I had the same problem, bought the install tool..😮 screen was installed in a minute!
@labeledespjl
2 ай бұрын
Great video guy! About to do this tomorrow.
@cali530marcos3
2 ай бұрын
Thanks, and good luck
@heathergrupp6525
2 жыл бұрын
I like that this vato dont edit all the mistakes that la vida loca throws his way. We all have the world try to break us down. Its not perfect. But Holy Creator sees us through.
@cali530marcos3
2 жыл бұрын
thanks
@wreckanchor
Жыл бұрын
Good video. One thing I use to double check I have at least 1/2 inch clearance between the oil pan and the pickup is to remove the drain plug and run a cheap bore scope camera in thru the drain hole so I can see the clearance. The scope cost like 30 bucks on Amazon and I use it for all sorts of stuff.
@cali530marcos3
Жыл бұрын
I need to buy me one, they come in handy
@2010Flboy
9 ай бұрын
Nice tech tip regarding time gear dots.
@LifeAsItWeKnow
Жыл бұрын
you have a excellent video here, plenty of light and I dont get dizzy from camera movement... very good.
@cali530marcos3
Жыл бұрын
Thanks, appreciate the support
@glennmanchester3666
Жыл бұрын
87 and up I believe is when the dipstick got moved to the passengers side and also the one piece rear ,main seal came into existence in lieu of the old two piece that always eventually leaks way worse and way sooner than the one piece one
@elray2446
4 ай бұрын
She's looking good!
@cali530marcos3
4 ай бұрын
Thanks
@taxman3035
2 жыл бұрын
you gotta love the dog
@cali530marcos3
2 жыл бұрын
Yea, he's always next to me when I'm working in the back yard
@JAVIERHernandez-vt2nx
2 жыл бұрын
Good job bro
@cali530marcos3
2 жыл бұрын
Thanks
@dennyr8492
Жыл бұрын
That's exactly what i say " REALLY" when i drop something that's not suppose to be dropped in .haha😂 or can't fine my wrench or socket i just put down a minute ago great video,
@cali530marcos3
Жыл бұрын
Seems to happen a lot to me, thanks on the support, I try to explain as much as I can without making the video too long
@dennyr8492
Жыл бұрын
So i got a question on your video on adjusting valve and pushrods. You put both dots away from each other facing up. For the Distributor to drop in. What so it will be sitting on number One cylinder on the compression side
@cali530marcos3
Жыл бұрын
@@dennyr8492 so first I do dot to dot so u can install the cam and timing chain and that gets all the valve train in sync, then u turn the dots away from each other so u can install the distributor and ur ready to fire it up, if u don’t u will be 180 degrees out and will just back fire when u go to start it
@dennyr8492
Жыл бұрын
@@cali530marcos3 so what cylinder will the rotor for the distributor be at ? I don't know if i do this wrong i set both dots together TDC then put the distributor rotor close to number one cylinder on the cap. Then if it's not firing right move the distributor till it fires.. sounds to me I'm off a little.i got Edelbrock aluminum heads and a Howard rattler cam in this 350 i don't want to ruin this motor
@cali530marcos3
Жыл бұрын
@@dennyr8492 on my cars I put the rotor between cylinder #1 and the thermostat housing
@earthbros6508
Жыл бұрын
Ahuevo! This video is helpful
@cali530marcos3
Жыл бұрын
Thanks, I tried to show most of it without making the video too long
@dgomes4464
2 жыл бұрын
With the dot on top you said the distributor is ready to go in, what position or cylinder? Do you have a video? Thank you.
@cali530marcos3
2 жыл бұрын
i do not have a video on that, but you point the rotor inside the distributer towards the #1 cylinder
@jameswelch7516
2 жыл бұрын
Is this the end of the bild or are going to finish up with intake and carb extra
@cali530marcos3
2 жыл бұрын
i have one more vid on painting it, but thats it for now until i install it and do the first start up
@Supper_dad3
3 ай бұрын
I noticed your oil pump shaft didn’t engage to the pump and most vids I see they fit snug mine is like yours is that normal?
@cali530marcos3
3 ай бұрын
It depends if u have the plastic connector one or the metal shaft like mine, if it’s plastic it’s snugg and clips together, if it’s metal it just slides over it
@josecavada3830
7 ай бұрын
👍
@cali530marcos3
7 ай бұрын
Thanks
@glennmanchester3666
Жыл бұрын
I just jumped in on this channel are you going to run a hei or a ,marine points distributor I've run both but of course prefer the hei
@cali530marcos3
Жыл бұрын
I’m using the marine distributor with an exterior coil
@jsolo7576
26 күн бұрын
What's so special about the marine points distributor?
@jsolo7576
26 күн бұрын
Ok. I just read a comment that says you're assembling a marine engine.
@TheMerm0311
Ай бұрын
What size are the 4 corner bolts for the oil pan?
@cali530marcos3
Ай бұрын
1/2 inch or 13mm
@glennmanchester3666
Жыл бұрын
Much better gasket kit anyway
@cali530marcos3
Жыл бұрын
Yea
@pennyraven1222
10 ай бұрын
I like you're pit bull. 4:33
@cali530marcos3
10 ай бұрын
Thanks, he’s 7 years old now and protects the hell out of my family
@lordsauto
Жыл бұрын
did u check crankshaft end clearance. didnt see u do it
@cali530marcos3
Жыл бұрын
Yea, just did it off camera
@lordsauto
Жыл бұрын
May I ask the process?
@fred1706
2 жыл бұрын
what grade of oil do you put
@cali530marcos3
2 жыл бұрын
I use 5w30 since everything in the engine is new
@JTsMechanicShop5748
2 жыл бұрын
Is that engine running yet
@cali530marcos3
2 жыл бұрын
Not yet, I just got done installing it in a 1987 Malibu ski boat, doing a video on installing all the accessories then imma do a first start up video
Пікірлер: 51