Had this thing for years and I've done a lot wrong. This is very helpful
@ArtbyLexii
Жыл бұрын
This is great! I like that its short and right to the point but also very informational. Thank you!
@sunittas7053
8 күн бұрын
Thank you very much, this very informative and to the point!!! 🌟
@karissazenkner3964
5 жыл бұрын
This video is great! I made a training manual for an office that I worked at and linked this video in the manual for future assistants! I also still refer back to it myself!
@niravb.patelmdjdfacsfclm4232
2 жыл бұрын
Outstanding operational video - we watch it each and every month that we perform our sterilizer maintenance.
@jenellealexis8219
3 жыл бұрын
This video really came in handy!!! my coworker is on vacation and showed me how to do maintenance a while ago, this was a great refresher!! thank you thank you!
@thachnguyen6588
2 жыл бұрын
so touching for an excellent video
@iskanderen659
2 ай бұрын
With a cool chamber drain and refill with distilled water Speed clean added to cool chamber Once wrapped cycle but stop when drying begins Drain again and refill Run unwrapped cycle, stop when drying begins Drain and refill Allow to cool. Remove trays Scrub. Remove filters and clean soap, brush, distilled water Wipe inside of autoclave behind careful not to damage heating element, Probe or water sensor Reinsert filters Reinstall trays Remove and clean door dam gasket. Clean with speed clean Place back ........ Verify pressure valve Place towel under autoclave Unwrapped and wait for pressure to reach 20psi then pull upward on valve for 20 seconds Allow to cool
@brittanyhughes3322
4 жыл бұрын
I was doing the monthly maintenance on the autoclave and when I was checking the valves the video you sent says to let the PSI get up to 20 and then release the steam. Our autoclave only went up to 13 and then let it out automatically. So I'm not sure if that's right?
@rosev366
Жыл бұрын
Hi it will release automatically 3 times before it reaches 20psi - it will reach 20 Psi when it heats to 258 F.
@MissCeliesLeftBraid
Жыл бұрын
Thank you! I literally just stopped it and restarted it. This is the second time I thought our machine had issues!
@asmaram9879
3 ай бұрын
I had no time to do monthly maintenance on same day, and it dissappeared after, then can i still do monthly maintenance after the sign is gone? I did it, but what am i doing wrong, it took so much time for first cycle? Am i doing something wring here
@cwsjohn
Жыл бұрын
After the rinse cycle after cooling you say to rinse the trays. The video shows the operator wetting the cloth with Speed Clean. Does the Speed Clean then stay on the trays? If I rinse without Speed Clean does it have to be distilled water?
@josephinemefferd5071
9 ай бұрын
Where do you find how many cycles have ran on the midmark 11?
@alexissager5778
Жыл бұрын
How do you take the ring out that holds the trays? Video doesn’t show.
@MidmarkDental
Жыл бұрын
Alexis, this video has actually been updated! Check it out here: kzitem.info/news/bejne/zZ6mvatorZOFnGk You can also check out the Daily + Weekly Maintenance video to see how to remove the tray rack: kzitem.info/news/bejne/0ayL3KeJrWp2n5w Thanks for your comment!
@kaitlyndickson2245
4 жыл бұрын
I sent the autoclave into a clean cycle with speed clean as said the instructions in the manual but after the autoclave was finished with the pouches cycle, I realized there was no more distilled water to run the unwrapped cycle. Will leaving my autoclave in an incomplete cycle harm it?
@caitlincarson2447
Жыл бұрын
After you run the cycle with speed clean you empty out whatever liquid is in the tube and fill with fresh distilled water and then run the unwrapped cycle!
@trenix3318
7 жыл бұрын
Do you leave the trays in while doing the wrapped and unwrapped cycle ?
@karissazenkner3964
5 жыл бұрын
yes! its only afterwards that you remove the trays to clean i believe
@arfbikes
4 жыл бұрын
I follow the instructions on the soap. It says to remove trays at the end and clean after
@verot.8683
8 ай бұрын
@@arfbikesI do it the way how was explained here. But one of coworkers insists the trays need to be out the autoclave. Two of them keep doing it wrong 🤦♀️
Пікірлер: 24