Can't wait to have these guys swap out my Ultrex with a new Garmin Force and a couple 122sv's, as well as a LVS32 on my new ZXR21.
@josephcushman454
4 жыл бұрын
Zip ties are not to be used to tie to the trolling motor , need to leave fuse out until all power is connected to components .
@markchalmers499
2 жыл бұрын
You should always have your fuse as close to the power source as possible or you run the risk of burning that wire before the fuse.
@jamesvircik2865
2 ай бұрын
Thank you short and sweet show the exact size connectors and battery connectors. 10 gauge connector waterproof, 5/16 battery connector
@ZB32
Ай бұрын
Do you hook the graph to a power switch then the battery or straight to the battery?
@gmoore368
Жыл бұрын
You put zip ties on the shaft what happens when you raise the shaft for trolling motor?
@als3527
3 жыл бұрын
Watch all your videos, but I have question this one. 16 ga wire? Have you checked the voltage drop? 16 ga wire to power the lvs32 black box?
@franciscogutierrez6920
2 жыл бұрын
Doesn’t Garmin recommend not using zip ties?
@shawnphillips4772
3 жыл бұрын
Like to see trolling motor turn with cable like that
@DT-yl6yb
Ай бұрын
i am most concerned that you loose trhe ability to shorten the shaft when you enter shallower water.
@marvin41ful
3 жыл бұрын
Can you use the existing wiring (power) that was for an older unit?
@TedSnowVideo
4 жыл бұрын
I know this is an older video....but aren't you supposed to use at least 10 ga wire for power....preferably 8 ga. 16 ga speaker wire is pretty small for power connection especially at the front of the boat. Just curious.
@jmonson21
4 жыл бұрын
According to Garmin you may use 16 ga or larger to power the Garmin ECHOMAP Ultra. However, you do need at least 10 ga for the Garmin LiveScope if the extension wire is no longer 15ft, if longer than 15ft but shorter than 23ft you need 8ga wire, anything over 23ft they recommend 6ga.
@TedSnowVideo
4 жыл бұрын
@@jmonson21 Thanks. I just opened mine up today and read about the Ultra 106 installation. Haven't opened up the box for the Livescope yet to look at the paperwork. Have been hearing all over about making sure to use at least 10 awg wire so was just curious.
@bobbarnhill8557
9 ай бұрын
Why would you run seperate wires from the battery to each unit. This doesn’t make much sense. Since the wires are connected at the same spot on the battery. Much better to run 6 or 8 Gauge wire from the battery to a positive and negative buss at the bow. This is much cleaner and accomplishes the same end result. This method also allows you to add more units in the future if needed.
@keithashley200
5 жыл бұрын
What about the ground hookup on the black box.
@steveking8548
4 жыл бұрын
The instalation manual says to connect this to the neg post of the cranking battery.
@michaelspanos269
4 жыл бұрын
what 16 gauge wire are you using?
@dajahvue
4 жыл бұрын
To bad these units trolling motor ducer aren't compatible with each other.
@JaredCarter84
4 жыл бұрын
On there website they say I don’t need the black box for the 126 ultra? Am I missing something
@Huntgolfride
4 жыл бұрын
Depends on which livescope/panoptix transducer you're using.
@NytronX
4 жыл бұрын
If you use the LVS12, you don't need black box. If you use the LVS32, you need the black box.
@michaelstover2874
4 жыл бұрын
Are you running your 2 wires to the motor batteries or trolling?
@steveking8548
4 жыл бұрын
Always install with connections to the cranking battery.
@Lbz_on_crack
4 жыл бұрын
anything that isn’t the trolling motor goes to the cranking battery
Пікірлер: 25