I just used your method and it worked Great. I don't own a drill or good self taping screws so I used an awl from a Swiss army knife to make a starter hole then used an screw eye to screw into the plug. I liked this very much because it got really hard to turn and I had to use a pair of pliers to turn the screw eye. I could not have done that without the screw eye head to grab into with the pliers. I was a little off center, but it worked just fine. Thanks.
@TheRepairSpecialist
Жыл бұрын
Awesome. Thank you for letting me know. I really appreciate your feedback. I’ve pinned your comment. Hope that’s ok 👍
@DivergentDroid
Жыл бұрын
@@TheRepairSpecialist That's just fine. Hope it helps someone. Getting to the fuel screw and trying to adjust it didn't help my scooter stay running. Tomorrow my project will be to slot out the screws that hold the float bowl together so I can clean the jets.
@dustinwise8759
4 жыл бұрын
Thank you, your videos have been extremely helpful and very informative. Countless topics to be learned as a result and anyone can benefit from them. Again thank you for taking time to share.
@richardcole6566
4 жыл бұрын
Using a self-taping screw was very impressive. All other removing styles needed a drill. I really like you alternative method. . Thank You
@TheRepairSpecialist
4 жыл бұрын
Thank you so much for the nice feedback. I really appreciate it. Craig
@AndysDogHouse
4 жыл бұрын
Another very helpful video. You have lots of tricks up your sleeve. Thanks for sharing.👍👍
@bobadams1696
11 ай бұрын
Worked great. Outboard running it’s best now.
@TheRepairSpecialist
11 ай бұрын
Great to hear! Thank you. Craig
@frogfoot198
4 жыл бұрын
Well done sir! Indeed a better alternative.
@bobadams1696
11 ай бұрын
Very helpful. I’ll try it.
@TheRepairSpecialist
11 ай бұрын
Awesome. Thanks
@GRTechOfficial
4 жыл бұрын
Thanks for sharing this informative video
@themowerman
4 жыл бұрын
Good video..
@TheRepairSpecialist
4 жыл бұрын
Glad you liked it!
@justinc9911
4 жыл бұрын
very nice. is it possible that the Welch plug is under the carb in front of the air intake hole??
@grtntgod
2 жыл бұрын
Thanks
@TheRepairSpecialist
2 жыл бұрын
👍👍
@metheewatchakittikorn4796
4 жыл бұрын
If this plug was put on while manufactured, why do we have ot remove it? I'm just curious what those little holes inside are for?
@TylerTheBassCreator
2 жыл бұрын
Adjustment screw underneath it
@metheewatchakittikorn4796
2 жыл бұрын
@@TylerTheBassCreator Thank you very much
@jtaylor2563
Жыл бұрын
Do they make those plugs out of plastic also?
@TheRepairSpecialist
Жыл бұрын
I personally haven’t seen anything like that on a small carb like this
@johnnyb5648
3 жыл бұрын
When I tapped the screw onto my plug to try and thread it through the plug only sunk down to the air screw. Trying to raise it back up I broke a small pick off in the pilot hole. Any suggestions now?
@aannddrreeww1000
Жыл бұрын
This is exactly what I’m afraid of doing. I’m going to use a drill and I tiny drill bit. I Dont want to compress the thin plug even deeper down the hole, making it even harder to extricate. Hmmm!
@MrChickensnatcher
Жыл бұрын
Can a carburetor run without a wlech plug?
@TheRepairSpecialist
Жыл бұрын
To be honest. Ive never tried. I don’t hold much hope that it will.
@DivergentDroid
Жыл бұрын
The carb will run without a welch plug but the bike may refuse to move on principle that it was violated. 😁
@76629online
3 жыл бұрын
I usually just produce a picture of my ex-wife - they come right out and leave the room all on their own.
Пікірлер: 32