Sir, I have to say thank you so much for an excellent video you showed step-by-step how to put together the entire throttle cable. I’ve been looking for a video all day and yours explained it fantastic and you took your time. Thank you thank you thank you you should be the only one on KZitem, making videos for go kart and dirtbike engines
@thedashingpeanut
4 ай бұрын
Thanks man I realized after watching the video that I installed that grey piece upside down you saved me like 2 hours of tinkering tysm
@robfraser33
Жыл бұрын
Helped out a bunch. Thank you
@soggyridesmotorizedbicycle6258
Жыл бұрын
Not bad bro. I know how hard it is to work on something and hold it in focus at the same time. I could see what you were doing clearly. 👍
@icft6183
Жыл бұрын
Thanks man , it was not an easy task 🤣
@jamesdeer1910
6 ай бұрын
Thank you very much on the segment about installing a throttle cable. That's a 5 star plus bonus !
@walterwilliams5491
7 ай бұрын
Thank you! I actually needed to learn that
@jamessmith2157
7 ай бұрын
Thank you Sir, certainly helped me finish my project
@chinesecomics1596
9 ай бұрын
Thanks bro, this video just saved me a long day
@samsungisgood-___-4107
8 ай бұрын
Thanks for this video, man. I didn't know what I was doing, but this really helped me.
@jbl_lfm_by_Adrian_perales
Жыл бұрын
Good video been trying to find a video to show me how to replace throttle cable on cam am ds 70 and this helped. Thanks
@dominikz.1376
4 ай бұрын
Great video: looks like you got it! Expert!! Great video man
@adventureswiththeaveragejo315
8 ай бұрын
awesome video i liked and subscribed
@can_of_easystart
10 ай бұрын
Life saver man
@200sgames
10 ай бұрын
Thanks!
@Aalphashark
11 ай бұрын
Thank you.
@icft6183
Жыл бұрын
There's a little piece that goes on top of the carb that I didn't show in the video
@hitzGhTV
Жыл бұрын
Thanks very much... I didn't know there was a small point inside the carburator to match where the cable lock
@GDTractor
Ай бұрын
Very helpful .. EXACTLY what I needed ..... GD Tractor
@zebzweers9466
9 күн бұрын
I Just need to get the end that rond thing off but help
@mikeanthony8934
Ай бұрын
Hey, I put on a new throttle cable and bike wont start. I remember there being a clear plastic piece covering the cable on the carburetor end. Do u think that's the problem?
@epoxy1710
Ай бұрын
I tried to do this for 5 hours on my DT50MX before I found this video and fixed it after 3 minutes😂
@michelmullaney3641
5 ай бұрын
So listen I need a little help bro… I got a pwk 21mm and I need it to fit the 13mm 80cc port with a boot..anyone know what I can get to make this happen or work?
@albertmurturi
11 ай бұрын
Thnxxxxxzzzzzzz❤❤❤❤❤❤❤❤❤❤❤
@mookie_gaming8501
Жыл бұрын
Where can I buy a throttle kit for my 50 I have been looking and almost every one I buy does not have that spring and needle at the end where can I buy?
@icft6183
11 ай бұрын
Amazon
@icft6183
11 ай бұрын
I'll try to find a link to it for you
@mookie_gaming8501
11 ай бұрын
@@icft6183 thank you
@olivervanderbloomen7854
Жыл бұрын
I assembled like in the video but my dirt bike just low idles and doesn't have any power and then will just shut off. Any idea why this might be?
@exospizy7858
Жыл бұрын
Adjust your tic over screw
@darrenodonoghue
3 ай бұрын
What happens if you don’t slide it into the little groove
@dominikz.1376
4 ай бұрын
I tried this two years ago on a JAWA 50cc and it was a diarrhea mess. I assembled and disassembled it like four times and it simply WAS Not right. The throttle cable was like real loose and didn’t snap back after a twist. It was just an assAnine diahretic mess for me. MMmmmmmmmmmm, mmmmmmmmmm
@user-hx8ih1cs9e
3 ай бұрын
Same thing happened to me how do you fix it
@user-hx8ih1cs9e
3 ай бұрын
I had to rotate the part under the spring it wasn't aligned with the pin as showed in the beginning of the video I thought it was but I was aligning it with the wrong part
Пікірлер: 37