How To Scan Nigcomsat And Turksat On Newmax Decoder
To scan for channels on Nigcomsat and Turksat using a Newmax decoder, you'll need to follow a series of steps to configure the decoder and ensure it's pointed at the correct satellites. Here's a step-by-step guide to help you through the process:
Materials Needed
- Newmax decoder
- Satellite dish
- LNB (Low-Noise Block downconverter)
- Coaxial cable
- TV set
- Remote control for the Newmax decoder
Steps
#### 1. *Install and Align the Satellite Dish*
- Ensure your satellite dish is installed in a location with a clear line of sight to the sky.
- Nigcomsat is located at 42.5° East, and Turksat is located at 42° East. You need to align your dish to these orbital positions. If you want to receive signals from both satellites, you may need a dish with multiple LNBs or use a motorized dish setup.
#### 2. *Connect the Equipment*
- Connect the LNB to the satellite dish arm.
- Run the coaxial cable from the LNB to the Newmax decoder.
- Connect the Newmax decoder to your TV using an HDMI cable or AV cables (depending on the available ports).
#### 3. *Configure the Newmax Decoder*
- Turn on the TV and the Newmax decoder.
- Use the remote control to navigate to the decoder's menu.
- Go to the *Installation* or *Setup* menu.
#### 4. *Add or Configure Satellites*
- In the *Satellite Setup* menu, add Nigcomsat (42.5°E) and Turksat (42°E) if they are not already listed.
- You may need to enter specific parameters such as:
- **Frequency**: LNB frequency, symbol rate, and polarization.
- Nigcomsat example frequencies (check for current active frequencies):
- 12518 MHz, H, 29500 ksps
- Turksat example frequencies:
- 12729 MHz, V, 30000 ksps
- These parameters can usually be found on websites like LyngSat or other satellite information sources.
#### 5. *LNB Configuration*
- Ensure the LNB type is correctly set to *Universal* (9750/10600) if you are using a universal LNB.
- Set the DiSEqC switch settings if you are using a switch to combine multiple LNBs.
#### 6. *Signal Strength and Quality*
- Use the signal strength and quality bars to align your dish accurately. This may require slight adjustments to the dish's azimuth (left-right), elevation (up-down), and skew (rotation).
#### 7. *Blind Scan or Manual Scan*
- Perform a *Blind Scan* or *Auto Scan* to search for all available channels on Nigcomsat and Turksat:
- Navigate to the *Blind Scan* option in the installation menu.
- Select the satellite you want to scan (Nigcomsat or Turksat).
- Start the scan and wait for it to complete. The decoder will automatically find and store all available channels.
- Alternatively, you can do a *Manual Scan* by entering specific transponder details and scanning each one individually.
#### 8. *Save and Exit*
- Once the scan is complete, save the found channels.
- Exit the menu and start watching the channels.
Troubleshooting Tips
- *No Signal or Weak Signal:*
- Ensure the dish is correctly aligned to the satellite's orbital position.
- Check all cable connections between the LNB and the decoder.
- Verify that the LNB frequency and other settings are correctly configured.
- *No Channels Found:*
- Make sure the satellite and transponder parameters are correctly entered.
- Try performing a blind scan instead of a manual scan.
By following these steps, you should be able to scan and receive channels from Nigcomsat and Turksat on your Newmax decoder. Ensure you have the latest satellite parameters, as these can change over time.
_____________________________________
LINKS
Visit The WEBSITE for more Info:
www.pbteck.com
INSTAGRAM;
/ pbtecknology
FACEBOOK;
/ pbtecknology
TWITTER
/ pbtecknology
TELEGRAM:
t.me/pbtecknology
PBTECKNOLOGY
/ pbtecknology
Негізгі бет 🔵 How To Scan Nigcomsat 42.5°E And Turksat 42.0°E On Newmax Decoder | Pbteck
Пікірлер