Hi everyone - video timestamps as follows: 0:00 - Topic Introduction 01:15 - How to Model Curved Beams in the X-Y Axis in Revit Plan Views 04:13 - How to Model Curved Beams in the Vertical Z Axis in Revit Elevations and Sections 06:59 - How to Model Beam Systems to follow a Buildings Roof Curvature 11:09 - How to Attached Beams to Sloped Organic Roofs in Revit 15:15 - How to Model Curved beams across 3 Axis in Revit. Hope you find the video helpful. If you like this content please support 8020BIM by buying me a (much needed) coffee: www.buymeacoffee.com/8020BIM Niall
@andrewkd79
4 жыл бұрын
This has been one of the best instructional yet. Not completely relevant to me, but i can see the potential elsewhere. Thanks heaps.
@8020BIM
4 жыл бұрын
No problem Andrew, glad you found it potentially informative anyway! 😁 Niall
@benhadidikbal2820
4 жыл бұрын
Revit does not fail to surprise us, Thanks for your advice
@8020BIM
4 жыл бұрын
You are most welcome, glad you found the video informative. Regards Niall
@19marmot95
3 жыл бұрын
Wow... the last part was exactly what I needed... Thank you so much
@8020BIM
3 жыл бұрын
You are very welcome Marmot, glad you found what you needed. Niall
@larry6510
3 жыл бұрын
Thanks for the video, from Monterrey Mexico
@talosfranks1007
3 жыл бұрын
This video helped me so much for my final, thanks g👍🏽
@8020BIM
3 жыл бұрын
No problem Jordan. Glad it helped! Niall
@leben1841
4 жыл бұрын
Excellent as usual!
@8020BIM
4 жыл бұрын
Thanks for the feedback as ever 😊
@oluwatobilobaanjorin35
3 жыл бұрын
This video is very helpful. Thank you.
@8020BIM
3 жыл бұрын
Thanks for the feedback Tobi, glad you found the video informative. Niall
@solvedplus858
2 жыл бұрын
very cool
@luisfe7187
4 жыл бұрын
Thanks
@8020BIM
4 жыл бұрын
No problem Luisfe, glad ot help.
@luisfe7187
4 жыл бұрын
8020 BIM please can you teach us how to make this sterosttucture roof and stair ibb.co/B4n2TX6 ibb.co/BGG5tzR
@carepointglobal1356
3 жыл бұрын
Great video... I have 2 questions. 1- how would you put a corrugated sheet metal over the curved beam in the z axis? And 2- how do you you a a tapered column small at the bottom and wider on the top? If you could do a video that would be great
@8020BIM
3 жыл бұрын
Hi there, For corrugation I generally advise against modelling the corrugated materials. The triagnulation and sheer number of surfaces complete hinders the performance of large models and is what I would deem as "over modelling", in line with the various LOD standards (Level of detail/definition) from around the world. I would use a roof by extrusion with a suitable model surface pattern to represent the corrugation. I will put the tapered column on my tutorial "to do" list for sure. Thanks for the suggestion. Any additional queries at all please let me know. Niall
@beniaminbalint3711
2 жыл бұрын
How can you do a bolted connection at the curved beam/column interface ? Like in your first model. You don't want a haunch but you do want an endplate. Or how do you trim a curved beam to manually fit a skewed plate at its end? In revit i mean.
@AkunBelajar-bj7fv
Жыл бұрын
Great tutorials, but can u show us how to make connection between curved beam? Ive tried several times with generic costume connection and basic connection that in revit but always failed, it say "non linear element not supported"?
@ridwanfaqih9888
Жыл бұрын
yes, me too, i think revit can't connect between coloumn & curved steel beam
@affanshaikh3274
Жыл бұрын
I am trying to add second diary beam along the curved beam, but it’s adding the Secondary beam below the curved beam. Can anyone help me out?
@myfavadsreels.9025
3 жыл бұрын
Sir im still getting the beam on level 1 and level 2 not getting through along curved beam
@nicodm6273
4 жыл бұрын
I have Revit 2019 but I can't visualize the "Automatic Beam System" button. Why?
@8020BIM
4 жыл бұрын
Hi N - I am unsure why this might be the case if you followed the steps (should be immediately visible in the Structure Tab). If you can give me a bit more information I will try help you further. Niall
@nicodm6273
4 жыл бұрын
@@8020BIM Fortunately I solved the problem. Anyway thanks !
@8020BIM
4 жыл бұрын
@@nicodm6273 Great, all the best!
@robertorobertini6221
4 жыл бұрын
Excellent expanation.You are one of the best KZitem gurus except for one thing.Plz Plz stop waving your mouse pointer in all directions like U have Parkinsons Disease.It is so frustrating
@8020BIM
4 жыл бұрын
Hi Roberto. Thank you for the feedback, it's appreciated. I will work on the mouse movements, its a habit I am finding hard to break 😂
@matice7179
3 жыл бұрын
Hi, I cant click on this `3D constraints` button. Does anybody know how to fix this problem?
@8020BIM
3 жыл бұрын
Are you sure you don't mean 3D snapping Matice? You can see that in 3D views. Niall
@matice7179
3 жыл бұрын
@@8020BIM I ment the box under properties > constraints> 3D, that's checked. (But i can't see 3D snapping..) When I draw the outline of the Beamsystem, i don't see the little triangle "defined as slope". www.cadlinecommunity.co.uk/hc/en-us/articles/360000569269-Revit-2018-Create-Beams-Along-a-Curved-Roof ^ in that animation you will see that they also check that box, like you have. But ik can't, because it's greyed out.
@matice7179
3 жыл бұрын
Found the solution! I had to set the workplane to a level.
@8020BIM
3 жыл бұрын
@@matice7179 ah right, good to know. Well done, thanks for letting me know! All the best. Niall
Пікірлер: 39