Great video! The detail you put into spring placement saved me. Super helpful.
@austinado16
2 ай бұрын
Great to hear! Thanks for the kind words!
@robertreynolds2690
6 күн бұрын
Excellent tutorial. Followed step by step and got it done!
@austinado16
6 күн бұрын
That's great! Nice job repairing your own equipment!
@rickydawson5321
3 ай бұрын
I’m so happy to see a video so well made, very well presented. I wished that when I was in school that my teachers were capable of giving instructions so plan and simple, I can watch or listen to you all day. Very, very good job. Thank you!!!
@austinado16
3 ай бұрын
I really appreciate the feedback, and the complement! You made my day!
@ScottyLo
Ай бұрын
Thank you thank you thank you. I couldn’t figure out how to re install the spring for the safety switch.
@austinado16
Ай бұрын
You're very welcome! There's a lot going on inside the handle, and the Stihls are probably the most difficult, out of the 3 or 4 commercial brands (Shindaiwa/Echo/Husqvarna/Honda).
@DavidSchuhart
3 ай бұрын
VERY EDUCATIONAL AND IN DEPTH ,NICE CLOSE UP PHOTOGRAPHY OF YOUR WORK . THANKS AGAIN.
@austinado16
3 ай бұрын
My pleasure! Thanks for nice comment David, you made my day!
@vernonfarabee
2 ай бұрын
My fs 130 is not going to full throttle I think it may be the cable now very informative video
@austinado16
2 ай бұрын
Use the torx headed adjustment screw that's up top, just inboard of the air filter cover, and screw the adjustment screw inward (clockwise) which will raise the curved plastic "bridge" that the throttle cable wraps around, and removes the slack in the cable. Adjust the screw "just" enough so that the throttle lever on the rear-facing side of the carburetor is almost touching the metal boss on the carburetor body, at full throttle. That will be plenty of throttle to achieve full throttle under load, and still give enough slack in the throttle cable that the throttle plate will snap back to idle position.
@paulthomas2813
Ай бұрын
Great video thanks 😊
@austinado16
Ай бұрын
Thanks for watching, and for the kind words!
@melvincherry5061
Ай бұрын
Part#? Thanks for the video
@austinado16
Ай бұрын
You're welcome. Always best to look up the part number for your own machine, so that you get the most accurate information.
@ltr06rider
3 ай бұрын
Can the newer 131r’s grip be installed on the older 110r and 130r’s?
@austinado16
3 ай бұрын
I'm guessing that the tube diameters are the same, but the functionality of the carburetor choke is completely different, and so is the connection of the throttle cable to the carburetor, so I don't see how the newer machine's grip could be used, or why using one would be something to pursue.
@ltr06rider
3 ай бұрын
@@austinado16 was just asking cause grip feels better and kill switch like better. Thanks for info.
@TR1CKSHOTS31
5 ай бұрын
Will this cable keep my stihl from turning on?
@austinado16
5 ай бұрын
There are quite a few things that will cause a Stihl 4Mix engine to not start.
@TR1CKSHOTS31
5 ай бұрын
@@austinado16 could you give me some ideas of what to look for or what to Check? Please. I checked the spark, light was glowing, valves seemed to be good, wasn’t hard to pull. I did spray starter fluid but didn’t seem to do anything. The throttle cable was frayed.. I’m not sure where to go from that. Thanks
@austinado16
5 ай бұрын
@@TR1CKSHOTS31 In all of my videos, you see me go through the diagnostic steps. Starting fluid doesn't work in 2 strokes.
@filibertovargas8354
4 ай бұрын
Thanks a ton for your video you are a really good teacher
@austinado16
4 ай бұрын
@@filibertovargas8354 Thanks for the kind words! You made my day!!
Пікірлер: 25