Interesting bit of trivia: "The Welch plug was originally designed in the 1900s by the Welch brothers at the Welch Motor Car Company of Pontiac, Michigan. At that time core holes in the engine blocks were fitted with pipe plugs. During one of these run-ins a pipe plug backed out. In order to get back on the road one of the brothers drove a quarter or half dollar into the hole. From this they developed the Welch plug,. They then patented the plug and the M.D. Hubbard Spring Company became the sole manufacturer of the Welch plug for the life of the patent." References
@wayneg5593
5 жыл бұрын
jj parody so, what was the “purpose of the plug to begin with? Just need to clarify!
@jerryf2426
6 жыл бұрын
PALAWNGUY: Dony wrap three layers of masking tape around the drill bit with only the amount of desired cutting extension protruding below the tape to help control the depth you feel you can drill in, also place a small amount of grease on this cutting end to help catch the chips. I would have extracted the chips with a shop vac rather than run the possibility of blowing some of them into the passages. Just some thoughts.
@edwardkawecki8101
5 жыл бұрын
To avoid drilling too far I use a wood dowel and drill through it and expose just enough of the drill to get through the part without going too far to cause damage. Like others have said, a piece of rubber tubing or hose works great also. Great informative videos, thank you.
@raymondcampbell2346
6 жыл бұрын
Great info video Don. Welch plugs are usually overlooked on a rebuild. Thanks for taking the time to show us.
@briancrull8678
5 жыл бұрын
Totally fixed a free snow thrower by replacement of a missing Welsh plug ! Thank so much for your help and knowledge 😁
@steveott1884
6 жыл бұрын
When I do the plugs I don't drill as it leaves too many shavings. I just use the punch and punch right through the plug and then pop it out. No debris that way. I do mostly old outboards though.
@coalitionofrob436
6 жыл бұрын
Donny I don’t think there is anything I couldn’t do to my gear from your videos! Good job mate
@BushcraftingBogan
5 жыл бұрын
Nice! Thank you! I was wondering why Or when I would ever need to replace them. Now I know. You’ve just saved me some time and effort, along with the tips required if I ever need to replace them.
@bigkk758
Жыл бұрын
This is probably what is wrong with my old carb on my Areins 924102 Tecumsah Snowblower. I clean the air screw and the brass bolt in the bowl and still the engine surged. I had no idea about these parts as I am new to these types of repairs. I will order a rebuild kit and welsh plugs for the old one and fix it up as a backup. I purchased a new carburetor on Amazon for 16.00 and it works perfect. Great video thanks for making this
@RussellBooth1977
6 жыл бұрын
I know on the Walbro carbys on the 2 stroke trimmers they say it doesn't hurt to apply a dab of nail polish to the outside of the Welsh plug(s),just for added sealability. I know about not needing any glue as I bought a bodgy carburetor which was like that,the main jet was glued in with Loctite & the fuel ate it away & gave me a lot of trouble with air & fuel leaks. Replacing the carby was the only quick solution. I've replaced welsh plugs on a car engine that I rebuilt,I removed the old ones to clean the water jackets,they do require sealant. There's quite a few tricks of the trade with repairing carburetors,Taryl has made himself some tools to replace the needle seat inside them.
@zx8401ztv
6 жыл бұрын
Smashing :-D I had to remove one last year to clean behind it. i also drilled a tiny hole in the center, i screwed a wood screw into the hole then carefully lifted the screw with wire cutters and a small bit of wood between the cutters and carb body to allow leverage. I didn't have a new plug so i reformed the dome shape, then soldered the tiny hole up. Tapped it back into place with a flat ended rod. Finally tested leaks by applying petrol, none got past the plug. Yes im a bit of a bodger, but this bodge seemed sound :-D
@georgedodd3970
6 жыл бұрын
There are plenty of acceptable methods . I would call yours the CORRECT method.
@zx8401ztv
6 жыл бұрын
George Dodd, Thank you :-D. As i come from a poor family, i could not afford to buy new things, so diy repairs were the norm :-D. It didn't do me any harm, shame that the current society seems to throw so much away.
@wiley0714
5 жыл бұрын
Any new kid would come with new plugs. You're going to take it apart to clean it and actually do the correct maintenance you would have had the new part. So that one day comes and it will when you go to start something and it don't run right you'll know why Dodger
@joef.3094
6 жыл бұрын
another great job ! i never take them out simply because i don't have replacements laying around . sometimes a carb still doesn't work right after cleaning and i wonder if removing the welsh plugs might result in a more thorough cleaning job. it would be really handy if there was a kit available with a wide assortment of these.
@MrAvant123
3 жыл бұрын
I had to throw away a walbro carb because it needed the welch plugs removing to clean debris and I had no way of reliably plugging the holes..
@ZombieDaveAZ
6 жыл бұрын
A self centering punch will remove welsh plugs and zero chance of slipping with the drill. Thats how I have been doing it for quite a while.
@bobadams1696
11 ай бұрын
I was looking for help with these. I didn’t even know what to call them learned much from your video and the good comments and tips.
@edwardkawecki8101
6 жыл бұрын
Good info thank you. one comment I would like to make when Drilling a blind hole and it is critical not to go too deep I like to take a small wooden dowel drill through it letting only part of the drill stick out deep enough to drill a minimum depth hole and not worry about any damage by drilling too deep thanks
@JimFixIt74
6 жыл бұрын
Been waiting for you to make a video about Welch Plugs. Great video Don and thank you!
@p.a.f.mitasol8071
6 жыл бұрын
Thankyou for the knowledge Id been overlooking all this time, not realizing I could do that job myself 👍 Cheers.
@999thenewman
6 жыл бұрын
Already done this. Hammer a center divot with a screwdriver bit. Hold in one hand. Drill in another. Start with a small bit. If you can't pick out the welch plug, drill a larger hole until you can pry it out. Put carb on bench or piece of wood. Tap in the new welch plug with a drill bit shank and claw hammer. It doesn't take much force to flatten.
@redgreen610
3 жыл бұрын
Grease on the drill bit also helps stick any particles to the drill so that nothing enters the passages. Thanks for the information! Am just going out to my shop to rebuild my outboard carbs and will remove welch plugs since they came with the rebuild kit.
@wiley0714
5 жыл бұрын
Finally got a chance to be a patreon. You've helped me from doing everything from getting my snowblower running two years in a row. To living the dream in flying. Thanks Don.
@Grumpyneanderthal
6 жыл бұрын
Thanks Donnie, I wasn’t able to get my Techumsee plug to hold. Now I know why. Tip on drilling to prevent plunging thru... use a piece of tubing cut to length and slid over drill bit only exposing enough to penetrate plug then it will act as a stop..... thanks for the tip
@googleplusisdead
6 жыл бұрын
How did you solve the not sealing plug problem?
@Grumpyneanderthal
6 жыл бұрын
Gogle Plus Sucks I didn’t, it’s been a while but as I recall I left them out. It runs....
@orange12v
6 жыл бұрын
Nice video a good way to stop you drilling to deep when you a job like this one is to have a drill bit reserved for it and drill out a few pop rivets with it leave the all pop rivet heads one this will act as depth stop and no damaged to the carb
@spudmanzz
5 жыл бұрын
orange12v jj
@Goomer
6 жыл бұрын
Thanks for taking some of the mystery out of it.
@TheEgg185
6 жыл бұрын
Never knew that had a name. Thank you.
@costasgeorgiou5015
6 жыл бұрын
So question..... There is a little tab there to flick out the Welch plug that's what I use why you drill it and take so much more work for yourself? The outside yes but not the inside one. Good video.
@JOEZEP54
6 жыл бұрын
Hi Donny, good tip.
@walter2670
6 жыл бұрын
Welch plugs are my favorite
@Kevin-cy9cv
2 жыл бұрын
Thank you, I've been looking for a video on this, I've got two Amal Concentrics to do.
@tellmesomething2go
6 жыл бұрын
Dony. Maybe a piece of tubing over the drill bit. with just enough bit showing. Drill stop.
@tracker335
Ай бұрын
Perfect ! Subscribed
@hatteraslabuf
2 жыл бұрын
Where to purchase an assorted of different sized Welch plugs?
@beeslandscaping
6 жыл бұрын
Great video and tip
@michaelchilders6056
4 жыл бұрын
Awesome!! Thank you!!👍
@maniyan_wanagi
6 жыл бұрын
Kinda looks like a Tillotson carb.... but maybe that's just my old eyes. Good basic lesson, Don - these things need to be taught these days - real mechanics and true repairs instead of replacing "assemblies" is a fast-dying art.
@edwardkawecki8101
6 жыл бұрын
Melquiades Estrada that is exactly what it looks like used on Old Harleys and Harley golf cars and many other older tractors. Thought the same thing as you did when I first saw it. And when rebuilding them use a ball pump to test for leaks in the Welch plug and diaphragms
@karlschwab6437
3 жыл бұрын
Good information Don. Now, how do you remove a main jet nozzle from a carburetor, such as a old Carter model "N" carburetor from a small engine? It is made of brass, has a slot for a perfectly fitting screwdriver, but will not budge. I have such a situation and it should be removed to clean any small holes. Thanks again.
@3qdx
Жыл бұрын
The one inside my Briggs and Stratton Carb came loose and fell out when I was cleaning it. I didn't know what it was and after the cleaning, I forgot to put it back in. Should I have or can the Carb run properly without it? Thanks.
@fattony123082
6 жыл бұрын
Doing great Don!!! 👍🏻👍🏻👍🏻
@nothankyou5524
5 жыл бұрын
Again, I say, nicely done
@wish2fish37
6 жыл бұрын
Good video Don..Did you ever do a video on replacing those lead shot plugs on a carb?I had one come loose on top of my Johnson outboard carb.Never saw one come loose before.The top of it popped off I guess leaving the piece going into the needle jet area loose.Motor started running terrible at idle.Took alittle bit of troubleshooting to figure it out.I did get info from some others on how to fix it.Hammered a piece of sinker in there and sealed it with a number of coats of good nail polish.
@darrensmith9143
6 жыл бұрын
I knew a 2 stroke mechanic who kept a bottle of nail polish in his shop for welch plug installation. He said fuel wouldn't touch the stuff.
@JOEZEP54
6 жыл бұрын
Years back I did the same but the fuel we have today not good mix.
@paulhaines5755
3 жыл бұрын
Nicley done. Thank you so much...
@marshallborder9089
5 жыл бұрын
Thanks for the lesson
@comet7894
3 жыл бұрын
I have a mower with a Briggs engine that is hard to start. I have taken the carb apart and discovered the two welch plugs were in the bowl and not attached to the carb. Could this cause a problem with starting? It has not yet been installed. Thank you.
@donyboy73
3 жыл бұрын
yes it could
@frerecampbell9291
4 жыл бұрын
Thanks for nice video, but I have a question. This first plug next to the center column, there are gaps in the circle. Won't these gaps nullify the need for a welch plug?
@hiphopman72
3 жыл бұрын
Thank
@raymondjiii
3 жыл бұрын
Great video as usual. I'm curious why B&S says to use enamel nail polish once the welch plug is put in. If you have a drill press it's a bit easier and you can almost guarantee that the drill bit will not hit the inside. I would love to see a video of those little rectangular welch plugs on 2 cycle engines - hot to remove and replace.
@nos9341
2 жыл бұрын
Donny is really flattening out that plug more than he needs too. Briggs tells you to use nail polish because it resists gasoline and seals the edges of the plug instead of really flattening it out like Donny does. I worry he might mash it in there too much and disturb things inside that metering chamber. Not only is there fuel in there but also air. You need a certain amount of space inside the chamber for those two components to mix so then they air and fuel passes through the tiny ports from the low side of the carb behind the throttle shutter they are a fine mist and not big droplet.
@tyroneclarke1666
3 жыл бұрын
Great video thank you Don 👍
@semco72057
6 жыл бұрын
I have a power generator with the Tecumseh engine and carburetor on it and never was used since I purchased it new in 2000. I have to get it working if the parts are available for it. I know the carburetor is in need of repair since it has been sitting so long without being used.
@andrewspiterie
5 жыл бұрын
I would like to buy a Welch Plug Kit with assorted sizes for all my diferent carbs. does anyone know where to by kits?
@RussellHoughton
3 жыл бұрын
I see them on eBay from time to time
@johngburtonbudzinski7608
3 жыл бұрын
@@RussellHoughton bantasaw dot com in warkworth ontario, kits online and fast service, been around 20 years and great product knowledges
@dh.mowersblowersservicesll4061
6 жыл бұрын
Great video thanks for the tips . But I was just wondering which carburetor cleaner do u use to clean your carburetors ?, the reason I ask is because a lot of them will destroy any rubber on carbs an I've learned the hard way an had to buy replacement parts .
@marks5239
5 жыл бұрын
Super helpful video - but I have a nikki carb off of a case tractor. Do you know where I can find a plug for it?
@frederickjuneau7874
6 жыл бұрын
Good tips as usual Dony!!! 👍👍👍👍
@gracewhite2742
5 жыл бұрын
I have question for the dome shape plugs is there a spécial tool to put them in. This will be my first time replace the plugs but ive rebuilt plenty of carbs i never did plugs thinking i needed speical tool to put them in. I can do it your way just woundering if they sell such a tool for that might be nice to have.
@opichocal
6 жыл бұрын
Could you do a video on STIHL carbs and what causes them to idol ok but they have problems running full throttle? I have to run mine 3/4 choke to get them to run up. Thanks and great videos as always!
@donyboy73
6 жыл бұрын
kzitem.info/news/bejne/q2eQwKqtm3yeqKw
@jeffbarnum1187
6 жыл бұрын
check your spark arrestor in the muffler too.. if it has one
@teddybanks4270
3 жыл бұрын
Are all Tecumseh small engine Welch plugs the same size? I got a 642-15B carb kit but the Welch plug was too large.
@queenstownkid
6 жыл бұрын
great tip thanks don
@DaleB809
5 жыл бұрын
Lately I have bought new carbs and there is no welch plug on the inside where the float sits. Is this a new design or is it really needed. It seems to work fine
@ohUredneck
6 жыл бұрын
Thanks for the info!
@jamesmullins3219
6 жыл бұрын
great tips, thanks
@tonym6920
6 жыл бұрын
Nice video Dony. Do you ever replace the plugs on a Zama carb. Would the same procedure apply? They're a lot smaller and must be a pain to get put. Have a great weekend Dony
@Jim_Austin
6 жыл бұрын
Where do you obtain replacement plugs? Do you buy them individually or do they come in an assortment?
@googleplusisdead
6 жыл бұрын
Usually come in full carb rebuild kits. Otherwise you'd have to buy from manufacturer dealer, or carefully measure and buy, probably online.
@geojor
6 жыл бұрын
valuable info ...
@chrisdaunhauer1757
2 жыл бұрын
Where can I buy an assortment of these plugs ? The carb on my JD x300 is missing a small welch plug on the top above the tip of the emulsion tube and the air leak from the missing plug is creating surging idle that cannot be influenced by the pilot jet needle valve. I assume the plug fell out sometime in the past (?) I have a dab of silicone sealing the hole now but would rather use a metal plug if I can find one.
@bikeski1956
2 жыл бұрын
Silicone is bad, crystalizes and clogs the passages inside a carb, that's why I'm rebuilding 3 carbs off an outboard. The previous owner used silicone to "seal" the gas line fittings from fuel tank to the outboard. What a mess!
@anoushs.afshar2134
6 жыл бұрын
Dear Donyboy 73 I need your help. I have engine Tecumseh OVXL120-202704 and when I turn it on it start with high speed and the leaver for speed doesn't work, also I have to say I opened the carburetor and cleaned with purple power but I didn't changed any thing in it. Help me
@genehensley767
6 жыл бұрын
Your Genius
@christopherfisher123
4 жыл бұрын
uh oh!!!); hey my dumb ass just accidentally drilled into to carb itself under the plug!Is there any way i can fill the hole with jb weld or anything that will last and hold up to the fuel and oil?it an old series 2 tecumseh outboard carb!im kicking myself hard right now!!!!plz help!
@Huss-iw6ph
5 жыл бұрын
Dony, where do you buy Welch plugs, and do they sell pkgs of assorted different sizes. Thx
@dontblameme6328
4 жыл бұрын
You can get them from your local pharmacy.
@Huss-iw6ph
4 жыл бұрын
Yeh! Found em under buttplugs.
@unfundedopportunities7278
5 жыл бұрын
Where does the tiny vent hole at the bottom middle of the screen at 2:27 go? I tried putting a vacuum pump on mine and is seems plugged.
@mikeys1stphone191
6 жыл бұрын
Nice tip 🙆👍👍👍👍
@georgedodd3970
6 жыл бұрын
Try using a sharp drill to drill any holes. For this job , please use 118 degree drill. Don't push hard.
@seansysig
6 жыл бұрын
I have a Briggs & Stratton 19.5 Intel XRD Model#31P677 Type: 137381 Code: 0911167D Can you recommend a new carb. I tried cleaning jets with carb cleaner. Low idle it runs OK, above 1/2 throttle to full throttle it misfires. There is a lot of Chinese ones, hard to tell which are the good ones.
@Derpy1969
3 жыл бұрын
Thanks! Why are they called Welch plugs?
@scooterman1965
4 жыл бұрын
Where can you get new welch plugs?
@juanstill
5 жыл бұрын
When I disassemble for the first time the carburetor of my Briggs and Stratton 650 there was a welch plug missing. Probably some previous repair man that I gave the lawn mower miss it. I wonder if I should replace it (it works fine without it, I think...). Also if someone knows how I’ve got to order a “Welch plug” in spanish, it would be helpful to illustrate me because I can’t translate the concept.
@thersten
5 жыл бұрын
Mostra Les una foto. No se como se dice welsh plug en espanol tanpoco.
@buddha65281
4 жыл бұрын
any idea as where to order Welch plugs online in the USA? Thanks
@donyboy73
4 жыл бұрын
www.discountonlineparts.com
@greghaaland7913
4 жыл бұрын
Where cab I buy welch plugs?
@billk5727
6 жыл бұрын
Great video! Take care.
@Fireship1
6 жыл бұрын
I've taken lots of these out. But it's kind of a nerve racking process every time I do it. Some of these carbs (especially on outboards) are very expensive. Always afraid I might punch too far through and mess up the carb.
@DougHinVA
5 жыл бұрын
what ARE they? Did I miss your explanation what they do ?
@catdakman1273
3 жыл бұрын
Why do you work on very dirty carbs ??
@michaelspeakman8924
6 жыл бұрын
How come you don't you put back the Welch plugs in all of the carburetors I noticed that you don't do that
@marcogram1216
6 жыл бұрын
He explained it in the video.
@franktorres1898
5 ай бұрын
Why replace Welch plug on carb.
@MrAvant123
3 жыл бұрын
Question is not how to remove them its more, where do you get replacements ? Good vid though...
@donyboy73
3 жыл бұрын
check discountonlineparts.com
@StanWilhite
6 жыл бұрын
What does a welch plug do?
@StanWilhite
6 жыл бұрын
Glyn, thanks! Stan
@rk22cc
6 жыл бұрын
What is a Welch Plug?
@googleplusisdead
6 жыл бұрын
Watch video, those are welch plugs.
@eltonpham2165
6 жыл бұрын
What does a Welch plug do and the purpose of it?
@999thenewman
6 жыл бұрын
rk22cc A Welch plug is a specifically sized space that acts as a vacuum port to regulate air intake flow through the carburetor to help meter the air with the flow of fuel.
@josephnovotnak
3 жыл бұрын
What do Welch plugs do?
@73superglide62
6 жыл бұрын
Y is it that need replace it
@juss-passin-thru
6 жыл бұрын
I don't know why don't just make them threaded??
@woodstover
Жыл бұрын
Adds to the cost of manufacturing the carb and they don't normally need to be removed.
@juss-passin-thru
Жыл бұрын
@@woodstover thanks for responding to me 4 years later 😂🤣
Пікірлер: 120