should be able to tell if it’s shifting.
@juliel6253
Жыл бұрын
Hello, Karley. My sister and I are considering a tool such as this. I would be most grateful if you could tell me the difference between the xTool and a Glowforge. We're just not sure which way to go. Cost is not a major concern. TIA
@KarleyHall
Жыл бұрын
The glowforge is a CO2 laser and the xtool is a diode laser. Diode lasers are much less powerful and cannot cut through light colors since the light is reflected. I would recommend a glowforge if cost isn’t an issue with the caveat that it cannot engrave cylindrical objects like cups! What are you looking to use your laser for? They both have so many benefits so it really just depends on what you want to use it for!
@Hanane30
Жыл бұрын
Bonjour can l use it thaïs rotary with laser pecker 3 ??merci
@aliciagorden4882
9 ай бұрын
I have this glass. Is your glass from dollar tree?
@ginamariegarcia9461
9 ай бұрын
StarCraft is out of stock. Is there another brand
@basook6116
Жыл бұрын
have you try permanent black marker?
@KarleyHall
Жыл бұрын
I haven’t- but you’d need something pretty opaque! Like a paint marker!
@basook6116
Жыл бұрын
@@KarleyHall thanks. permanent black marker is real black
@KarleyHall
Жыл бұрын
@@basook6116 yes- but sharpies (for example) are actually pretty translucent!
@basook6116
Жыл бұрын
@@KarleyHall yes, like glass... thanks
@KarleyHall
Жыл бұрын
@@basook6116 yes- so that won’t work! You’ll need something you can’t see through :)
@roccocroce
Жыл бұрын
you'd have to use AT LEAST one coat, right? =p
@jppalm3944
Жыл бұрын
Couldn't you fill a bag of sand and insert it into glass
@KarleyHall
Жыл бұрын
I would think so since sand isn't flammable!
@zseitung
5 ай бұрын
But a bag might be?
@hernz.gonz.2990
Жыл бұрын
ups, excuse me , beginner!!!!!!!
@lisamariedesignboutique
Жыл бұрын
I’ve had my RA2 pro for months now but finally took it out of the box watching your video was extremely helpful, thank you so much! 🤍
Пікірлер: 51