Excellent. Piece of art. Simple and practical . Great explanation. Thank you
@TonyArms17842
3 жыл бұрын
Thanks for the advice, I followed your build and added my own mods and I have converted a wood stove to a very powerful heater for my garage.
@robertostermiller586
6 жыл бұрын
I like your delivery on this video. As a fabricator, you covered everything well!
@JerichoRally
2 жыл бұрын
Man I'm glad you made this follow-up video. Genius!!!
@BYprospector
2 жыл бұрын
Glad you like
@hjhenk422
7 ай бұрын
thank you for this great video
@JM-un6mk
4 жыл бұрын
Best one I’ve seen on here, by far! Thanks for your advice Kevin.
@avoidtheherd7066
2 жыл бұрын
Simplest, easiest design/build I've seen yet. Possible high-tech safety device for fuel cutoff. 120v normally-closed solenoid valve w/manual reset would shut off oil and keep it off if power went out then came back on.
@davidregal1241
3 жыл бұрын
I’m trying to make one for my pole barn garage. You did a great job explaining how to build it. Thank you
@mikeRadamz
6 жыл бұрын
Many thanks Kevin! I made a waste oil heater using an older round vertical stove and "The Rushing Oil/Air Delivery System". I use a thin stainless steel bowl because stainless steel heats up red hot in seconds, once the bowl glows, the oil vaporizes instantly and there is no smoke in a few minutes. For forced air, I use my air compressor since the heat is only on when I am using the shop.
@BYprospector
6 жыл бұрын
Awesome
@BarefootBeekeeper
5 жыл бұрын
I made a stove like this to heat a stone built hut back in the 1970s. I had no electricity, so couldn't add a fan, but it worked fine without one, just with the natural draught drawn up the chimney.
@codylay4341
8 жыл бұрын
thanks for posting this video! I just converted a barrel stove over today using most of your design.
@DimaProk
3 жыл бұрын
I like this build a lot and thanks for pointing out all the details. I think the flange is a great idea. If I was to improve on something it would be to replace the coleman fan with something else that's more quiet and efficient.
@BYprospector
2 жыл бұрын
I have the Coleman blower in a box with insulation to dampen the noise. I had the same blower for years. Just replaced it a few months ago. The trick is to break it in slowly and keep it cool.
@MrPajamaman40
5 жыл бұрын
Thanks for the great video teacher . Hopefully I'll be able to make my waste oil heater now .I love it. Awesome video 👍 thank you for taking the time
@curtishenshaw5592
8 жыл бұрын
Great video. Now I have to go find a wood stove to make one. Thanks for sharing !!!
@scottbuild-n-fix8868
8 жыл бұрын
Kevin, good explanation of your burner. I'd appreciate you taking a look at mine. Very similar principal for sure as far as getting the air to swirl. I'm very much still in the process but on the down hill side for sure. I appreciate your attention to detail and clean builds. I subscribed because your picture makes me smile.
@BYprospector
8 жыл бұрын
Scott Build-n-Fix Will do
@trmclaren
9 жыл бұрын
Thanks for info on these youtube videos Kevin Rushing . Going to be picking up a stove this weekend to turn it into a waste oil heater. Cant wait to work in the garage with heat.
@BYprospector
9 жыл бұрын
Can't wait to see a vid
@trmclaren
9 жыл бұрын
Will do good sir. Mines going to be a little different but you gave me a great idea and start.
@M107SASR
Жыл бұрын
Yup you answered my question do not leave it un attended in case the fan don't work thank you Kevin
@JOEZEP54
7 жыл бұрын
Good video, nice clear explanation. Thanks
@jontom6775
4 жыл бұрын
Great video. In Canada it's so darn expensive for heating. So much Government regulations. A little more money for the family instead of the government.
@victorvillablanca8668
4 жыл бұрын
You people of canada....can you help me with more information about this burner oil waste? My name is victor villablanca i live in Valdivia city on Chile....my email is villablancagatica@gmail.com and my celular phone is +56957262158
@tractorman4461
4 жыл бұрын
Good detail in the video. I like your disclaimer, which was a very good idea by the way. I've been thinking of a compressed air atomized mist kind of delivery, but the drip system seems to be bullet proof...at least as long as gravity remains a constant. Good job sir.
@BYprospector
4 жыл бұрын
Thanks for watching
@earthstewardude
5 жыл бұрын
solenoid valve connected to a thermostat which will stop the oil flow if flame goes out.
@1979cvx
4 жыл бұрын
Where can i find the valve and thermostat?
@twigglykevin
7 жыл бұрын
i left mine for 34 seconds and it exploded! great vid
@windstalker101
Жыл бұрын
So years ago, before the internet, I did this to a wood stove in my shop. It worked really well for quite a while. One day while it was running in my shop, I got distracted by an intruder on the property. about 45 minutes later when I got back. The entire stove and stove pipe were red hot. Glowing, almost white, and it was burning like a jet engine. Luckily I had a well casing as a stove pipe and it held up. It was insanely scary. My shop was all metal, there was nothing around it to burn and a concrete floor, It took it like 3 hours to burn down. I used up four fire extinguishers on it. They were useless. water would immediately flash to steam. not an option. going to build another one but it will have safety features. Be careful guys
@mikebond6328
Жыл бұрын
I had a similar experience. You’re right, once that oil gets hot it’s hard to put the fire out. I even shut off all access to air and it still continued to burn for quite awhile. It was explained to me that’s the reason for the feed pipes being inside the burn pan so that if the oil level gets too high it will choke off the air and kill the fire. I’m not sure it would work, especially with forced air.
@KeithBair
Жыл бұрын
At first it sounds contradictory, but adding oil to an oil fire can help cool it down and put it out. By mixing cold oil with the burning oil, it will cool down the burning oil and make it easier to extinguish when it gets closer to not being of a self igniting temp. Water on oil is a no go.
@windstalker101
Жыл бұрын
@@KeithBair Well you're right about one thing, it is counterintuitive, since I had oil running onto it continuously for 45 minutes. It doesn't seem like leaving it on would have solved the problem. Conversely, it would have run out of the stove and into my shop. As I said this is before the internet, I had never seen or heard of such a thing. I just sort of invented it. a total science experiment. Scared me so bad I never did it again. during this I got burned so bad I had to go to the ER. Oil spattered on me from the fire extinguishers. burning oil. after watching a bunch of videos about it I am going to try it again. Although with much caution.
@alexbetts8291
Жыл бұрын
Cheers bruv
@JodBronson
7 жыл бұрын
Hi, VERY NICE and thought-out design, simple but extremely fuctional for sure. As for safety, why don't you put an In-Line Solenoid (Before the Drip Control) to STOP the fuel at a certain Temperature? Use a Snap Disc and when the Temps reaches a certain point. The solenoid would CUT-OFF fuel line... That way your Stove would NEVER burn over the desired temps :))). So fire wouldn't be an issue if unattended or when you walk away or even forget even :D
@fordracer1415
4 жыл бұрын
Jordan Bronson I had a similar thought what cut off valve are you talking about I’m not familiar with snap disc I was thinking about a sprinkler valve that was controlled by a thermostat instead of timer
@rustyrobinson8027
Жыл бұрын
Thanks
@robertrobinson2649
7 жыл бұрын
Is it just me or does Kevin look like a skinny Larry the cable guy. : )
@sammalone7914
9 жыл бұрын
Thanks for the video. A+
@BYprospector
9 жыл бұрын
Thanks
@spark23ca
5 жыл бұрын
looks pretty cool ...could you give a ball park figure on how long the oil lasts ..gallons per hour or whatever ...i've looked at some of these and they are complicated ...you made it simple ..i got an old wood stove that cracked but i can weld and i got a skidder so i got lots of burnt oil and gear oil ..thanks again for posting
@BYprospector
5 жыл бұрын
There are a lot of factors but my stove uses about 5 gallons in 8 hours
@spark23ca
5 жыл бұрын
@@BYprospector awesome ..my garage is fairly well insulated ...its 5 degrees outside and in the garage with no heat is 40..its just big enough for one car and a few workbenches and other junk ..so i likely wouldn't have to run it very long ..thanks again ..this will save me some wood cutting for a little bit
@deigert1994
3 жыл бұрын
@James Short where can we find your video
@matthewmonsees8288
5 жыл бұрын
I finished building mine tonight and I am having trouble getting it to stay lit. The only difference from yours is that the burner assembly enters the stove at a 45 degree angle. I light out using a rag with about am 1/8 cup kerosene. It lights and when I turn the fan on it really takes off. But then it just slowly Peters out, so I'm pretty sure that I'm having trouble getting the oil to burn on its own. Once it went out before my paper was done burning so I got some smoke, but it had a good enough swirl that none of the smoke was exiting the door. So I'm sure it has good swirl. One thing that I have noticed is that it takes three turns to get the pencil lead thick flow going, and that takes forever to actually get the flow started at the bowl. My bucket is about 4 foot above the bowl. And I'm using used engine oil. Currently a warm 45 degrees out so it shouldn't be too thick. Any ideas or tips?
@BYprospector
5 жыл бұрын
Before you light make sure you have a pool of oil to burn
@earthstewardude
5 жыл бұрын
drain hole several inches above burn pot - secondary measure if flame goes out. oil will then escape out safety drain into secondary catch reservoir.
@lancerudy9934
5 жыл бұрын
Very nice
@thomasblack4217
2 жыл бұрын
How long does a gallon of oil heat for how many hours
@BYprospector
2 жыл бұрын
5 gallons lasts 8 to 10 hours roughly.
@thedavesofourlives1
Жыл бұрын
the phase angle dimmer might be problematic with an induction motor.
@BYprospector
11 ай бұрын
Haven’t had any problems with it
@jpjpk6320
6 жыл бұрын
In your opinion, whats the minimum and maximum cfm size blower that would work the most effectively. Many thanks, jp
@ESLinsider
2 жыл бұрын
Okay so I see you are mixing the oil with the air when it enters. So I am wondering if the air needs a fan? I've got a little tent stove like stove I made and hoping to get it to burn oil too.
@BYprospector
2 жыл бұрын
Watch the video i have of the oil heater made from a wood stove.
@cfitzgduke
Жыл бұрын
What is the fitting at the bucket so the oil does not leak out of buckett?
@BYprospector
Жыл бұрын
Yeah. It’s a quick disconnect fitting so I can fill the bucket with oil
@earthstewardude
5 жыл бұрын
There are a number of safety devices that one can install in order to be able leave the stove unattended.
@Majorme2
7 жыл бұрын
How much carbon build up do you get... I gave a similar set up but I gave to clean the bowl daily
@BYprospector
7 жыл бұрын
Hardly ever if you have enough air flow. Maybe once a week of continuous use
@idahodeerhunter
7 жыл бұрын
how would you compare the heat output to burning wood? real curious, i like the idea of this
@BYprospector
7 жыл бұрын
idahodeerhunter it can be much hotter but much easier to control.
@idahodeerhunter
7 жыл бұрын
Kevin Rushing interesting one more question, at the end of your video during the disclaimer you mentioned that if the blower loses power it could cause trouble maybe a fire. Was that sarcasm or not, logic tells me that if the forced air stops the oil will go out or am I not thinking correctly. Thank you
@BYprospector
7 жыл бұрын
idahodeerhunter the oil will still burn even if the blower stops. Because the blower helps with combustion, if it stoped, the oil could get in to an overflow situation with flames and all. Commercial models have sensors to stop the flow of oil if air or flame are lost.
@idahodeerhunter
7 жыл бұрын
Kevin Rushing makes sense thanks for the reply
@stonewallpi1
8 жыл бұрын
Excellent breakdown of your components! The "100 degree switch that turns your fan on when it gets hot enough". Do you have a name for that and where did you get it? I looked on Amazon with no luck. Thanks for the great information!
@BYprospector
8 жыл бұрын
It is a temperature switch found furnaces, air conditioners and other heating and cooling systems. It is a 100 or 120 degree F normally open switch. This switch closes at the rated temp allowing fan start. You can get it at most appliance or heating cooling specialists.
@stonewallpi1
8 жыл бұрын
Thanks for tracking down the info Kevin! Can't wait to start the build! :)
@jimshowtovideos
7 жыл бұрын
thanks a lot
@Eyenonothing812
9 жыл бұрын
How long would you say a 5 gallon bucket of oil last? Nice vid btw!
@BYprospector
9 жыл бұрын
I'm guessing about 8 hrs depending on the size of flame and Thank you
@earthstewardude
5 жыл бұрын
was that 3/8" copper tube? or 1/2 ...
@DLaing898
Жыл бұрын
Is your blower ac or dc? I tried wiring a dimmer switch at first then a fan controller to a 12v dc air pump with no luck
@BYprospector
Жыл бұрын
It is AC. Normal home lighting dimmer switches only work on AC. You would need to buy one rated for DC to use it on DC lights
@jeickholt17
6 жыл бұрын
Would you happen to have a link to the blower you have? Looking at getting one......thanks
@1979cvx
4 жыл бұрын
me too
@jpjpk6320
6 жыл бұрын
Kevin, still would like to know where and what model coleman blower u used. Still confused. Thanks
@BYprospector
6 жыл бұрын
JP Haynes I'm using one you can get at any Wal-Mart or sporting goods store. It's for inflating air mattresses.
@jeickholt17
6 жыл бұрын
Does the copper pipe HAVE to be inside the black pipe or can it run next to it?
@BYprospector
6 жыл бұрын
jeickholt17 Yes. Copper gets soft at lower temperatures and will also slab up causing it to plug. You'll be constantly unplugging it.
@jeickholt17
6 жыл бұрын
Kevin Rushing thanks for the reply. Im trying to figure out how to run my copper in the tube, but cant get it past the 90 degree bends
@BYprospector
6 жыл бұрын
jeickholt17 shouldn't be a 90 in the copper
@Laurel-Crowned
8 жыл бұрын
what would be the difference if I dripped the oil in before entering the heater?
@Laurel-Crowned
8 жыл бұрын
nice heater btw!
@BYprospector
8 жыл бұрын
Wind Storm I'm not sure what you mean
@Laurel-Crowned
8 жыл бұрын
+Kevin Rushing after seeing your second vid I see you put the oil drip line at the end of the flame. what would happen if I dripped the oil inline before entering the burn chamber?
@BYprospector
8 жыл бұрын
Wind Storm you could try but I think you'll get some oil splatter which would cause smoking. If it drips close to the end at the bottom of the air supply pipe it gets the oil out of the direct flow of air minimising splatter but is able to stay cool enough so that it doesn't slag up and plug. Hope that helps
@Laurel-Crowned
8 жыл бұрын
+Kevin Rushing thanks
@Ameer-lh2nf
8 жыл бұрын
Nice dog
@blixtkrig
9 жыл бұрын
how about putting some isolation it the roof :)
@jpk1a
6 жыл бұрын
Kevin, how big a hole did u drill in back of stove 3/4 inch?
@BYprospector
6 жыл бұрын
jp jpk that would work
@Ben-sv9op
7 ай бұрын
What is that bowl
@BYprospector
5 ай бұрын
A stainless steel bowl from walmart
@earthstewardude
5 жыл бұрын
okay... sorry - it's 3/8"... wish I could see the brass fitting close up.
@donstudnicka4998
7 жыл бұрын
Where can I buy that coleman blower?
@MegaMarclar
4 жыл бұрын
Any sporting goods store that sells camping stuff.. it is an air mattress pump.
@Majorme2
7 жыл бұрын
Are you burning waste engine oil.?. That’s my source.. btw dried up this week.. I’ll be moving to rocket mass heater next yr...
@BYprospector
7 жыл бұрын
I'm burning mostly transmission fluid
@johnpatterson6538
5 жыл бұрын
hi there its nearly 4 years down the line are you still using the heater did you ever add any safety cut off's etc to the heater? if so what did you fit? thanks john
@BYprospector
5 жыл бұрын
I haven't used it yet this year as I've been working out of town. The stove is the same as in the video except I added a metal oil can. Plastic is harder to seal. Still working well.
@juanluissandoval506
7 жыл бұрын
hello there whats the dimmer for?
@BYprospector
7 жыл бұрын
Juan Luis Sandoval it varies the speed of the blower
@427med
6 жыл бұрын
this is a copy of 1940,s Babbington burner been around forever
@Majorme2
7 жыл бұрын
Ok I understand.. I mix as much Trans fluid as I can... but now my foes is out with no source. Thanks
@BarefootBeekeeper
5 жыл бұрын
You have woodprix spammers.
@johntaylor9028
5 жыл бұрын
K koo
@Juriy61
9 жыл бұрын
kzitem.info/news/bejne/wJyEu5mbrHyJfYI Видео . У меня как то проще и надёжнее.Всё управляется .Yrii.
@johnrichardson9400
5 жыл бұрын
sorry but I don't think you should be making videos on things that are unsafe my friend. as there are so many people. who will make a stove without thinking of the dangers .. aj England;''''
@BYprospector
5 жыл бұрын
I totally agree. Don't make one
@EnvirotekCleaningSystems
5 жыл бұрын
@@BYprospector lol I just subscribed.
@johnrichardson9400
5 жыл бұрын
so wye do it . but there again there is a lot of crap in the uk . that as come from the usa
@bill14729
5 жыл бұрын
What about all the crap from the UK coming to the USA
@Oddone64
3 жыл бұрын
Yep, there’s always that special one ! 🤦🏻
@timidater4803
5 жыл бұрын
where did you get your temperature switch and needle valve?? Any info would help!!
Пікірлер: 122