Thank you for this video. Very helpful. Went thru all 3 steps you indicated and the fuse was my issue. I hate to throw out things that are salvageable. I appreciate you sharing your expertise.
@dksail6724
2 ай бұрын
Thanks so much for putting this online! My Fluke was not working. After watching your video, it was a positive test lead. Not sure I would have checked those as they seem robust. Go KZitem!
@hotchihuahua1546
3 жыл бұрын
Simple but so often overlooked , good video ! 👍👍
@randymueller2349
Жыл бұрын
Thanks for the Video, I've personally also had these same 3 common failures with my Fluke 87 over the years. I also own a MAC Tools ET-332 Multimeter that has a broken Red Voltage Test Lead Socket, this Meter has 3 Red Sockets one of which is labled CX that I've never used, so tonight I de-soldered both the V and the CX Sockets and re-soldered the CX socket in the V position. My ET-332 Meter is now usable again. Randy AKA randog311
@Kasal269
3 жыл бұрын
Bro very important technical information given regards fluke digital multimeter. Thanks 🙏🙏 india
@JaykeSapalaran-iq3qs
Ай бұрын
Great video tutorial 👍, thank you for sharing your knowledge ❤️
@pbryan4
Жыл бұрын
Respect man! Very good info, I was about to through mine and buy a new one. THK!
@sweetiepienumber1
27 күн бұрын
DIYer here. I accidentally left a decent Ideal brand clamp meter in the hot sun. Now the screen dims and/or is blank. Do you think it is cooked? The joke was not intended. Thank you.
@bradforddrake8633
Жыл бұрын
My multimeter works okay for voltage and amps. On the ohm scale with the speaker function, my meter is beeping WITHOUT the leads touching each other. I know this wrong. Is there a fix for this OR should I buy a new meter?
@jondoe9581
2 жыл бұрын
Thank you, one lead was looking fine nothing obviously wrong however it wasnt working. Great video thank you sir
@andrewkhchan
2 жыл бұрын
Informative video 👍🏼 as my trusted multimeter just broke down. Wonder you can tell me the value of the fuse ? It does not turn on at all. Thx
@Boardcousin
2 ай бұрын
This is unrelated but i have two LED's that give different brightnesses no matter if i hooked them up to the other ones connection. Will they lose the ability to light up after multiple uses?
@christopherperchanpertubal4521
2 жыл бұрын
hello friend me Christopher Pertubal from Bued Zone2 Binalonan Pangasinan it's nice and so interesting your KZitem channels to watch thank you Rusty Dusty's automotive repair!!
@josepeixoto3384
2 жыл бұрын
Good deal,but that was no help for me; the varistor was exploded,replaced the fuse, and i think the whole shibang had gone bad, no display at all; fuses and battery are ok; getting another multimeter; i think that 220 V were tested by mistake when in the ohms scale; would that blow it totally?
@ahsanmehmood2107
5 ай бұрын
Very good wark❤
@zouma7734
3 жыл бұрын
Hello. please i am looking for lcd screen for fluke 87 do you know a site that sell it with other spare parts. Regards
@doasangambler9013
2 ай бұрын
soon as you got the back of i knew thanks
@stefchristian7165
Жыл бұрын
Thank you for this video. I have a Voltcraft VC222 multimeter and the letters from the screen are not clear sown on the screen (they are half of them shown on the screen and they are showed and not on the screen). What could be the problem with my multimeter? Could it be fixed, or shoud I buy a new multimeter? (I am just an amator user - what should I buy (If necessary))?
@oswaldfraser4946
Жыл бұрын
Thanks for your information.I have a fluke 77iv when it's on all the functions would come up on the display it would stay like that regardless of how you rotate the switch.Please help
@esronthomas207
2 жыл бұрын
Thankyou very much this video help alot, but my problem is that, my multimeter turn of when I switched the dial so how would I go about fixing it
@davidregen1358
2 жыл бұрын
Is there a place to learn about multimeter LCD inputs? Looking for a way to pick up LCD signals to control an external device.
@mize_yir_bizz
Жыл бұрын
try looking up ir sensors, maybe from an old t.v. remote.
@ABRUSAHAELEKTRIK
2 жыл бұрын
Thanks for sharing.
@debihsofiane3229
2 жыл бұрын
Thank you
@Eman-vp5wk
Жыл бұрын
Any thoughts on what could cause that multimeter to power down after two seconds of being turned on? A fluke multimeter that powers up, LCD does it's self test and it turns on, but then fades to off after about three seconds and has a known good battery.
@mize_yir_bizz
Жыл бұрын
I have the same problem but mine did it only once and hasn't came back on. Change the battery, haven't changed the fuse, was going to try a resistor or diode.
@karthikkannan6753
3 жыл бұрын
Thanks brother !
@sgaws
4 ай бұрын
Mine has no display on screen. The battery is good. What do you think is the problem. How to test ?
@lamberatta11
9 ай бұрын
Would you know why the Fluke 87 might drain the 9 volt battery way to quickly
@SebastianSommerfeldt
4 ай бұрын
Hello, I have one question, my Fluke 85 is not working , i can see a mirrored 1 in first place, has anyone an idea what the fault could be? Thank your for your help.
@TheRealChuckNorris
Жыл бұрын
I want to get a decent multi meter but paying hundreds of dollars for one that's going to be used less than a few times a month isn't financially justifiable to me. What multimeter would you recommend?
@ijmeem7334
Жыл бұрын
Hello! The problem with my multimeter is - When I connect the DMM across a resistor (which was supposed to show a few millivolts), it shows a random voltage for a second and then gradually decreases to zero. That is, finally, it shows 0 volts. So, what could be the problem with my multimeter? Please share your experience. Thank you!
@cjaxed
8 ай бұрын
I used 3695, PeakTech multimeter. to measure electric rat traps. It was working, but then I activated dead voltage shok and while measuring turned to other parameters and my bultimeter made strage buzz sound and turned off. Fuse is ok, but multimeter is not working. Batteries are also good. Is it possible and how to fixit? :D
@gabrielconstantine7384
Жыл бұрын
My MM's ohms setting jumps all over the place when testing a resistor, everything else works ok, thoughts?
@eespino1
Жыл бұрын
HI THERE, DO YOU KNOW WHERE CAN I GET THE FLUKE 88 TOP SHIELD?
@FellDestroyedMusic
6 ай бұрын
When testing continuity, both leads connected together read 750 on the multimeter. Shouldnt it read 0? I am at a loss :')
@eltorobaka
2 жыл бұрын
My fluke 115 battery is leaking,it can damage the semiconductor in the circuot board??
@bennieshelter4366
2 жыл бұрын
I have a craftsman multimeter almost new ... everything works except for the continuity .... how would you go about to fix that ... the battery tests 9.4 volts
@dzhamza6495
5 ай бұрын
thank u so much . i will make u laugh .i found the wire not connected well hahahahaha just when i pushed the wire it work
@osamagamal-hf9ri
2 жыл бұрын
can you make a video about how to make a multimeter ? because i want to make a multimeter , but maximum voltage 100000 volts and current 1000 amperes .
@maxviews4446
2 жыл бұрын
Hello brother, as i see your subscribers are only 100 plus yet.. And KZitem runs ads on your videos.. How is it possible? How did you get KZitem montization..
@manoj.d_423
3 жыл бұрын
I have klein tools multimeter, the issue is its coming on, i am able to switch between functions but when testing for voltage or continuity nothing happens on the display. Besides the it being the leads are there any other issues that i can check?
@squirrel1179
Жыл бұрын
My multimeter does not zero after taking leads off battery being tested what could cause the this? I have to turn it off and back on to get the voltage to drop. Also the voltage that I am reading dose not make sense.
@larrybruner1408
2 жыл бұрын
My Fluke T5-600 reads voltage low. The bad batteries have been replaced, no change.
@rgruenhaus
3 ай бұрын
Looks like my Beckman multimeter
@stockstnt8
27 күн бұрын
Question ANYONE.. 2 METERS WENT OUT after checking a welder.. I have never even blown a fuse in a meter my whole life and a welder ad some sparks on one area I put a meter on it to read it and it just went blank and no fuse burned they are all still good .. WHY???? NO IDEA?? Just went out and now meters are dead nether blew a fuse I have had they on high voltage coming in building with no issue and check ing a somple single phase 480 welder it just ruined meter. Anyone know why or any way to repair them ??
@Johnod100
Жыл бұрын
are all multimeters soppose to beep i have a workzone one it does not beep
@TrainHer
2 ай бұрын
No sound on mine
@dnantis
Жыл бұрын
Mine does not stay put on 0.00 when on ohms reading setting !! Its a Radio Shack 22-812
@muhammedsaeed.m2392
3 жыл бұрын
Sir my fluke 87 iii housing is broken can u help me to get new one and it's display have black spots
@waynemeeks175
2 жыл бұрын
What could happen if you check ohms with power in the circuit?
@TrainHer
2 ай бұрын
Put mine there where I use it most 1.5 9 VT OL out of LOVE
@allenusucstroker1977
Ай бұрын
The video was that for all multimeters is just the flukes
@user-kd4ip6dy8c
Жыл бұрын
how can I fix multimeter damege over high frequency
@st6795
7 ай бұрын
My 117 is not beeping and my leads are good.
@umairbinriasat3281
3 жыл бұрын
Bro need your support to check my fluke 77 iv which is not reading mA even i changed fuses an clean the connections.
@colinevans7134
2 жыл бұрын
The multimeter should tell you low voltage battery come on the screen when in use, not used for a long time and don't turn on , first thing you do his check the battery and connector, ps not nock in you at all but if I wasn't using this great tool , take the battery out from any battery leaks. Puka tool to mess up
@SirFency
2 жыл бұрын
My Fluke is not measuring resistance properly. It slowly counts down until it finally beeps. I have changed the leads with brand new ones. Why would the resistance reading start at a high number then count down slowly till it reaches a low enough resistance to beep?
@dnantis
Жыл бұрын
My Radio Shack does the same !! Seems this User don't fellow our comments or don't know much about this YT scene !
@TheRainHarvester
5 ай бұрын
Bad capacitor?
@adolg4049
3 ай бұрын
I just have 1 prob at 20v Reads only 1 but at 200v reads normal
@osamagamal-hf9ri
2 жыл бұрын
if the multimeter not make any voltage so maybe the proplem in test leades or multimeter .
@صالحرمضان-غ8ز
Жыл бұрын
pls help my avo pins mixed up when i opened it unproperly and i want them back .its Dt5802
@mandydoncansil9606
2 жыл бұрын
Hi sir when I put 9v in multimeter its open and beep and died when I put 3.7v its open like normal
@looloopo2449
10 ай бұрын
Hi i connect to 15v battery to multimeter and after sometimes multimeter off😅 how can i turn on can any buddy tell me
@normanparker2103
9 ай бұрын
My test meter works fine, but it just won’t test capacitors What shell? I do I just keep getting the same thing 40.00 no matter what size capacitor are use
@cowoganteng3776
11 ай бұрын
👍👍👍
@bobloblaw7879
2 ай бұрын
thanks for the video, but a dislike for the annoying music.
@atifzameer8387
3 жыл бұрын
Dear friends I need to repair hioki 3256-50 digital hitester multimeter
@kidcurry1957
9 ай бұрын
83III Meter light won't work...
@marioc5277
2 жыл бұрын
If a Technician can't troubleshoot these problem on his own multimeter, what is he doing with a multimeter in first place ?
@flyback_driver
Жыл бұрын
Measuring voltages, resistance, checking for continuity, and/or measuring current consumption. Everything a multimeter does.
@gabrielshirk
2 жыл бұрын
My speaker beeps without leads in
@gaurishankarchandra9479
Жыл бұрын
Fluke 87v bAEE fault a raha hai
@M3a9m
3 жыл бұрын
but, what was the problem?
@gaurishankarchandra9479
Жыл бұрын
Help me
@markgrabowski8662
Жыл бұрын
so trivial, no answer to my problem
@javierrodriguez6877
Жыл бұрын
Hi. I have a fluke 77 that sounds when I select the continuity function with not leads connected. I checked and I found this part broken drive.google.com/drive/folders/1IYKnqIpnDW1cQxQynd608evI36eL2aOf?usp=drive_link Do you know what part it is?
Пікірлер: 81