I'd like to see all the commenters putting their 'experience' into video. The videos on this subject are limited yet there are a lot of critics and know-it-alls out there. PLEASE share your knowledge through video response not through a 10 second comment that helps no one except to serve as discouragement.
@danielmarsolais1562
4 жыл бұрын
You guys rock ! Thank you for sharing your knowledge .
@DaManDaMythDaLegnd
13 жыл бұрын
this will help a ton. Thanks. Excellent how-to video!
@stevefoley9448
8 жыл бұрын
Great job, clean and neat.
@TempoDrift1480
5 жыл бұрын
I need that silent hammer you're using so the neighbors aren't so inclined to see what's going on.
@yamanotakeshi
3 жыл бұрын
Thank you for uploading the video. It helps me to save money.
@mosesstone5916
9 жыл бұрын
very detailed, thanks!
@jsnthurst1
12 жыл бұрын
@STINGERNUTZ A drop of water on the rake metal will not touch the fascia, it falls vertically. However, there ought to be some space between the bottom of the face boards cladding bold so if water did get in there it would not be touching wood. A bead of Butyl rubber caulk on the corner seams would be a good idea to prevent wind blown water from entering. I'd also consider a 6 inch piece of flashing on the fascia corners, then the rake metal over that and then the fascia metal.
@Anavus
14 жыл бұрын
Very helpful. Thank you.
@thefutureofyesterday8136
8 жыл бұрын
When wrapping door, eaves, facials and corner trim pieces with metal. Is a absolute must to have a bender machine? If not then could some people respond with ways to get the bends neat and flush?
@cmz46
9 жыл бұрын
I watched this, and I noticed he did something that could possibly cause damage to your house. He mentioned don't install fascia from top to bottom so water runs. But that is exactly what he did. If that was on a roof the water would run right behind the front fascia and ruin those boards.
@user-tp2ks4ts2i
5 жыл бұрын
Exactly.
@davidlarson1369
Жыл бұрын
You want bottom up? So whwn you walk it up you stack over not under.
@otisp.driftwood76
10 жыл бұрын
Outstanding instructional video. What length and type of nails do you use....stainless steel, galvanized, etc?
@TrimBender
13 жыл бұрын
Thanks! I use .019 gauge for all the aluminum trim.
@seanykinskywalker2670
9 жыл бұрын
I use a hand brake for bending around corners, but what you did looked fantastic ... Question.... When you hang a long piece of fascia on an old house, do you start in the middle to nail it on? and work your way out?
@chadchristensen8419
10 жыл бұрын
Thanks for great video!...Checked out your website and dont see any video's on how to do the top of the peak on the gable end-where the two pieces come together....looks like a tricky spot. Also, I have seen the fascia pieces face nailed with matching colored trim nails (instead of nailing them on the bottom).....I think its so the edge of the new sofit doesn't get crushed (?).
@jungoogie
8 жыл бұрын
You know an easier way to get a decent bend on your metal, that I've learned, is to take my snips and cut into just a little bit of where I'm bending and then take out my handy Fairmont tongs and use that bend the metal. The little snip cut helps force the metal to bend how you want and the fairmonts are a god send paint brush of the tinner ways. Also start from the bottom up because of water flow. He says that but you can see he puts the bottom fascia on last which means water can flow into it.
@jianping5976
3 жыл бұрын
if we bend the corner like this, what if the rain runs through?
@PagingDrSwiss
3 ай бұрын
Beautiful!!!!!
@patriciaacreman909
3 жыл бұрын
Do the flashing prevent waves in the fascia
@philipzanoni
Жыл бұрын
I need a video with the same process but the aluminum piece is a 3 step bend to cover the crown moulding that's on the fascia. How does that work?
@Bean007PEI
13 жыл бұрын
I am no construction expert but wouldnt you put the front fascia on first and bend the corners around then let the sides over lap the front part . Looks to me the way you did it allows water to run down the side and under the front.
@bonanzahomer7512
6 жыл бұрын
Brian Williams yes 👍
@nikitagold5
4 жыл бұрын
Absolutely
@joannjeanette8171
3 жыл бұрын
And how is it no one uses sil trim for aluminum fascia
@rockdalejohn
5 жыл бұрын
You should have mentioned to use white aluminum nails. I use a sharp punch to make a small hole in the aluminum so the nails won't bend...
@ryanjapp
2 жыл бұрын
3/16 pilot holes help when using white nails to prevent buckling over a span
@malikgarrett2036
5 ай бұрын
What size nails or nailer should I use
@RiffRife
11 жыл бұрын
It depends on the quality of the carpentry or how strait the fascia board is. My opinion is if the face is over 6 inches, its good to have a rib (manual or brake buddy) rib to help with any issues with rippiles due to heat.
@CoolIHandIMatt
8 ай бұрын
Ok its an old video but what about the big gap where the gable end rake meets the eaves??
@jetshull
10 жыл бұрын
so you can just put eavestrough over it now?
@piddler51
12 жыл бұрын
Shingles will basically hold it in place??? Are you saying just slide it under the starter strip/first row and expect that to hold it?
@normssti3661
3 жыл бұрын
Dont listen to this fool you screw under the drip edge and like 2 screw in the soffit.. the guy in the video installed a facia with no soffit
@robertdiamondoil2384
7 жыл бұрын
Who sells this product ?
@DOLRED
13 жыл бұрын
Thanks...
@jessetrujillo
14 жыл бұрын
Thanks.
@roby14
8 жыл бұрын
Is there any way to bend the aluminum without a metal brake? Thx
@howardlovecraft750
4 жыл бұрын
Check out This Old House they have a video on KZitem.
@gregl2249
8 жыл бұрын
do u have on building the bird box?
@ggaazzlleegg
10 жыл бұрын
Get a pair of hand benders dude, if not you need to lightly score the bend with a blade and use a speed square to get a clean bend. And never install a piece of trim coil with only one bend in it, it will ripple as soon as the temp changes 5 degrees.
@canadianrooster6598
9 ай бұрын
No soffits???
@M107SASR
12 жыл бұрын
WOW
@denni98
4 жыл бұрын
Where can I buy white prepainted aluminium fascia ????
@jerraleebunnie6431
4 жыл бұрын
Dennis Williams Home Depot, Lowe’s, Rona or basically any building Center
@anacondasquezze4948
10 жыл бұрын
That "Dripedge" does NOT have the actual drip edge.
@ConsiderTheRavens77
5 жыл бұрын
90 degree drip is an absolute fail.
@hobbystock14
10 жыл бұрын
I'm pretty sure this guy made this video as A sales tool against his competition, Because no one uses flat fascia anymore. I personally put an 1 1/4 Fairdale and build my drip edge into the fascia.
@sleepinglioness5754
7 жыл бұрын
can you use a jigsaw to cut this aluminum?
@limogesfarmer6326
7 жыл бұрын
No - use a good pair of tin snips. Using a jigsaw to cut sheet tin results in the worst possible cut.
@jamesprestinario1567
7 жыл бұрын
Sleeping Lioness
@zzz7zzz9
2 жыл бұрын
You can, but it'll look like shit and pretty much destroy the fascia. I guess it all depends on what look you are going for.
@sleepinglioness5754
2 жыл бұрын
@@zzz7zzz9 I don't remember what I was working on when I asked this question, so hopefully, whatever it was....it worked! Thanks for tip.
@CougarLand
7 жыл бұрын
4:20 Correct, except that's not what gets done as far as the fascia board is concerned. The fascia board is actually the "bottom" of the whole project. So the only sure method is to have a third piece of metal involved that goes on first wrapping around the corners and then the fascia can be done as you are doing. If anyone knows of such a pre-made corner piece, shout it out. Otherwise that would make a great invention. Or you could just stick a few small pieces of ice and water shield around the boards first and call it a day.
@pattywaktdiy4175
5 жыл бұрын
Why put the drip edge on before the fascia? Wouldn't it be easier to do fascia first and then the drip after that? Thanks for the video.
@jerraleebunnie6431
4 жыл бұрын
J4543 P drip edge is usually on the eaves already if the roof has been shingled
@zzz7zzz9
2 жыл бұрын
No, because with the drip edge on first, you tuck the fascia up under it and it holds it in place.
@TexasCCRN
10 жыл бұрын
Hey nice video. Horrible lighting. Would like to have seen the actual "tabs" better. Tip: hold the piece still then count 1-one thousand 2-two thousand, 3, slowly will prevent the haze and give decent time to see emphasis on your great work. Thanks again!!!
@rayherrera6423
5 жыл бұрын
Ok dont you go the other way around ...
@AdobeRose1
4 жыл бұрын
does it make any sense to cover old wood with some rotting with the aluminum fascia? I can't afford to have it all removed and built then to add the aluminum for extra protection. Don't laugh. This is a poor person's hopeful fix-it....
@nikitagold5
4 жыл бұрын
Hey man, if the flashing prevents further rotting than by all means. Poor man's fix is better than letting the wood rot further
@zzz7zzz9
2 жыл бұрын
Absolutely.
@cpm324
11 жыл бұрын
Garbage! That gable fascia without a crown bend on it, will look like shit as so as the sun hits it, The drip edge is a joke, thats nothing but an "L" bend not going to work. There is alot of poor work going on and this is a good example of it.
Пікірлер: 66