Simple Step by Step process to remove cylinder head and replace o-rings on a Ducati 2 valve engine without a cylinder head gasket. This video also shows how to remove and replace the cam timing belt and how to tension the timing belt for the 2 valve Ducati twins. A dry compression test and a wet compression test are also performed.
To Get the Job Done:
Click-Type Torque Wrench: amzn.to/3amnqtg
Ducati Torque Wrench Tool 15mm: amzn.to/3gyyWmJ
Ducati Torque Wrench Tool (Set of 2 - 14mm & 15mm): amzn.to/33bgEmR
HEX Socket Set (Includes 10mm needed): amzn.to/30RLdhJ
Hex T-Wrench Set: amzn.to/2Y1bGHI
Permatex medium Thread Lock: amzn.to/2EFwtKa
Loctite Blue Thread Lock: amzn.to/2QA9mDf
Motorcycle Stand Set: amzn.to/3jncpLo
Compression Tester: amzn.to/31CdSrj
Ducati OEM Cylinder Head o-ring (High Pressure): amzn.to/3gBOdDh
Ducati OEM Cylinder head o-ring Set of 2 (Low Pressure): ebay.to/2Zc5FZ5
PROTECTIVE GEAR:
-Face Masks: amzn.to/3D0zCiW
-Safety Goggles: amzn.to/3fZQfNq
-Safety Goggles (2-Pack): amzn.to/2PX2eR5
-Ear Protection Ear Muffs: amzn.to/3QOBMrq
-Ear Plugs: amzn.to/3CZJHfR
-Shop Gloves: amzn.to/3aGzAgV
-Nitrile Gloves (6-mil): amzn.to/3awjyWQ
Video Index:
0:07 What the o-rings Look Like
0:14 What the Leak Looks Like
0:21 Oil Distribution for the Cylinder head
0:44 What Has to be Done
1:15 Putting the Bike Into 6th gear
1:34 Rotate Engine with Rear Wheel
1:36 Remove Pulley Covers
1:52 How To Check Timing belt Tension
2:02 Marking the Belt to the Pulleys
2:14 Lock the Rear Wheel in Position to Prevent engine Rotation
2:18 Remove Air Filters
2:25 Remove Carburetors
2:43 Remove Vacuum line For Fuel Cut-off
2:46 Remove oil Cooler
3:00 Loosen Lower Exhaust Manifold
3:30 Remove Timing Belt
3:47 Loosen the Cylinder Head Nuts
4:40 Remove the Cylinder Head
5:00 The Culprit O-Ring
5:25 A Close up Look at the O-Rings
5:42 Putting the New O-Rings On
6:07 A Look At the Cylinder Head
6:21 Installing the Cylinder head
7:23 How To Torque The Cylinder Head
8:53 Install Oil Cooler
9:08 Tighten Exhaust manifold Ring Nut
9:30 Install Carburetors
9:48 Install Timing Belt
10:16 Tension the Timing Belt
10:48 Install Timing Belt Pulley Covers and connect Oil Pressure Sensor
11:16 Tighten Exhaust manifold Clamp Bolts
11:26 Rotate Engine to Check for Interference
11:50 Dry Compression Test
12:06 Wet Compression Test
12:45 Air Filters Back On Fuel Back On
12:50 Start the Engine
13:05 Inspection After 15 Miles
13:17 Inspection After 600 Mile 3rd Torque Stage
→ Become a ScubaMoto Subscriber - goo.gl/iAwSQc
→ If this video helped, please give a thumbs up and subscribe for future videos
→ As an Amazon Associate I earn from qualifying purchases at no extra cost to you. Win!
→ Business Inquiries email: scubamoto@outlook.com
→ Support this channel - goo.gl/iAwSQc
#ducati #ducaticylinderhead
Негізгі бет How To Fix Ducati Cylinder Head Oil Leak O-Ring Replacement
Пікірлер: 75