*Works great my **Latest.Bike** I have a bad knee so I still get exercise but the bike assists me. I am a big guy so I didn’t think it would go as fast but it works great.*
@Ikeman50
3 жыл бұрын
It's not a tutorial........A tutorial explains the process......this is just a video of a 48v battery
@wheelie_kel371
Жыл бұрын
Right
@zefur321
6 ай бұрын
@@wheelie_kel371+1
@user-hx9cl9qf2r
2 жыл бұрын
I like your great work And I ask you for a picture of a diagram of the wiring process, your kindness I am a beginner in assembling batteries And thank you
@ericklein5097
11 ай бұрын
WTF is up with this wiring diagram bullshit
@TechKnowCSS
2 жыл бұрын
NEVER HOOK UP THE BALANCE WIRES FOR THE BMS WHILE IT IS PLUGGED INTO THE BMS, ALWAYS TEST FOR CORRECT WIRING BEFORE YOU PLUG IT IN, OTHERWISE IF WRONG IT WILL DESTROY YOUR BMS.
@vallethomas8147
2 жыл бұрын
Brother great super explain
@vallethomas8147
2 жыл бұрын
Excellent job Bro
@ogdenxproject2554
2 жыл бұрын
hi, great video! I have a big problem, I have the same bms but when I plug the 14 pin port to the bms it gets in contact between the c-, p- and b-! I checked the wiring several times! Also it heats up a little, I tried again with a 2nd identical bms and the same
@ss4goku9695
Жыл бұрын
You have your balancing leads wired wrong,
@leang2157
24 күн бұрын
when you use it in full charged How long does the battery last?
@bach2458
Жыл бұрын
What would be a rough price estimate on the cost for someone starting out. Including a cheap spot welder and all materials?
@SRHH_offical
Жыл бұрын
for me it was about 120 great bri'ish pounds
@relectric720
2 жыл бұрын
Great video thankyou. What can of spot welder are you using.
@raymercado3650
2 жыл бұрын
Great job👍 can you clarify where charging -negative and +positive wires are soldered too? Thanks
@raymercado3650
2 жыл бұрын
I have a similar BMS but I’m unsure of the wiring it to the battery? Can you clarify where the charging - negative and +positive wires are soldered on the battery and BMS board? Thanks Ray
@carlhoneck3589
2 жыл бұрын
@@raymercado3650 normally the C- is your negative lead of your charging wire, my bms only utilizes negative connections so the positive wire for the load and for charging come off of the main positive of the battery. Hope that helps some.
@user-hr8sd5kb3j
27 күн бұрын
Giau DIY good day, how many kilometers can you drive on a single charge?
@glenchia5364
4 ай бұрын
May I how u choose the BMS for this 48V 10A Battery pack?
@Thefakisgoinon
2 жыл бұрын
Hello, great video,. Do you have a wiring diagram for the batteries? I would like to build one myself but I never seen a video actually provide the diagrams. Thank you.
@GiauDIY
2 жыл бұрын
diagram on bms
@santoshpatil44342
3 жыл бұрын
🙏 वारे भावा ए खाऊ महाराष्ट्रात मावा 😂😘😘 मस्त
@tech4green
3 ай бұрын
Nice work👌😍😍😍
@GiauDIY
3 ай бұрын
😁😁😁
@rasheed-ameen
2 жыл бұрын
Thank you. Can you explain the charging and what is the optimal charger?
@sandeepkudale9314
3 жыл бұрын
U shuld tell all components information if possible purchase links
@costabravaamine7262
Жыл бұрын
how does sapel get green scotch? adhesive tape? or ordered it do you have a link?
@Markymark.W
4 ай бұрын
I'm making the same battery but I'm insure how do you charge them ?
@augustineamara2194
Жыл бұрын
Hi dear I appreciate your work. I am also a solar engineer based in Serra Leon I have so much interest in your idea I have started making my own better bank but I have some challenges can you please help me.
@adihikmat6745
Жыл бұрын
Mau nanya pak . Sy rakit 13s 5p .kendala low d gas langsung protek dari bms gk kuat apa batre cel gk bagus y
@user-ef1bh2me4p
Жыл бұрын
я с тебя прям проорал чувак!!!! такого рукожопа я еще не видел!!!! развеселил так развеселил))))))))))))))))))
@hengchhun5617
9 ай бұрын
Which BMS do we use
@sultanafareen472
2 жыл бұрын
Fantastic
@GiauDIY
2 жыл бұрын
Thank
@daviddelatorreperez4
2 жыл бұрын
El bms nunca se instala conectado, tienes que retirar el conector y ya que hayas soldado los cables y después conectas el bms.
@garypotter5569
2 жыл бұрын
Thus is some badass tweaker video if nothin else
@isipbata4007
2 жыл бұрын
I think that is 13.3ah, not only 10ah, base to number of batteries..
@songfromthehearttv6110
Жыл бұрын
Sir may i know if the battery you are using is lifepo4 and what is the capacity of 1 cell??
@MagneticMessengerofOrion
6 ай бұрын
Wow
@robbierobbie4636
2 жыл бұрын
What the top speed and how many km its goes with that 10 ah? Am about to use the 8ah.
@robbierobbie4636
2 жыл бұрын
And how about up hill. Is it more power than the vrla battery?
@user-ml2sd1ht5n
Ай бұрын
How much expensive is it
@balloney2175
Жыл бұрын
like a silent movie
@saitejagurram1922
2 жыл бұрын
can you tell me what is the green color tape which is wrapped around batteries ?? Any link where to purchase them?
@RA-vm4vn
2 жыл бұрын
Insulated green shell paper
@woodscriatures5636
2 жыл бұрын
10 ahmps that make a low autonomi ? Cus i make one bike but have some like 25kg my batt have 13 ahmp low autonomi ?
@yairburbea9709
3 жыл бұрын
What welder is it?
@themoonlauncher5849
3 жыл бұрын
its called a spot welder (kind of dumb he put a heart on your comment but no reply)
@yairburbea9709
3 жыл бұрын
@@themoonlauncher5849 yeah ik what a spot welder is, I was asking for the model :)
@themoonlauncher5849
3 жыл бұрын
@@yairburbea9709 ohh im not sure
@hristotonev6854
3 жыл бұрын
Its a point welder
@themoonlauncher5849
3 жыл бұрын
@@hristotonev6854 the person already knows what it is, there just looking for the model
@88ElevenShop
3 жыл бұрын
Thật sự rất hay và bổ ích !
@enrgysolarandpowerinverter4379
2 жыл бұрын
Good evening, I made a 48 volt battery, but after a full charge it does not exceed 51 volts. What is the problem? Thank you, my friend. I follow you from Egypt
@nathank.gordon9352
2 жыл бұрын
One of the cells or series connections have failed, as your max voltage is out by exactly one series connection (3.6v/3.7v)
@enrgysolarandpowerinverter4379
2 жыл бұрын
@@nathank.gordon9352 Thank you for helping people
@anthony1113
2 жыл бұрын
Let’s start with a few questions…what batteries are you using and how do you have them configured?
@ChickenCluck
2 жыл бұрын
Yes usually this problem arise only if you using non branded cells...trusted cells are sanyo/lgmj1/Panasonic/Samsung ...only these 4 is trusted Trusted as in with good feedbacks..other brands are questionable...
@costabravaamine7262
Жыл бұрын
can you make me a wiring diagram for a 16sp4 60v please?
@andrewblade8857
Жыл бұрын
I made a 48v battery with top of the line 3100 mah cells. It was 6p 13s and I used a 40 amp bms. The wire I used was 10 gage on . Well when I put this battery in my Ebike and hit the throttle it discharges really fast up and down . When I take it out and check the voltage it’s is still around 53v . What the hell did I do wrong? If anyone knows please help
@gerbr1275
2 жыл бұрын
I have a 16s 8p pack .. which is a 60v 20ah system, the problem is, 5 of the groups of 8 cells only charge up to 3.5v and the other 11 groups charge to 4v ...is this a battery problem or a faulty BMS ?
@Bergwacht
2 жыл бұрын
An entire group of cells can only be charged as far as the weakest battery in this group. This culprit battery would then have to get hot when charging, so you can use a thermal imaging camera to see whether and which individual cells are broken. if none gets hot then maybe some fets in the bms have burned out. you may be able to find the hot cells by touching them, but that's harder than it sounds.
@mariuszkolodziejski5484
2 жыл бұрын
Hi everyone! What is the name of this thinks what you hold on hands - you heat these sticks to the battery? How you Call this ?
@ss4goku9695
Жыл бұрын
Spot welder
@emmanuelmanahan3866
3 жыл бұрын
I want to see the actual test drive
@hassenmohamod8134
Жыл бұрын
Good,48Dseia
@bnk28zfp
Жыл бұрын
can you please make a part list, thank you!!
@anasaldasuki509
Жыл бұрын
Beli tempat batrey 4x12 dimana nos, kasih linknya kak
@ericklein5097
11 ай бұрын
How many amps do you plan on pulling? You have one strip of nickel on the main positive.....so its gonna heat like a mofo past 15A...and those cells are going to take a beating if you run them at 15A
@marbellaco-livingco-workin116
2 жыл бұрын
can you make a video please how to use 20 bird scooters to make a solar battery ?
@joyshreeram1374
5 ай бұрын
Millage kit na da ga 250wt motor maya
@dlarej1343
2 жыл бұрын
Matanong lang po.. Diba mostly laman na battery na ebike yung 12v 20ah..?? Need nila 4pcs para mkabuo ng 48v.? Pano yung ampheres nun nasa 80amp. Na?
@RAMESHKUMARJAT-1
Ай бұрын
👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
@muhammadraziq8837
9 ай бұрын
What is the voltage of one cell؟
@kevindtimm
2 жыл бұрын
What spot welder is used? For others, what have you used ?
@LordDirus007
Жыл бұрын
I assume just soldering
@user-bu7fb6nn9k
2 жыл бұрын
Good good good
@valtersouzaribeiroribeiro9534
3 жыл бұрын
Good good
@ilovemyindiawatanmeraindia346
Жыл бұрын
48 volt 10000 image ki battery kaise banegi bhai yah to batao aap abhi kya Pardesi kitne rupaye ka
@Maxttor
2 жыл бұрын
I put batteries on a diferent arrangement
@chandyller6773
Жыл бұрын
Sir...if the extra battery is 48 Volt's and the stock battery is 42 Volt's, does it increase the stock speed? Thank you...
@ericklein5097
11 ай бұрын
Yes it can.
@david2881
2 жыл бұрын
What type of battery are you using? 3.7v 10ah..18650. To get 10ah battery do you have to use a 10ah rating on battery? Why not use 13s3p
@mariancosmin7987
Жыл бұрын
Baterii 10 amper 48 volți cât costa
@electrobd7824
3 жыл бұрын
tnx bro
@jinendrabalasuriya8035
3 ай бұрын
I cant understand what all these videos doing ......if you connect at least two batteries together in parallel then what is the meaning of a BMS
@Bergwacht
2 жыл бұрын
its the hell of work to build these batterys...
@ilovemyindiawatanmeraindia346
Жыл бұрын
Mujhe electronics koti ka hajar volt ka motor car battery battery banani hai
@pativinuya-tg2qb
Жыл бұрын
Sir nagassemble po ako ng 48v 20ah n battery nung ikabit ko sa 350 watts 12ah eh nagtitrip po namamatay ang motor.
@adrianonea8468
2 жыл бұрын
what is that green tape??
@pativinuya-tg2qb
Жыл бұрын
94 battery po ang ginamit ko tas bms n 40 by 20 ang charge at discharge
@MdParvez-dq6dq
3 жыл бұрын
How many Mah per cell?
@debrajdas5467
2 жыл бұрын
2500 mah
@poison1989
2 жыл бұрын
acho que usar isopor foi uma péssima ideia.
@activitysportshd7208
Жыл бұрын
I have a few questions as I am new to this business. These batteries are 3.7 v 2500mAh. Doesn't 48v 10000mah happen when we make 13 serial connections and 3 parallel connections? You used 4x13 batteries in total, I'm confused.
@Knebebelmeyer
Жыл бұрын
iam confused too....there a some curios things in this video!
@illumi1011
Жыл бұрын
13x 3.7V batteries in series will add up to 48.1V; then multiply the capacities with how many are in parallel, that's 4p, 2500(4) = 10000. :)
@Knebebelmeyer
Жыл бұрын
@@illumi1011 dude really?... a 13s battery has 54.6v fully charged! think about it again!
@illumi1011
Жыл бұрын
@@Knebebelmeyer to avoid confusion i think it's best to use the nominal voltage in computations regardless of the actual voltage when fully charged. you are correct, the 3.7V in 13s will yield around that much voltage fully charged. i think the confusing part is whether to use 3p or 4p; 4p will add up the Ah, not the voltages, i.e. 2500mAh+2500mAh+2500mAh+2500mAh=10000mAh. 3p will only get 7500mAh. :)
@Knebebelmeyer
Жыл бұрын
@@illumi1011 yes thats true... why the guy in the video use the batteries like this, is his own mystic!! but there are 3.7 and 3.6V batteries outhere and both are the same! i know, its not the same, but it is! most people went for fully charged batterys, cause this is the value of most chargers! Voltage on Lithium cells is pretty much useless! you cant read something about it.
@shivamdeshmukh1557
Жыл бұрын
Kitne mah ki battery hai
@ddneb
2 жыл бұрын
Can you at least type your replies not just Thumbs ups and hearts? We are asking you questions that needs to be answered. Oh my!
@antoniocasta3625
Жыл бұрын
Hola, quería información. He hecho un 13s 6p con las bms que se ven en tu video. Las baterías son todas nuevas. He probado la batería en el motor eléctrico y funciona. Funciona lento pero funciona. Era solo para probar. Luego he conectado la batería al cargador Liitokala 54v 2 ah y no carga. La pregunta es: puede ser el cargador o la bms? Actualmente tengo: un lifepo4 de 48v conectado al inversor solar y un cargador de plomo de 48v. Para cargar la batería, ¿puedo conectar el cargador de plomo o conectarlo al lifepo4? ¿alternativa? Gracias
@brandon_montero
10 ай бұрын
Es una de dos cosas, el cargador de las baterias esta descompuesto o las baterias estan fuera de carga eso quiero decir que las baterias tienen menos de 2.8v-3.0v casa una o la mayoria, si eso es el caso el bms no va a detectar la batteria. Tendrias que desarmar la batteria y rearmala cuando todas la baterias tengan la carga maxima de 4.2v
@antoniocasta3625
10 ай бұрын
@@brandon_montero Grazie amico. Feci proprio cosi.
@rj.chatarpura
Жыл бұрын
whats is Price
@kerala2263
2 жыл бұрын
How much one battery cell നൗ?
@technicalsabaa6055
3 жыл бұрын
18650 bettery you give me plz help me
@swisstoni2913
2 жыл бұрын
21700 or 18650 cells?
@GiauDIY
2 жыл бұрын
18650
@random_idRI
2 жыл бұрын
How to 60v
@stevekirn8017
Жыл бұрын
What’s the point of making this if you’re not going to explain to your audience what exactly you’re doing & explaining best practices with something dangerous like a battery pack build??? Seems pointless especially dealing with something that can be extremely dangerous
@skrock5531
2 жыл бұрын
Kitna amp ka bms use kiye h aap
@kng_507kng
2 ай бұрын
؟
@tomhunter8090
2 жыл бұрын
Too bad that he doesn't explain the steps as he goes along.
@dailynewupdate7527
2 жыл бұрын
BSM BUY LINK PLEASE
@skrock5531
2 жыл бұрын
Bms ka details bhejiye bro
@mohamedelaqaoui8898
8 ай бұрын
where is the schematic 😏
@swapnilshirsat8294
2 жыл бұрын
For sale peace rate
@ebike799
Жыл бұрын
I cant understand
@skrock5531
2 жыл бұрын
Help me
@milodimich16
Жыл бұрын
This is very poor video.What is most important, he doesn't show.Not important. He is showing.
@technicalsabaa6055
3 жыл бұрын
plz help me
@lanhinh5434
3 жыл бұрын
Xin link mua pin a
@GiauDIY
3 жыл бұрын
vào shopee tìn pin lisen là ra nha bạn
@gabrielomblero281
2 жыл бұрын
Hi, what do you use to charge this battery??
@ChickenCluck
2 жыл бұрын
A battery maker told me to only use max 3.2a best is 2A charger for 10.5ah....because it's only 10.5ah...if for 21ah...can go higher ah but not 5ah...unless it's the first 30-50%...battery is complicated...lol...they sell those automatic charger from 5A to 2 to 1A charging from 30%-100%
@nosom23
3 жыл бұрын
Поехали кататься мой мальчик
@shivamdeshmukh1557
Жыл бұрын
Habsi sale dhang se banaa video bhi samajh nahin a Raha
@miloraddimic1711
2 жыл бұрын
Only one person from hundreds who has a classes teach people to see proper way to do and not got killed.Cappitalist do not give a sheet abouts life of the people.This person shouldn't be allowed to show spot welding procedures.
@user-bb6xn1hz7y
Ай бұрын
It's not a tutorial........A tutorial explains the process......this is just a video of a 48v battery
Пікірлер: 135