You made that sound so easy. I just wanna buy a 350 rip the oil pump out and put it back in thanks bud.
@TheGarageGoblin
3 ай бұрын
It is easy! Cars are just adult legos 😎
@robertwilson4400
7 ай бұрын
Finally, down to earth, straight to the point homemade garage with real talk! Thank you for this video you answered two days of searching KZitem in 7:39 now I can do what needs to be done on my old GMT400 and be back on the road. Thanks again.
@lukeskypwner278
Жыл бұрын
I don't even need to do this right now. You made this interesting to watch!
@TheGarageGoblin
Жыл бұрын
Thank you! I’m glad you enjoyed it!
@Texasmule
Жыл бұрын
Omg thank you bro. I just took off the pan and now I need to take off the pump and replace it with a brand new one
@TheGarageGoblin
Жыл бұрын
Glad I could help!
@Texasmule
Жыл бұрын
@@TheGarageGoblin would you know how many ft/lb. Of TQ the bolt needs?
@TheGarageGoblin
Жыл бұрын
@@Texasmule 60-70 Ft pound. I put 65 on here!
@Texasmule
Жыл бұрын
@@TheGarageGoblin thanks! Do you think I should change the old bolts for ARP On my connecting rods? I wanted to do main bolts too but my knowledge isn't that huge so I just left them alone.
@Jeremiah.1
Жыл бұрын
Excellent video very well explained
@chiliwhit747
Жыл бұрын
I would open my oil pump up 1st pack it will grease or valo. to make sure of prime. Very important....💯
@Schlipperschlopper
Жыл бұрын
Never use a Melling 55 (today made in China) oil pump! They break in parts, get a Moroso or Summit high flow pump! Better use a soft thin flat copper shim gasket between oil pump and main cap! You cant weld cast to steel....you need a clamp for securing the oil pump pickup to the body...can find it at Summit.
@Tricolor610
Жыл бұрын
Melling not so good …? I have a Stock ( New ) inside …. i have low oil pressure when the engine is hot …. Engine ( 383 is build 2015 ) … from first day … low oil pressure… hmmmmm, Greeting from Germany
@justatool
Ай бұрын
Missing the windage tray, and I'd never weld disimilar metal without the proper wire.
@Tricolor610
Жыл бұрын
Hehehe…, looks like easy …. when the engine is outside but my 383 engine is still in my IROC…😵💫., I can not remove the oil pan…. , engine out or remove the k -member ( I need a hp pump , have low oil pressure when the engine is hot ) ..,, Greeting from Germany
@robertlee6936
Жыл бұрын
Is there no o ring anywhere for the oil pump Bc I just did this about a month ago and I’m getting low pressure again but it goes up and down a lot and up when I slow down? I don’t remember seeing a o ring when I did it myself
@maldo72
Жыл бұрын
🙄🙄🙄🙄🙄 you need to measure not just push the pan down over it and then push it down whatever feels good .... tack welding does not always work because you are welding cast iron to steel
@Ceo8203
Жыл бұрын
Yes I'm sadistic 😂😂😂😂
@micheltremblay1667
Жыл бұрын
If the oil pick up is set to low,would that give you bad or low oil pressure?
@TheGarageGoblin
Жыл бұрын
Unlikely, unless the oil pickup is sucking up dirt / sludge in the bottom of the oil pan and causing a clog. That clog could move into the oil galleys of your engine and could be potentially catastrophic. If you’re having low oil pressure definitely may end up needing to clean out the engine.
Пікірлер: 24