So glad you made this video! Thank you man. I'm going to be building a gear drive pressure washer here in the states and I'll definitely be using this video for reference.
@envirocleansydney
5 жыл бұрын
I watched a later video of you doing this, amazing to see how much you'd taught yourself
@WashRite
4 жыл бұрын
Norwest EnviroClean thanks mate
@KM-gh3ob
3 жыл бұрын
Thanks for the video simple concise to the point 👍🏾
@scottspooner6070
6 жыл бұрын
This is the best way to get a longer life from your pressure washer pump. Nice work, thank you...
@WashRite
5 жыл бұрын
Thanks mate appreciate the support
@Gutterdogs
5 жыл бұрын
Thank You for this video.
@Carguy0882
5 жыл бұрын
Troy I have a 5hp 160cc ohv vertical Honda motor that I purchased. Would you happen to know what size bolts go in the bottom to mount a pressure washer pump it did not come with the bolts. Thanks alot. I have searched everywhere
@elomeli211
3 жыл бұрын
I have a simpson 420cc 4gpm pressure washer, basically the same motor as the gx390. Can I do this 5.5gpm upgrade?
@akun10years10
Жыл бұрын
Thank you for sharing this
@WashRite
Жыл бұрын
No problem 😊
@ownerproprietor893
4 жыл бұрын
Wow what a great video. Any chance of a quick point by point description? What size pump and gearbox is that? Would that same setup suit a Honda GX690? Any suppliers in oz?
@WashRite
4 жыл бұрын
The pumps are RW5530 and the reduction box is a PA2.1 reduction box, Yes it would work on a GX 690 and you can by all that from BAR group, without a doubt aussie biggest seller of everything water blasters www.bargroup.net.au
@srdjannakalamic5856
3 жыл бұрын
Thank you very much for the video.. I have a gx 390 Motor with A TS 2021 general pump 5.5 gallons a minute. Which gearbox do you recommend Ygr 1000 Zgr 1000 Ygr 1000P Thank you sir
@WashRite
3 жыл бұрын
i would try www.bep.kiwi/shop/item.aspx/gear-box-21-11-18hp-1in-5/11325/
@arthurthomas6852
3 жыл бұрын
Thank you for sharing. What manufacturer/ part number would be the reduction gear box?
@ericschermerhorn9266
4 ай бұрын
Any answer yet?
@manwiththeplan7143
3 жыл бұрын
How do i know what pump fits a gx390?
@rcrbrewster7840
Жыл бұрын
Would this setup work if you wanted the pump set up using a reduction box in opposite configuration with the same pump but with the pumps shaft on the left side instead of the right like the one u have here?
@WashRite
Жыл бұрын
yes it would
@pdrumz
5 жыл бұрын
could you put a higher psi pump unit on the GX390 if so how much higher you reckon. cheers
@WashRite
5 жыл бұрын
yes you could put a higher PSI pump on but to do that the pump would have to be less flow, for eg you can put a pump on that does 4000psi @ 4gpm
@englishozzie6703
6 жыл бұрын
Hey Troy i took your advise and just brought a 5.5 gpm machine. When u guys are applying your soap do you down stream inject or do you ise a x jet. Cheers mate. Steve.
@WashRite
6 жыл бұрын
always down stream mate, in my opinion the best way, no way you can xjet on big commercial jobs just a pain in the butt dragging a bucket of soap around with you, down stream is the way to go
@englishozzie6703
6 жыл бұрын
Wash Rite Limited. Cheers pal.
@brianbeauchemin7524
4 жыл бұрын
Hello sir question for ya I have a Honda gx390 with gear reduction and 5.5 gpm. What would be the psi to run that at. I’ve heard that combo isn’t safe to run at 3500psi. Is that true. The pump is a tss102.
@haroldpaulin9746
Жыл бұрын
What gear reduction that you have.whats the specific name?
@fensterputzernuernbergerlangen
4 жыл бұрын
Hi Thank you for the video .. how hard is it In your op... is it to change a crankshaft on a Honda GX390 ? thank you
@WashRite
4 жыл бұрын
Fensterreinigung Wintergartenreinigung it’s not worth it, time and cost would be easier to buy a new engine for $800
@fensterputzernuernbergerlangen
4 жыл бұрын
@@WashRite also when the Motor is 1 year old and a third of the price of a new one ? .. Thanky ou for your speedy Answer Wash rite ..
@WashRite
4 жыл бұрын
@@fensterputzernuernbergerlangen No problem always happy to answer / help when i can, feel free to follow us on FB or instagram if you have any questions i normally can answer faster there. Happy Easter by the way.
@brianochoa2627
3 жыл бұрын
What’s the over cost of this build?
@owlytv
Жыл бұрын
Just wondering what reduction box/gearbox model you use please?
@WashRite
Жыл бұрын
PA70.550.220
@shanebarrows1867
5 жыл бұрын
Hey i have a question, i seen in one of your videos where you said that you can increase the gpm on the pump using a gearbox reduction, so if i get a 4.5 gpm cat pump gearbox will it increase the gpm to maybe 5 or 5.5 gpm... Thank you
@WashRite
5 жыл бұрын
Hi Shane, A 4.5pgm pump will always max out at 4.5gpm, where the reduction box helps is when you run a pump like a 5.5pgm that buy the book should need at least 15hp to run that pump buy running a reduction box setup allows me to run that pup and get full flow but only on a 13hp honda, This means i can run GX390 and not have to run a GX620 or larger hence saving me $1000 plus on the purchase of the motor. Hope that helps
@shanebarrows1867
5 жыл бұрын
@@WashRite wow thanks man i really appreciate it... Love the videos by the way
@WashRite
5 жыл бұрын
@@shanebarrows1867 cheers mate, have a great day
@shanebarrows1867
5 жыл бұрын
@@WashRite Thank you, and I hope you do too.
@evanlucas8734
Жыл бұрын
@@WashRite does the same benefit occur when using a belt driven pressure washer
@shanebarrows1867
5 жыл бұрын
Hey i have one more question, i seen you said that you buy these pumps in bulk, and you said you sell them. Can you ship to the U.S and how much for everything (pump, gearbox, unloader, ect.) Everything i would need except for the motor, i already have a 670cc predator motor brand new. Thank you.
@WashRite
5 жыл бұрын
Hi Shane, Yep i could but to be honest shipping would make it expensive for you, I recommend you get hold of Rus Johnson from south side equipment and he would be able to supply everything and cheaper, Plus he stands buy his equipment so if something goes bad he is just a call away.
@shanebarrows1867
5 жыл бұрын
@@WashRite okay thank very much
@Brabyscastlewash
6 ай бұрын
So i have the honda gx390 i want to get this 5.5gpm pump and gear box i see rw5535 pump with reduction box is this the same
@WashRite
6 ай бұрын
this was a RW5530 pump but a RW5535 will work as well
@crispyeats7625
Жыл бұрын
Can you upgrade from 5.5gpm to larger 6gpm or more pump on the gx390? Or will you need to make changes to the actual engine? Thanks
@WashRite
Жыл бұрын
yes you can upgrade the pump and keep the 390 engine
@lunahouseexterior
Жыл бұрын
For the cost of psi/bar
@Wickedpissah092
4 ай бұрын
Hey bud, mine didn't come with bolts to mount the box to the engine. Do you know what size bolts you used to mount the reduction box to the gx390?
@WashRite
4 ай бұрын
M8/10-1.25,
@austicoptyltd7544
2 жыл бұрын
Handy video and my question is What pump did you use? my pressure cleaner is a Gerni 600P that I think was made by Nelfisk, the pump seems faulty and feels of replacing the pump, Nelfix has quoted crazy expensive so I guess I buy pump Myself and do as you have shown
@WashRite
2 жыл бұрын
That pump is a comet RW5530, You should be able to find a comparable pump at BarGroup just google them and they will be able to hook you up, if you need advise on installing it reach out troy@ritegroup.co.nz
@austicoptyltd7544
2 жыл бұрын
@@WashRite Thanks heaps mate
@darrenmanning4562
2 жыл бұрын
Hiya, can you please give the direct link to the 2.1 reduction kit, is it the Honda one on the page? Setting up to make the purchase this week unless you would recommend anything better that had come out. THANK YOU FOR THE VIDEO. #WASHON
Hi there can you give me the full spec of the comet pump and the gearbox reduction box drive. Thanks snd advance
@WashRite
Жыл бұрын
RW5530 pump, and the reduction box will be determined by the engine you are running
@manuscassidy3044
2 жыл бұрын
I'm doing the opposite to you and taking the pump off. But I cannot remove the reduction box, I've tried almost everything and I dint want to crack the cast alloy casing. Is there ant reason why it wouldn't come off easily?
@WashRite
2 жыл бұрын
because who ever put it on did not put grease on the shaft and the heat has fused it together, almost impossible to get off, I would try some heat from a blow touch cig lighter
@manuscassidy3044
2 жыл бұрын
@@WashRite thanks I'll try some heat
@bidyemsonisaac5658
3 жыл бұрын
I have a gx 160 6.5 can i put a pump like that on it
@sdfv4zx
9 ай бұрын
no
@user-bg5ty6ls2e
6 жыл бұрын
Where do you get your pumps and gearboxes from in nz
@WashRite
6 жыл бұрын
I import them in bulk myself, I can build you one if you want one
@user-bg5ty6ls2e
6 жыл бұрын
Wash Rite Limited i have a gx 390 but im running a ar direct pump. Would like a gearbox or belt drive and pump if you are selling them
@WashRite
6 жыл бұрын
yep can hook you up, send me an email when ur ready, troy@washrite.co.nz
@seky123
6 жыл бұрын
do you guys use soft washers or only pressure washers?
@WashRite
6 жыл бұрын
softwash rigs for roof washing, pressure washers for house washers
@seky123
6 жыл бұрын
but I have seen in your videos that you soft wash your houses??
@duartepaintinghandymanservices
5 жыл бұрын
so this pump is rated at 3000 psi with an output of 5.5gpm right? so what is the purpose of the of the reduction box?
@WashRite
5 жыл бұрын
Hi Jorge, to get peak performance out of the engine it MUST run at 3600 rpm or there abouts, most high flow pumps like this is designed to run around 1450rpm. So you need to reduce the rpm between the engine which runs at 3600rpm and the pump that runs at 1450rpm and that is what the reduction box does. Allows you to reduce rpm but keep 100% power and torque . Hope that helps
@duartepaintinghandymanservices
5 жыл бұрын
Wash Rite Limited great explanation, thank you!
@WashRite
5 жыл бұрын
Your welcome Jorge. Hope you have a great weekend
@themoreyouknow703
3 жыл бұрын
@@WashRite what gear box are you using I’m looking all over the internet for the right one and came across this video
@treshonrandolph2088
6 жыл бұрын
What oil does it use
@WashRite
5 жыл бұрын
LS90
@drainmonkeys385
5 жыл бұрын
Seems like you should have mounted that motor on a small skid,, and I would have put anti-seize on the key way and shaft..
@fensterputzernuernbergerlangen
4 жыл бұрын
You mean anti freeze what you put in your car for the window wipers ?
@bidyemsonisaac5658
3 жыл бұрын
How can i buy onlike that for a gx160 5.5
@sdfv4zx
9 ай бұрын
your engine is too small it wont work for 5.5 pump.
@stillwaterpressurewashing
6 жыл бұрын
which gearbox are you using?
@Mad-i134
6 жыл бұрын
Can anyone direct me on where to find a video on a Honda on how to assemble a water hose to the existing pressure washer? Want to use it for washing my driveway rather than using the existing 60 gallon tank wich I use for washing my personal vehicles.
@daewoooo5150
5 жыл бұрын
It’s a PA gearbox out of Italy.
@therustingmind1895
Жыл бұрын
Can you add a link or info on the pump you used.?
@WashRite
Жыл бұрын
The pump is a comet RW5530, you can get the from BE Pressure
@adamdavies8362
5 жыл бұрын
How much for one of these units shipped to Wellington Troy?
@WashRite
5 жыл бұрын
A complete truck?
@adamdavies8362
5 жыл бұрын
@@WashRite Nah, just this pressure washer unit with about 60m of hose and reel on a skid. I have a van that I'd like to mount it in. I have a tank already set up. Cheers
@WashRite
5 жыл бұрын
You would be looking around $5500
@adamdavies8362
5 жыл бұрын
@@WashRite cheers Troy, I'm looking at getting this sorted over the next 3 months or so, I'll keep you posted 👍
Honestly,,, Honda’s are great engines, but the predator is basically the same thing... I’ve seen that over time, they hold up just as well... so, a guy could switch over to a predator when building one and save almost half price on the motor... I’m considering that for myself
@randallowens271
5 жыл бұрын
that's what i did
@raymondj8768
3 жыл бұрын
engine assembly lube is not often used as anticize lmfao it will get hot n run off the part leaving no protection lol
@MrRjs803
5 жыл бұрын
That gearbox is going to have a leak from hell because of the o ring seal he forgot to put on the backside of the mounting plate that bolts to the pump!!!
@WashRite
5 жыл бұрын
Ryan Stevens hahaha no leaks thanks, pretty sure the o ring is on type of thing you remember when you build 60 in a year
@rasuldubhil3250
2 ай бұрын
390sayleshonche
@omkarkumarmahato9908
2 жыл бұрын
Contact namber chaiya hamko parts chaiya
@devinthompson1534
Жыл бұрын
Hey man thanks for the video, quick question is it cheaper to do this whole build yourself? Or if I bought a prebuilt already assembled with the gx390 is it similar in price. How much am I really saving if I decide to build my own?
@WashRite
Жыл бұрын
you will save huge money if you can build your own gear
@devinthompson1534
Жыл бұрын
@@WashRite okay, this is my first build I’ve settled on a gx390 and the comet you have I can order it right now. I just need to know what extra pieces do I have to buy to complete the build and to make sure I can hook up to my buffer tank. I used to work for a detailing company and I’m right in the middle of creating my own.
@devinthompson1534
Жыл бұрын
@@WashRite basically what other pieces do I need other than the pump and motor. Thanks for the quick responses.
@WashRite
Жыл бұрын
@@devinthompson1534 you will need an inline water filter to put between the buffer tank and pump, also need an unloader valve, as well as fittings like quick connects to connect hoses to the pump on the pressure side.
@devinthompson1534
Жыл бұрын
@@WashRite thank you sir! Very fast responses too. I’ll throw you sub.
Пікірлер: 105