Vielen Dank, werde im Frühling ebenfalls meinen Kettensatz wechseln.
@mt-elinap5975
5 жыл бұрын
Viel Erfolg
@2lbsTrigrPull
2 жыл бұрын
Warum Endloskette und der Aufwand die Schwinge zu lösen?
@elinap2002
2 жыл бұрын
YAMAHA sieht in seiner Reparaturanleitung dies aus Sicherheitsgründen so vor. ALLE Nieten sind werkseitig gleich verpresst
@ivanhorvat4817
5 жыл бұрын
Nice maintenace, very clean motorcycle! Way to go...
@chuabetheratbruno6359
5 жыл бұрын
THANKS VERY MUCH!!! GRACIAS!!! MUY BUENO EL VIDEO !!
@andreusdelporto1984
2 жыл бұрын
thank you for this video. very useful and very well done, better than the workshop manual
@ChrisAkAxTr3Me
4 жыл бұрын
Sehr gut gemacht, schönes Video und sauber gearbeitet!
@lppedd
5 жыл бұрын
Thank you so much for this video! Really well done and understandable, even if I don't understand your language. Just a question, what's the wrench insert size for the front sprocket?
@elinap2002
5 жыл бұрын
30 or 32 mm
@elinap2002
5 жыл бұрын
30 mm with 95 Nm is korrektly !!
@lppedd
5 жыл бұрын
@@elinap2002 Awesome! Thanks again!
@MrRui33333
2 жыл бұрын
perfet job !!!
@Niccoo22
Жыл бұрын
Müssen die Ritzel immer mit getauscht werden beim Ketten Wechsel ? Fahre eine MT 125 und kette ist jetzt fällig bei 12000 Laufleistung .
@elinap2002
Жыл бұрын
wenn Kette und Kettenrad neu sein soll, kommst auch nicht auf das tauschen des Ritzel an. Sollte bei der Aktion mit getauscht. -Teile sind im Zubehör auch recht günstig. Bei der Kette nicht sparen sondern DID Ketten verwenden.
@tnttrx
Жыл бұрын
Was it necessary to get new front sprocket nut, or the old one could be re-used?
@mementomori4972
5 ай бұрын
It's an older comment, but i will answer anyways in case someone else reads it. Yes it is necessary to change both sprockets when you replace the chain. The sprockets and the chain wear in on each other. It is however not necessary, nor is it good practice to remove this frame/chain covers and losen swing arm bolts, just to thread the chain trough there. The chain usually comes with an open link and you connect the links on the bike. Depending on the link type, either with a chain tool or with a pair of pliers, if it is a snap on type link.
@tnttrx
5 ай бұрын
@@mementomori4972 Thx, although my question was about front sprocket nut which has a metal lip part to fix it on the shaft
@robertweise8924
2 жыл бұрын
Funktioniert deine Anleitung auch bei der MT 07 2021 ? Also die NM angaben zb ?
@deniss4755
2 жыл бұрын
Ja ist alles gleich, habe selber eine von 2021.
@robertweise8924
2 жыл бұрын
@@deniss4755 Mit wieviel wird die Schwingemutter die man locker schraub angezogen ?
@deniss4755
2 жыл бұрын
@@robertweise8924 105nm
@sweedieman3231
3 жыл бұрын
5:01 the part no one on youtube for some reasons dont show. Axle is stuck and I want to find out why so that I can take out the rear wheel
@ToleXMusic
Жыл бұрын
No easy way around it in my experience. Had to grind it off eventually. Which wasn't easy and very delicate.
@killerkolibri
3 жыл бұрын
Mein Ganghebel ließ sich auf diese Art nicht entfernen
Пікірлер: 25